From: "Doug Bazarnic" <kernel@bazarnic.net>
To: <linux-kernel@vger.kernel.org>
Subject: e1000 tx Unit hang on 2.6.28 and patch that works...
Date: Fri, 9 Jan 2009 14:47:23 -0700 [thread overview]
Message-ID: <007e01c972a3$db2301b0$91690510$@net> (raw)
Asus P5k, Intel Q9450, 8gb ram, x86_64, running 2.6.28. The on board eth0
atl1 never has a problem, only eth1 intel e1000, plugged into a pci slot.
On a couple of machines, the way I got it to stop, was to use 8.0.6 intel
e1000 driver with the patch below. (works on same hardware, running 2.6.27
kernels)
I can’t remember where I downloaded this patch from, but I haven’t had an
issue yet with it.
[root@web6 SCRIPTS]# cat e1000-8-0-6-stepfix.patch
>diff -up e1000-8-0-6base/src/e1000_main.c
e1000-8-0-6stepfix/src/e1000_main.c
>--- e1000-8-0-6base/src/e1000_main.c 2008-10-29 17:38:38.000000000 -0700
>+++ e1000-8-0-6stepfix/src/e1000_main.c 2008-10-29 17:43:52.000000000 -0700
>@@ -65,7 +65,7 @@ static char e1000_driver_string[] = "Int
>
> #define DRV_HW_PERF
>
>-#define DRV_VERSION "8.0.6" DRV_NAPI DRV_DEBUG DRV_HW_PERF
>+#define DRV_VERSION "8.0.6a" DRV_NAPI DRV_DEBUG DRV_HW_PERF
> const char e1000_driver_version[] = DRV_VERSION;
> static const char e1000_copyright[] = "Copyright (c) 1999-2008 Intel
Corporation.";
>
>@@ -2364,8 +2364,8 @@ link_up:
> if (!netif_carrier_ok(netdev)) {
> for (i = 0 ; i < adapter->num_tx_queues ; i++) {
> tx_ring = &adapter->tx_ring[i];
>- tx_pending |= (E1000_DESC_UNUSED(tx_ring) + 1 <
>-
tx_ring->count);
>+ tx_pending |= (E1000_DESC_UNUSED(tx_ring) +
>+ tx_ring->step < tx_ring->count);
> }
> if (tx_pending) {
> /* We've lost link, so the controller stops DMA,
>@@ -2892,7 +2892,7 @@ static int __e1000_maybe_stop_tx(struct
>
> /* We need to check again in a case another CPU has just
> * made room available. */
>- if (likely(E1000_DESC_UNUSED(tx_ring) < size))
>+ if (likely(E1000_DESC_UNUSED(tx_ring) < ((size) * tx_ring->step)))
> return -EBUSY;
>
> /* A reprieve! */
>@@ -2909,7 +2909,7 @@ static int __e1000_maybe_stop_tx(struct
> static int e1000_maybe_stop_tx(struct net_device *netdev,
> struct e1000_tx_ring *tx_ring, int size)
> {
>- if (likely(E1000_DESC_UNUSED(tx_ring) >= size))
>+ if (likely(E1000_DESC_UNUSED(tx_ring) >= ((size) * tx_ring->step)))
> return 0;
> return __e1000_maybe_stop_tx(netdev, tx_ring, size);
> }
---------------------------------
This has been an ongoing problem on over 20 identical machines.
