From: "Markus Jordan" <k0156448@students.jku.at>
To: <linux-kernel@vger.kernel.org>
Subject: PROBLEM: lost interrupt
Date: Wed, 30 Jan 2002 00:27:15 +0100 [thread overview]
Message-ID: <000001c1a91c$7fcb8fb0$b121abc1@compus> (raw)
[1.] I get the message " hda: lost interrupt" at the startup of the
kernel
[2.]
PCI: using IRQ 14 for Device 00:07.5
PCI: routing conflict for 00:0C.1, have IRQ 10, want IRQ 14
....
....
....
hda: FUJITSU, MHN2300AT, ATA Disk Drive
hda: IRQ Probe failed ( 0xfffffff8)
hdb: IRQ Probe failed ( 0xfffffff8)
hdb: IRQ Probe failed ( 0xfffffff8)
hdc: is the CD-ROM - Drive, right checked
ide0 at 0x1f0-0x1f7, 0x3f6 on IRG 14
ide1 at 0x170-0x177, 0x376 on IRG 15
hda: information about sectors, are right
Partition Check
hda:had: lost interrupt
had: lost interrupt
had: lost interrupt
had: lost interrupt
hda1 hda2 hda3 hda4 < had: lost interrupt
hda5 had: lost interrupt
hda6 had: lost interrupt
hda7 had: lost interrupt
hda8>
...
...
...
after "freeing unused Kernel memory : 208K "
"had: lost interrupt" appears often, it doesn't go on any further
So the kernel doesn't start. The only way to boot is a Suse CD-Rom with
a kernelversion of 2.2.18, break the installation, and start the kernel
2.4.17 with that system.
[3.] harddisk, IRQ - problem,
[4.] at the moment 2.4.17, but it also appears in 2.4.12
[7.]
[7.1.]
If some fields are empty or look unusual you may have an old version.
Compare to the current minimal requirements in Documentation/Changes.
Linux Computix 2.2.18 #1 Wed Jan 24 12:28:55 GMT 2001 i686 unknown
Gnu C 2.95.2
Gnu make 3.78.1
binutils 2.9.5.0.37
util-linux
util-linux Note: /usr/bin/fdformat is obsolete and is no
longer available.
util-linux Please use /usr/bin/superformat instead (make
sure you have the
util-linux fdutils package installed first). Also, there
had been some
util-linux major changes from version 4.x. Please refer to
the documentation.
util-linux
mount 2.10f
modutils 2.4.6
e2fsprogs 1.18
pcmcia-cs 3.1.8
PPP 2.3.11
Linux C Library 2.1.3
ldd: version 1.9.11
Procps 2.0.6
Net-tools 1.54
Console-tools 0.2.3
Sh-utils 2.0
Modules Loaded lp parport_pc parport ds i82365 pcmcia_core
mousedev keybdev hid input usb-uhci usbcore 8390 nvram
[7.2.] nothing in there ( It is Pentium III / 1200 Mhz )
[7.3.] nothing in there
[7.4.] nothing in ioports, iomem doesn't exist
[7.5.]
00:00.0 Host bridge: VIA Technologies, Inc. VT82C691 [Apollo PRO] (rev
c4)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ >SERR- <PERR+
Latency: 0 set
Region 0: Memory at e8000000 (32-bit, prefetchable)
Capabilities: [a0] AGP version 2.0
Status: RQ=31 SBA+ 64bit- FW- Rate=421
Command: RQ=0 SBA+ AGP+ 64bit- FW- Rate=4
Capabilities: [c0] Power Management version 2
Flags: PMEClk- AuxPwr- DSI- D1- D2- PME-
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:01.0 PCI bridge: VIA Technologies, Inc. VT82C598 [Apollo MVP3 AGP]
(prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ >SERR- <PERR-
Latency: 0 set
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 00009000-00009fff
Memory behind bridge: e0000000-e00fffff
Prefetchable memory behind bridge: f0000000-f7ffffff
BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
Capabilities: [80] Power Management version 2
Flags: PMEClk- AuxPwr- DSI- D1- D2- PME-
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:06.0 Communication controller: Lucent Microelectronics: Unknown
device 0450
Subsystem: Askey Computer Corp.: Unknown device 4005
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR+
Interrupt: pin A routed to IRQ 10
Region 0: Memory at fbefab00 (32-bit, non-prefetchable)
Region 1: I/O ports at fff0
Region 2: I/O ports at f800
Capabilities: [f8] Power Management version 2
Flags: PMEClk- AuxPwr+ DSI+ D1+ D2+ PME-
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:07.0 ISA bridge: VIA Technologies, Inc. VT82C686 [Apollo Super] (rev
40)
Subsystem: VIA Technologies, Inc.: Unknown device 0000
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping+ SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0 set
Capabilities: [c0] Power Management version 2
Flags: PMEClk- AuxPwr- DSI- D1- D2- PME-
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:07.1 IDE interface: VIA Technologies, Inc. VT82C586 IDE [Apollo] (rev
06) (prog-if 8a [Master SecP PriP])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 set
Region 4: I/O ports at 1000
Capabilities: [c0] Power Management version 2
Flags: PMEClk- AuxPwr- DSI- D1- D2- PME-
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:07.2 USB Controller: VIA Technologies, Inc. VT82C586B USB (rev 1a)
(prog-if 00 [UHCI])
Subsystem: Unknown device 0925:1234
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV+ VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 set, cache line size 08
