From: "Doug Smythies" <dsmythies@telus.net>
To: "'Zak'" <zakbrightonknight@gmail.com>, <linux-pm@vger.kernel.org>,
"'Rafael J. Wysocki'" <rafael@kernel.org>,
"'Srinivas Pandruvada'" <srinivas.pandruvada@linux.intel.com>
Cc: "'Len Brown'" <lenb@kernel.org>,
"'Viresh Kumar'" <viresh.kumar@linaro.org>,
<linux-kernel@vger.kernel.org>, <stable@vger.kernel.org>,
"Doug Smythies" <dsmythies@telus.net>
Subject: RE: [PATCH] cpufreq: intel_pstate: Restore P-state request on resume without HWP
Date: Tue, 27 Oct 2026 09:36:55 -0700 [thread overview]
Message-ID: <001101dd6631$6167dbd0$24379370$@telus.net> (raw)
In-Reply-To: <20261027143725.3763827-1-zakbrightonknight@gmail.com>
On 2026.10.27 07:37 Zak Brighton Knight wrote:
> From: Zak Brighton Knight <zakbrightonknight@gmail.com>
>
> On a ThinkPad T520 with an i7-3840QM (Ivy Bridge) running coreboot,
> the CPUs stop using turbo after every suspend to RAM when intel_pstate
> is in passive mode with the performance governor: they stay at the
> 2.8 GHz base frequency instead of boosting up to 3.8 GHz, until the
> policy limits change or the system is rebooted.
>
> During resume, the firmware sets each CPU's P-state request register,
> MSR_IA32_PERF_CTL, to the base ratio (28), and the kernel never writes
> the requested turbo ratio (38) again. Without hardware-managed
> P-states (HWP), intel_pstate caches the last P-state it wrote and
> skips writes that would not change it. In passive mode the cpufreq
> core also skips requests for the frequency it believes is already set
> (policy->cur), because intel_cpufreq sets CPUFREQ_NEED_UPDATE_LIMITS
> only with HWP. Neither cached value is updated across suspend and
> resume, so as long as the governor keeps requesting the same P-state,
> as the performance governor always does, the register is never
> rewritten. Governors that change the request often, such as
> schedutil, mostly hide the problem.
>
> Fix this by writing the cached P-state back to the register in
> intel_pstate_resume() when HWP is not used, as is already done for
> the HWP request when it is.
>
> The problem was found and root-caused, and this patch was drafted, with
> the help of an AI coding assistant (Claude, by Anthropic) during a
> performance review of the machine described above.
>
> Fixes: 001c76f05b01 ("cpufreq: intel_pstate: Generic governors support")
> Cc: stable@vger.kernel.org
> Signed-off-by: Zak Brighton Knight <zakbrightonknight@gmail.com>
> ---
> Tested on the T520 (i7-3840QM, no HWP, coreboot 24.08 with SeaBIOS)
> with v7.3 plus this patch and a temporary module parameter, not part
> of this patch, to turn the fix off. intel_pstate.c is the same in
> v7.3 and in the base commit below.
>
> Each row is one suspend to RAM and resume (rtcwake -m mem -s 25).
> "Request" is the P-state read back from PERF_CTL on all eight CPUs
> 5 and 17 seconds after resume; "clock" is the measured speed of a
> single-threaded busy loop. Before every suspend, all CPUs requested
> 38 and the clock was about 3.8 GHz.
>
> mode governor fix request after resume clock
> passive performance on 38 on all CPUs 3.8 GHz
> passive performance off 28 on all CPUs 2.8 GHz
> active performance off 38 on all CPUs 3.8 GHz
> active performance on 38 on all CPUs 3.8 GHz
>
> The passive-mode failure was also reproduced twice on Fedora's 7.2.11
> kernel. In active mode the request was back at 38 after resume even
> without the fix, so on this machine the fix only makes a difference in
> passive mode, the default without HWP.
>
> Not tested: systems with HWP (their code path is unchanged, only
> restructured), other machines and firmware, and suspend-to-idle. The
> patch adds no warnings with W=1; sparse was not run. The tests were
> scripted and run by the same AI assistant.
>
> drivers/cpufreq/intel_pstate.c | 16 +++++++++++++---
> 1 file changed, 13 insertions(+), 3 deletions(-)
>
> diff --git a/drivers/cpufreq/intel_pstate.c b/drivers/cpufreq/intel_pstate.c
> index 17158cb..53db91a 100644
> --- a/drivers/cpufreq/intel_pstate.c
> +++ b/drivers/cpufreq/intel_pstate.c
> @@ -1371,6 +1371,7 @@ static void set_power_ctl_ee_state(bool input)
> }
>
> static void intel_pstate_hwp_enable(struct cpudata *cpudata);
> +static void intel_pstate_set_pstate(struct cpudata *cpu, int pstate);
>
> static void intel_pstate_hwp_reenable(struct cpudata *cpu)
> {
> @@ -1404,11 +1405,20 @@ static int intel_pstate_resume(struct cpufreq_policy *policy)
> else if (power_ctl_ee_state == POWER_CTL_EE_DISABLE)
> set_power_ctl_ee_state(false);
>
> - if (cpu->suspended && hwp_active) {
> + if (cpu->suspended) {
> mutex_lock(&intel_pstate_limits_lock);
>
> - /* Re-enable HWP, because "online" has not done that. */
> - intel_pstate_hwp_reenable(cpu);
> + if (hwp_active) {
> + /* Re-enable HWP, because "online" has not done that. */
> + intel_pstate_hwp_reenable(cpu);
> + } else {
> + /*
> + * PERF_CTL may have been changed by the platform
> + * firmware, but it is only written when the requested
> + * P-state changes, so restore it explicitly.
> + */
> + intel_pstate_set_pstate(cpu, cpu->pstate.current_pstate);
> + }
>
> mutex_unlock(&intel_pstate_limits_lock);
> }
>
> base-commit: d135ab453a7400a34930bdda1ef4bdc8acfac80e
> --
> 2.56.0
I confirm your findings and tested your proposed patch. It all worked fine.
I had not seen Rafaels's reply about a possible race condition until now.
Test computer: i5-10600K, 6 cores, 12 CPUs, HWP disabled.
... Doug
next prev parent reply other threads:[~2026-10-27 16:36 UTC|newest]
Thread overview: 11+ messages / expand[flat|nested] mbox.gz Atom feed top
2026-10-27 14:37 [PATCH] cpufreq: intel_pstate: Restore P-state request on resume without HWP Zak
2026-10-27 15:56 ` Rafael J. Wysocki (Intel)
2026-10-27 16:36 ` Doug Smythies [this message]
2026-10-27 20:32 ` Rafael J. Wysocki (Intel)
2026-10-27 21:46 ` Doug Smythies
2026-10-28 15:54 ` Rafael J. Wysocki (Intel)
2026-10-28 22:28 ` Doug Smythies
2026-10-29 20:52 ` Rafael J. Wysocki (Intel)
2026-10-29 21:23 ` Zak Brighton Knight
2026-10-28 9:46 ` [PATCH v2] " Zak Brighton Knight
2026-10-28 15:52 ` Rafael J. Wysocki (Intel)
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to='001101dd6631$6167dbd0$24379370$@telus.net' \
--to=dsmythies@telus.net \
--cc=lenb@kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-pm@vger.kernel.org \
--cc=rafael@kernel.org \
--cc=srinivas.pandruvada@linux.intel.com \
--cc=stable@vger.kernel.org \
--cc=viresh.kumar@linaro.org \
--cc=zakbrightonknight@gmail.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.