Jan 7 13:26:41 web2 kernel: e1000: eth1: e1000_clean_tx_irq: Detected Tx
Unit Hang
Jan 7 13:26:41 web2 kernel: Tx Queue <0>
Jan 7 13:26:41 web2 kernel: TDH <2a>
Jan 7 13:26:41 web2 kernel: TDT <2d>
Jan 7 13:26:41 web2 kernel: next_to_use <2d>
Jan 7 13:26:41 web2 kernel: next_to_clean <2a>
Jan 7 13:26:41 web2 kernel: buffer_info[next_to_clean]
Jan 7 13:26:41 web2 kernel: time_stamp <103105c76>
Jan 7 13:26:41 web2 kernel: next_to_watch <2a>
Jan 7 13:26:41 web2 kernel: jiffies <103106770>
Jan 7 13:26:41 web2 kernel: next_to_watch.status <0>
Jan 7 13:26:43 web2 kernel: e1000: eth1: e1000_clean_tx_irq: Detected Tx
Unit Hang
Jan 7 13:26:43 web2 kernel: Tx Queue <0>
Jan 7 13:26:43 web2 kernel: TDH <2a>
Jan 7 13:26:43 web2 kernel: TDT <2d>
Jan 7 13:26:43 web2 kernel: next_to_use <2d>
Jan 7 13:26:43 web2 kernel: next_to_clean <2a>
Jan 7 13:26:43 web2 kernel: buffer_info[next_to_clean]
Jan 7 13:26:43 web2 kernel: time_stamp <103105c76>
Jan 7 13:26:43 web2 kernel: next_to_watch <2a>
Jan 7 13:26:43 web2 kernel: jiffies <103106f41>
Jan 7 13:26:43 web2 kernel: next_to_watch.status <0>
Jan 7 13:26:45 web2 kernel: e1000: eth1: e1000_clean_tx_irq: Detected Tx
Unit Hang
Jan 7 13:26:45 web2 kernel: Tx Queue <0>
Jan 7 13:26:45 web2 kernel: TDH <2a>
Jan 7 13:26:45 web2 kernel: TDT <2d>
Jan 7 13:26:45 web2 kernel: next_to_use <2d>
Jan 7 13:26:45 web2 kernel: next_to_clean <2a>
Jan 7 13:26:45 web2 kernel: buffer_info[next_to_clean]
Jan 7 13:26:45 web2 kernel: time_stamp <103105c76>
Jan 7 13:26:45 web2 kernel: next_to_watch <2a>
Jan 7 13:26:45 web2 kernel: jiffies <103107711>
Jan 7 13:26:45 web2 kernel: next_to_watch.status <0>
Jan 7 13:26:47 web2 kernel: ------------[ cut here ]------------
Jan 7 13:26:47 web2 kernel: WARNING: at net/sched/sch_generic.c:226
dev_watchdog+0x206/0x220()
Jan 7 13:26:47 web2 kernel: NETDEV WATCHDOG: eth1 (e1000): transmit timed
out
Jan 7 13:26:47 web2 kernel: Modules linked in: nfs lockd nfs_acl sunrpc
dm_mirror dm_region_hash dm_log dm_multipath dm_mod serio_raw e1000
pata_jmicron pcspkr
Jan 7 13:26:47 web2 kernel: Pid: 0, comm: swapper Not tainted 2.6.28 #1
Jan 7 13:26:47 web2 kernel: Call Trace:
Jan 7 13:26:47 web2 kernel: <IRQ> [<ffffffff802361fc>]
warn_slowpath+0x10c/0x150
Jan 7 13:26:47 web2 kernel: [<ffffffff8022f4c1>]
enqueue_task_fair+0xf1/0x110
Jan 7 13:26:47 web2 kernel: [<ffffffff8022c217>] source_load+0x37/0x70
Jan 7 13:26:47 web2 kernel: [<ffffffff803c9a6a>] __next_cpu+0x1a/0x30
Jan 7 13:26:47 web2 kernel: [<ffffffff8022d99c>]
find_busiest_group+0x18c/0x820
Jan 7 13:26:47 web2 kernel: [<ffffffff802116c9>] read_tsc+0x9/0x20
Jan 7 13:26:47 web2 kernel: [<ffffffff8024fc71>] getnstimeofday+0x41/0xc0
Jan 7 13:26:47 web2 kernel: [<ffffffff803cf20e>] strlcpy+0x4e/0x80
Jan 7 13:26:47 web2 kernel: [<ffffffff80532cd6>] dev_watchdog+0x206/0x220
Jan 7 13:26:47 web2 kernel: [<ffffffff802116c9>] read_tsc+0x9/0x20
Jan 7 13:26:47 web2 kernel: [<ffffffff8024fc71>] getnstimeofday+0x41/0xc0
Jan 7 13:26:47 web2 kernel: [<ffffffff80532ad0>] dev_watchdog+0x0/0x220
Jan 7 13:26:47 web2 kernel: [<ffffffff8023fadf>]
run_timer_softirq+0x15f/0x1c0
Jan 7 13:26:47 web2 kernel: [<ffffffff8021b165>]
lapic_next_event+0x15/0x20
Jan 7 13:26:47 web2 kernel: [<ffffffff8023b40c>] __do_softirq+0x9c/0x170
Jan 7 13:26:47 web2 kernel: [<ffffffff8020c87c>] call_softirq+0x1c/0x30
Jan 7 13:26:47 web2 kernel: [<ffffffff8020d975>] do_softirq+0x35/0x70
Jan 7 13:26:47 web2 kernel: [<ffffffff8021bb05>]
smp_apic_timer_interrupt+0x85/0xd0
