From: "Ben Castricum" <helpdeskie@bencastricum.nl>
To: <linux-kernel@vger.kernel.org>
Subject: 2.6.5 Sensors & USB problems
Date: Tue, 6 Apr 2004 18:18:04 +0200 [thread overview]
Message-ID: <002b01c41bf2$bdae2a40$0502a8c0@tragebak> (raw)
Running the latest kernel has caused some problems for me since 2.6.4 up to
the current 2.6.5. I recompiled all interim releases and made a little
report of the troubles I run into. All kernels are compiled with gcc version
2.95.3 20010315 (release).
2.6.4 -> everything ok
2.6.5-rc1 -> sensors broke (ERROR: Can't get <sensor> data!)
2.6.5-rc2 -> USB broke (kernel NULL pointer dereference in khubd)
2.6.5-rc3 -> networking broke (real weird stuff)
2.6.5-final -> networking fixed again!
I am real glad that networking was fixed again, but this still leaves me
with the broken sensors and a non-functional USB Modem. This all happens on
a Asus-MEW main board with a Intel Celeron (Mendocino).
The sensor module I use are w83781d and i2c_i801 and sensor reports in the
first 2 lines
as99127f-i2c-0-2d
Adapter: SMBus I801 adapter at e800
Since 2.6.5-rc1 sensors reports "Can't get data!" for all sensors while all
modules are loaded normally.
For USB (already reported earlier on lkml) I get these message on startup
with 2.6.4:
drivers/usb/core/usb.c: registered new driver usbfs
drivers/usb/core/usb.c: registered new driver hub
USB Universal Host Controller Interface driver v2.2
uhci_hcd 0000:00:1f.2: UHCI Host Controller
PCI: Setting latency timer of device 0000:00:1f.2 to 64
uhci_hcd 0000:00:1f.2: irq 9, io base 0000a400
uhci_hcd 0000:00:1f.2: new USB bus registered, assigned bus number 1
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
drivers/usb/core/usb.c: registered new driver cdc_acm
drivers/usb/class/cdc-acm.c: v0.23:USB Abstract Control Model driver for USB
modems and ISDN adapters
hw_random hardware driver 1.0.0 loaded
usb 1-2: new full speed USB device using address 2
cdc_acm 1-2:1.0: ttyACM0: USB ACM device<6>8139too Fast Ethernet driver
0.9.27
and with 2.6.5-rc2 and up:
drivers/usb/core/usb.c: registered new driver usbfs
drivers/usb/core/usb.c: registered new driver hub
USB Universal Host Controller Interface driver v2.2
uhci_hcd 0000:00:1f.2: Intel Corp. 82801AA USB
PCI: Setting latency timer of device 0000:00:1f.2 to 64
uhci_hcd 0000:00:1f.2: irq 9, io base 0000a400
uhci_hcd 0000:00:1f.2: new USB bus registered, assigned bus number 1
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
drivers/usb/core/usb.c: registered new driver cdc_acm
drivers/usb/class/cdc-acm.c: v0.23:USB Abstract Control Model driver for USB
modems and ISDN adapters
hw_random hardware driver 1.0.0 loaded
usb 1-2: new full speed USB device using address 2
Unable to handle kernel NULL pointer dereference at virtual address 00000005
printing eip:
c8860954
*pde = 00000000
Oops: 0000 [#1]
PREEMPT
CPU: 0
EIP: 0060:[<c8860954>] Not tainted
EFLAGS: 00010246 (2.6.5-rc2)
EIP is at acm_probe+0x9c/0x51c [cdc_acm]
eax: c7ab3cc0 ebx: 00000000 ecx: c7da0ac0 edx: 00000000
esi: c76ccd6c edi: 00000004 ebp: c7ab3dc0 esp: c7b41e3c
ds: 007b es: 007b ss: 0068
Process khubd (pid: 37, threadinfo=c7b40000 task=c7b43760)
Stack: c8861d40 ffffffed c7ab3dd4 c7ab3dc0 c7a03580 c02908f0 00000000
00000001
c029a3cc c0173a7c c7a03580 c029a3e0 c7ab3cc0 c76ccd60 c769ac00
c888d049
c7ab3dc0 c8861c80 ffffffed c8861d40 c7ab3dd4 c769acd0 c8861d20
c01d06f1
Call Trace:
[<c0173a7c>] sysfs_add_file+0x5c/0x7c
[<c888d049>] usb_probe_interface+0x41/0x5c [usbcore]
[<c01d06f1>] bus_match+0x31/0x54
[<c01d076a>] device_attach+0x56/0x8c
[<c01d08e8>] bus_add_device+0x50/0x88
[<c01cfa48>] device_add+0x88/0x118
[<c01cfae9>] device_register+0x11/0x18
[<c8892653>] usb_set_configuration+0x1bb/0x1f4 [usbcore]
[<c888dd93>] usb_new_device+0x2d3/0x370 [usbcore]
[<c0117330>] printk+0x12c/0x154
[<c888f3c6>] hub_port_connect_change+0x1ce/0x254 [usbcore]
[<c888f57d>] hub_events+0x131/0x2dc [usbcore]
[<c888f755>] hub_thread+0x2d/0xe4 [usbcore]
[<c888f728>] hub_thread+0x0/0xe4 [usbcore]