Interrupt: pin D routed to IRQ 5
Region 4: I/O ports at 1020
Capabilities: [80] Power Management version 2
Flags: PMEClk- AuxPwr- DSI- D1- D2- PME-
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:07.4 ISA bridge: VIA Technologies, Inc. VT82C686 [Apollo Super ACPI]
(rev 40)
Subsystem: VIA Technologies, Inc.: Unknown device 3057
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Capabilities: [68] Power Management version 2
Flags: PMEClk- AuxPwr- DSI- D1- D2- PME-
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:07.5 Multimedia audio controller: VIA Technologies, Inc. VT82C686
[Apollo Super AC97/Audio] (rev 50)
Subsystem: FIRST INTERNATIONAL Computer Inc: Unknown device 1840
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin C routed to IRQ 0
Region 0: I/O ports at 1400
Region 1: I/O ports at 1014
Region 2: I/O ports at 1010
Capabilities: [c0] Power Management version 2
Flags: PMEClk- AuxPwr- DSI- D1- D2- PME-
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:09.0 Ethernet controller: Accton Technology Corporation: Unknown
device 1216 (rev 11)
Subsystem: Accton Technology Corporation: Unknown device 2242
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 10
Region 0: I/O ports at f900
Region 1: Memory at fbefac00 (32-bit, non-prefetchable)
Capabilities: [c0] Power Management version 2
Flags: PMEClk- AuxPwr- DSI- D1+ D2+ PME+
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:0c.0 CardBus bridge: O2 Micro, Inc.: Unknown device 6933 (rev 01)
Subsystem: O2 Micro, Inc.: Unknown device 6933
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping+ SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 168 set
Interrupt: pin A routed to IRQ 10
Region 0: Memory at 20000000 (32-bit, non-prefetchable)
Bus: primary=00, secondary=20, subordinate=22, sec-latency=176
Memory window 0: 00000000-00000000
Memory window 1: 00000000-00000000
I/O window 0: 00000000-00000003
I/O window 1: 00000000-00000003
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt+
PostWrite+
16-bit legacy interface ports at 0087
00:0c.1 CardBus bridge: O2 Micro, Inc.: Unknown device 6933 (rev 01)
Subsystem: O2 Micro, Inc.: Unknown device 6933
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping+ SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 168 set
Interrupt: pin B routed to IRQ 10
Region 0: Memory at 20001000 (32-bit, non-prefetchable)
Bus: primary=00, secondary=23, subordinate=25, sec-latency=176
Memory window 0: 00000000-00000000
Memory window 1: 00000000-00000000
I/O window 0: 00000000-00000003
I/O window 1: 00000000-00000003
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt+
PostWrite+
16-bit legacy interface ports at 0087
00:0d.0 FireWire (IEEE 1394): Lucent Microelectronics: Unknown device
5811 (rev 04) (prog-if 10 [OHCI])
Subsystem: FIRST INTERNATIONAL Computer Inc: Unknown device 1881
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 10
Region 0: Memory at ffeff000 (32-bit, non-prefetchable)
Capabilities: [44] Power Management version 2
Flags: PMEClk- AuxPwr- DSI- D1+ D2+ PME+
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
01:00.0 VGA compatible controller: ATI Technologies Inc: Unknown device
4c59 (prog-if 00 [VGA])
Subsystem: FIRST INTERNATIONAL Computer Inc: Unknown device 1930
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping+ SERR- FastB2B+
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 5
Region 0: Memory at f0000000 (32-bit, prefetchable)
Region 1: I/O ports at 9000
Region 2: Memory at e0000000 (32-bit, non-prefetchable)
Capabilities: [58] AGP version 2.0
Status: RQ=47 SBA+ 64bit- FW- Rate=421
Command: RQ=31 SBA+ AGP+ 64bit- FW- Rate=4
Capabilities: [50] Power Management version 2
Flags: PMEClk- AuxPwr- DSI- D1+ D2+ PME-
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
[7.6.] nothing in there
[7.7.] I didn't found any informations in /proc, except the mtrr, but
that isn't useful, I think.
I don't exactly know if this is really a kernel bug or if I have some
wrong configurations. If the latter one is true, I hope you could give
me some advice.
If you had any further question, I will give you as much information as
I can.
Yours, Grateful
Markus Jordan
Computix@gmx.at
>From Linz, Austria
next reply other threads:[~2002-01-29 23:30 UTC|newest]
Thread overview: 2+ messages / expand[flat|nested] mbox.gz Atom feed top
2002-01-29 23:27 Markus Jordan [this message]
2002-01-29 23:55 ` PROBLEM: lost interrupt Alan Cox
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to='000001c1a91c$7fcb8fb0$b121abc1@compus' \
--to=k0156448@students.jku.at \
--cc=linux-kernel@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.