Jan 7 13:26:47 web2 kernel: [<ffffffff8020c2cb>]
apic_timer_interrupt+0x6b/0x70
Jan 7 13:26:47 web2 kernel: <EOI> [<ffffffff80212511>]
mwait_idle+0x41/0x50
Jan 7 13:26:47 web2 kernel: [<ffffffff8020a2da>] cpu_idle+0x3a/0x70
Jan 7 13:26:47 web2 kernel: ---[ end trace 06fe492fa8302a12 ]---
Jan 7 13:26:50 web2 kernel: e1000: eth1: e1000_watchdog: NIC Link is Up
1000 Mbps Full Duplex, Flow Control: RX/TX
00:00.0 Host bridge: Intel Corporation 82G33/G31/P35/P31 Express DRAM
Controller (rev 02)
Subsystem: ASUSTeK Computer Inc. Unknown device 8276
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort+ >SERR- <PERR-
Latency: 0
Capabilities: [e0] Vendor Specific Information
00:02.0 VGA compatible controller: Intel Corporation 82G33/G31 Express
Integrated Graphics Controller (rev 02) (prog-if 00 [VGA])
Subsystem: ASUSTeK Computer Inc. Unknown device 8276
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 11
Region 0: Memory at fe800000 (32-bit, non-prefetchable) [size=512K]
Region 1: I/O ports at cc00 [size=8]
Region 2: Memory at d0000000 (32-bit, prefetchable) [size=256M]
Region 3: Memory at fe700000 (32-bit, non-prefetchable) [size=1M]
Capabilities: [90] Message Signalled Interrupts: 64bit- Queue=0/0
Enable-
Address: 00000000 Data: 0000
Capabilities: [d0] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:02.1 Display controller: Intel Corporation 82G33/G31 Express Integrated
Graphics Controller (rev 02)
Subsystem: ASUSTeK Computer Inc. Unknown device 8276
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Region 0: Memory at fe880000 (32-bit, non-prefetchable) [size=512K]
Capabilities: [d0] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:1c.0 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port
1 (rev 02) (prog-if 00 [Normal decode])
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: fff00000-000fffff
Prefetchable memory behind bridge: 00000000fdf00000-00000000fdf00000
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [40] Express Root Port (Slot+) IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0,
ExtTag-
Device: Latency L0s <64ns, L1 <1us
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x4, ASPM L0s L1, Port 1
Link: Latency L0s <1us, L1 <4us
Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x0
Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug+
Surpise+
Slot: Number 0, PowerLimit 10.000000
Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
Slot: AttnInd Unknown, PwrInd Unknown, Power-
Root: Correctable- Non-Fatal- Fatal- PME-
Capabilities: [80] Message Signalled Interrupts: 64bit- Queue=0/0
Enable+
Address: fee0f00c Data: 4159
Capabilities: [90] #0d [0000]
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [100] Virtual Channel
Capabilities: [180] Unknown (5)
00:1c.4 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port
5 (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: fea00000-feafffff
Prefetchable memory behind bridge: 00000000fff00000-0000000000000000
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [40] Express Root Port (Slot+) IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0,
ExtTag-
Device: Latency L0s <64ns, L1 <1us
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 5
Link: Latency L0s <256ns, L1 <4us
Link: ASPM Disabled RCB 64 bytes CommClk+ ExtSynch-
Link: Speed 2.5Gb/s, Width x1
Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug+
Surpise+
Slot: Number 0, PowerLimit 10.000000
Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