[<c0113abc>] default_wake_function+0x0/0x1c
[<c0104e75>] kernel_thread_helper+0x5/0xc
Code: 80 7a 05 0a 0f 85 52 04 00 00 80 7a 04 01 0f 86 48 04 00 00
<6>8139too Fast Ethernet driver 0.9.27
as a bit if extra info, "lspci -v" gives me
root@gateway:~# lspci -v
00:00.0 Host bridge: Intel Corp. 82810 DC-100 GMCH [Graphics Memory
Controller Hub] (rev 02)
Subsystem: Asustek Computer, Inc.: Unknown device 8011
Flags: bus master, fast devsel, latency 0
00:01.0 VGA compatible controller: Intel Corp. 82810 DC-100 CGC [Chipset
Graphics Controller] (rev 02) (prog-if 00 [VGA])
Subsystem: Asustek Computer, Inc.: Unknown device 8011
Flags: bus master, 66Mhz, medium devsel, latency 0, IRQ 12
Memory at e6000000 (32-bit, prefetchable) [size=32M]
Memory at e5000000 (32-bit, non-prefetchable) [size=512K]
Capabilities: [dc] Power Management version 1
00:1e.0 PCI bridge: Intel Corp. 82801AA PCI Bridge (rev 01) (prog-if 00
[Normal decode])
Flags: bus master, fast devsel, latency 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
I/O behind bridge: 0000b000-0000dfff
Memory behind bridge: e4000000-e4ffffff
Prefetchable memory behind bridge: e5800000-e5ffffff
00:1f.0 ISA bridge: Intel Corp. 82801AA ISA Bridge (LPC) (rev 01)
Flags: bus master, medium devsel, latency 0
00:1f.1 IDE interface: Intel Corp. 82801AA IDE (rev 01) (prog-if 80
[Master])
Flags: bus master, medium devsel, latency 0
I/O ports at a800 [size=16]
00:1f.2 USB Controller: Intel Corp. 82801AA USB (rev 01) (prog-if 00 [UHCI])
Flags: bus master, medium devsel, latency 0, IRQ 9
I/O ports at a400 [size=32]
00:1f.3 SMBus: Intel Corp. 82801AA SMBus (rev 01)
Flags: medium devsel, IRQ 9
I/O ports at e800 [size=16]
00:1f.5 Multimedia audio controller: Intel Corp. 82801AA AC'97 Audio (rev
01)
Subsystem: Analog Devices: Unknown device 1043
Flags: bus master, medium devsel, latency 0, IRQ 9
I/O ports at e000 [size=256]
I/O ports at e100 [size=64]
01:08.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C
(rev 10)
Subsystem: Realtek Semiconductor Co., Ltd. RT8139
Flags: bus master, medium devsel, latency 64, IRQ 12
I/O ports at d800 [size=256]
Memory at e4800000 (32-bit, non-prefetchable) [size=256]
Capabilities: [50] Power Management version 2
01:09.0 Multimedia video controller: Brooktree Corporation Bt848 Video
Capture (rev 12)
Flags: bus master, medium devsel, latency 64, IRQ 9
Memory at e5800000 (32-bit, prefetchable) [disabled] [size=4K]
01:0a.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C
(rev 10)
Subsystem: Realtek Semiconductor Co., Ltd. RT8139
Flags: bus master, medium devsel, latency 64, IRQ 11
I/O ports at d400 [size=256]
Memory at e4000000 (32-bit, non-prefetchable) [size=256]
Capabilities: [50] Power Management version 2
01:0b.0 Multimedia audio controller: Creative Labs SB Live! EMU10k1 (rev 07)
Subsystem: Creative Labs SBLive! Player 5.1
Flags: bus master, medium devsel, latency 64, IRQ 9
I/O ports at d000 [disabled] [size=32]
Capabilities: [dc] Power Management version 1
01:0b.1 Input device controller: Creative Labs SB Live! MIDI/Game Port (rev
07)
Subsystem: Creative Labs Gameport Joystick
Flags: bus master, medium devsel, latency 64
I/O ports at b800 [disabled] [size=8]
Capabilities: [dc] Power Management version 1
I am happy to supply more information or do tests if needed.
Kind regards,
Ben Castricum
next reply other threads:[~2004-04-06 16:22 UTC|newest]
Thread overview: 8+ messages / expand[flat|nested] mbox.gz Atom feed top
2004-04-06 16:18 Ben Castricum [this message]
-- strict thread matches above, loose matches on Subject: below --
2004-04-07 14:56 2.6.5 Sensors & USB problems Jean Delvare
2004-04-17 22:07 ` Ian Morgan
2004-04-17 23:49 ` Ian Morgan
2004-04-18 5:51 ` Jean Delvare
2004-05-04 20:37 ` Greg KH
2004-05-06 17:41 ` Jean Delvare
2004-04-18 5:32 ` Jean Delvare
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to='002b01c41bf2$bdae2a40$0502a8c0@tragebak' \
--to=helpdeskie@bencastricum.nl \
--cc=linux-kernel@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.