Slot: AttnInd Unknown, PwrInd Unknown, Power-
Root: Correctable- Non-Fatal- Fatal- PME-
Capabilities: [80] Message Signalled Interrupts: 64bit- Queue=0/0
Enable+
Address: fee0f00c Data: 4161
Capabilities: [90] #0d [0000]
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [100] Virtual Channel
Capabilities: [180] Unknown (5)
00:1c.5 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port
6 (rev 02) (prog-if 00 [Normal decode])
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: fe900000-fe9fffff
Prefetchable memory behind bridge: 00000000fff00000-0000000000000000
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [40] Express Root Port (Slot+) IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0,
ExtTag-
Device: Latency L0s <64ns, L1 <1us
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 6
Link: Latency L0s <256ns, L1 <4us
Link: ASPM Disabled RCB 64 bytes CommClk+ ExtSynch-
Link: Speed 2.5Gb/s, Width x1
Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug+
Surpise+
Slot: Number 0, PowerLimit 10.000000
Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
Slot: AttnInd Unknown, PwrInd Unknown, Power-
Root: Correctable- Non-Fatal- Fatal- PME-
Capabilities: [80] Message Signalled Interrupts: 64bit- Queue=0/0
Enable+
Address: fee0f00c Data: 4169
Capabilities: [90] #0d [0000]
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [100] Virtual Channel
Capabilities: [180] Unknown (5)
00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev 92) (prog-if 01
[Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=04, subordinate=04, sec-latency=32
I/O behind bridge: 0000e000-0000efff
Memory behind bridge: feb00000-febfffff
Prefetchable memory behind bridge: 00000000f0000000-00000000f0000000
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [50] #0d [0000]
00:1f.0 ISA bridge: Intel Corporation 82801IB (ICH9) LPC Interface
Controller (rev 02)
Subsystem: ASUSTeK Computer Inc. Unknown device 8277
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Capabilities: [e0] Vendor Specific Information
00:1f.2 IDE interface: Intel Corporation 82801IB (ICH9) 2 port SATA IDE
Controller (rev 02) (prog-if 8f [Master SecP SecO PriP PriO])
Subsystem: ASUSTeK Computer Inc. Unknown device 8277
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 22
Region 0: I/O ports at b880 [size=8]
Region 1: I/O ports at b800 [size=4]
Region 2: I/O ports at b480 [size=8]
Region 3: I/O ports at b400 [size=4]
Region 4: I/O ports at b080 [size=16]
Region 5: I/O ports at b000 [size=16]
Capabilities: [70] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [b0] Vendor Specific Information
00:1f.3 SMBus: Intel Corporation 82801I (ICH9 Family) SMBus Controller (rev
02)
Subsystem: ASUSTeK Computer Inc. Unknown device 8277
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin C routed to IRQ 5
Region 0: Memory at fe6fbc00 (64-bit, non-prefetchable) [size=256]
Region 4: I/O ports at 0400 [size=32]
00:1f.5 IDE interface: Intel Corporation 82801I (ICH9 Family) 2 port SATA
IDE Controller (rev 02) (prog-if 85 [Master SecO PriO])
Subsystem: ASUSTeK Computer Inc. Unknown device 8277
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 22
Region 0: I/O ports at c880 [size=8]
Region 1: I/O ports at c800 [size=4]
Region 2: I/O ports at c480 [size=8]
Region 3: I/O ports at c400 [size=4]
Region 4: I/O ports at c080 [size=16]
Region 5: I/O ports at c000 [size=16]
Capabilities: [70] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [b0] Vendor Specific Information
01:00.0 Ethernet controller: Attansic Technology Corp. L1 Gigabit Ethernet
Adapter (rev b0)
Subsystem: ASUSTeK Computer Inc. Unknown device 8226
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 27
Region 0: Memory at fe9c0000 (64-bit, non-prefetchable) [size=256K]
Expansion ROM at fe9a0000 [disabled] [size=128K]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [48] Message Signalled Interrupts: 64bit+ Queue=0/0
Enable+
Address: 00000000fee0200c Data: 4179
Capabilities: [58] Express Endpoint IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0,
ExtTag-
Device: Latency L0s <4us, L1 unlimited
Device: AtnBtn+ AtnInd+ PwrInd+
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 512 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s, Port 0
Link: Latency L0s unlimited, L1 unlimited
Link: ASPM Disabled RCB 64 bytes CommClk+ ExtSynch-
Link: Speed 2.5Gb/s, Width x1
Capabilities: [100] Advanced Error Reporting
02:00.0 SATA controller: JMicron Technologies, Inc. JMicron 20360/20363 AHCI
Controller (rev 03) (prog-if 01 [AHCI 1.0])
Subsystem: ASUSTeK Computer Inc. Unknown device 824f
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 16
Region 5: Memory at feafe000 (32-bit, non-prefetchable) [size=8K]
Expansion ROM at feae0000 [disabled] [size=64K]
Capabilities: [68] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] Express Legacy Endpoint IRQ 1
Device: Supported: MaxPayload 128 bytes, PhantFunc 0,
ExtTag-
Device: Latency L0s <64ns, L1 <1us
Device: AtnBtn- AtnInd- PwrInd-
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 512 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s, Port 1
Link: Latency L0s <1us, L1 <16us
Link: ASPM Disabled RCB 64 bytes CommClk+ ExtSynch-
Link: Speed 2.5Gb/s, Width x1
02:00.1 IDE interface: JMicron Technologies, Inc. JMicron 20360/20363 AHCI
Controller (rev 03) (prog-if 85 [Master SecO PriO])
Subsystem: ASUSTeK Computer Inc. Unknown device 824f
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 17
Region 0: I/O ports at dc00 [size=8]
Region 1: I/O ports at d880 [size=4]
Region 2: I/O ports at d800 [size=8]
Region 3: I/O ports at d480 [size=4]
Region 4: I/O ports at d400 [size=16]
Capabilities: [68] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
04:01.0 Ethernet controller: Intel Corporation 82541PI Gigabit Ethernet
Controller (rev 05)
Subsystem: Intel Corporation PRO/1000 GT Desktop Adapter
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (63750ns min), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 17
Region 0: Memory at febe0000 (32-bit, non-prefetchable) [size=128K]
Region 1: Memory at febc0000 (32-bit, non-prefetchable) [size=128K]
Region 2: I/O ports at ec00 [size=64]
Expansion ROM at f0000000 [disabled] [size=128K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [e4] PCI-X non-bridge device
Command: DPERE- ERO+ RBC=512 OST=1
Status: Dev=00:00.0 64bit- 133MHz- SCD- USC- DC=simple
DMMRBC=2048 DMOST=1 DMCRS=8 RSCEM- 266MHz- 533MHz-
Doug Bazarnic
next reply other threads:[~2009-01-09 21:47 UTC|newest]
Thread overview: 2+ messages / expand[flat|nested] mbox.gz Atom feed top
2009-01-09 21:47 Doug Bazarnic [this message]
2009-01-12 18:27 ` e1000 tx Unit hang on 2.6.28 and patch that works Jeff Kirsher
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to='007e01c972a3$db2301b0$91690510$@net' \
--to=kernel@bazarnic.net \
--cc=linux-kernel@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.