From: Hubert Tonneau <hubert.tonneau@fullpliant.org>
To: linux-kernel@vger.kernel.org
Subject: Re: Linux 2.6 no boot report
Date: Thu, 11 Mar 2004 17:30:34 GMT [thread overview]
Message-ID: <043MZAY12@server5.heliogroup.fr> (raw)
On Thu, Mar 11, 2004 at 04:32:31PM +0000, Hubert Tonneau wrote:
> I've successfully run Linux kernel 2.6 on several boxes, with the excepti> on
> of the Dell PowerEdge 2600:
> The box is:
> . dual Xeon
> . Fusion SCSI controler
> . root partition is software RAID 1
> . Intel pro 1000 ethernet
>
> It fails with all 2.6 kernel I tried, including the fresh 2.6.4
> No error message at all, the machine just freezes after displaying network
> protocols and before displaying VFS root mounting message.
You might be interested with these lines that appear in the 2.4.25 boot
sequence near the place where 2.6 freezes:
<4>SCSI Error: (0:0:0) Status=02h (CHECK CONDITION)
<4> Key=6h (UNIT ATTENTION); FRU=00h
<4> ASC/ASCQ=29h/02h "SCSI BUS RESET OCCURRED"
<4> CDB: 2A 00 11 17 5D BF 00 00 08 00
<4>
Here is the 2.4.25 full boot sequence:
<4>Linux version 2.4.25 (root@sx270) (gcc version 2.95.4 20011002 (Debian prerelease)) #1 SMP Thu Mar 11 17:43:06 CET 2004
<6>BIOS-provided physical RAM map:
<4> BIOS-e820: 0000000000000000 - 00000000000a0000 (usable)
<4> BIOS-e820: 0000000000100000 - 000000007ffe0000 (usable)
<4> BIOS-e820: 000000007ffe0000 - 000000007ffefc00 (ACPI data)
<4> BIOS-e820: 000000007ffefc00 - 000000007ffff000 (reserved)
<4> BIOS-e820: 00000000fec00000 - 00000000fec90000 (reserved)
<4> BIOS-e820: 00000000fee00000 - 00000000fee10000 (reserved)
<4> BIOS-e820: 00000000ffb00000 - 0000000100000000 (reserved)
<5>1151MB HIGHMEM available.
<5>896MB LOWMEM available.
<4>found SMP MP-table at 000fe710
<4>hm, page 000fe000 reserved twice.
<4>hm, page 000ff000 reserved twice.
<4>hm, page 000f0000 reserved twice.
<4>On node 0 totalpages: 524256
<4>zone(0): 4096 pages.
<4>zone(1): 225280 pages.
<4>zone(2): 294880 pages.
<6>ACPI: RSDP (v000 DELL ) @ 0x000fdc20
<6>ACPI: RSDT (v001 DELL PE2600 0x00000001 MSFT 0x0100000a) @ 0x000fdc34
<6>ACPI: FADT (v001 DELL PE2600 0x00000001 MSFT 0x0100000a) @ 0x000fdc64
<6>ACPI: MADT (v001 DELL PE2600 0x00000001 MSFT 0x0100000a) @ 0x000fdcd8
<6>ACPI: SPCR (v001 DELL PE2600 0x00000001 MSFT 0x0100000a) @ 0x000fdd96
<6>ACPI: DSDT (v001 DELL PE2600 0x00000001 MSFT 0x0100000a) @ 0x00000000
<6>ACPI: Local APIC address 0xfee00000
<6>ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
<4>Processor #0 Pentium 4(tm) XEON(tm) APIC version 20
<6>ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] enabled)
<4>Processor #2 Pentium 4(tm) XEON(tm) APIC version 20
<6>ACPI: LAPIC (acpi_id[0x03] lapic_id[0x01] enabled)
<4>Processor #1 Pentium 4(tm) XEON(tm) APIC version 20
<6>ACPI: LAPIC (acpi_id[0x04] lapic_id[0x03] enabled)
<4>Processor #3 Pentium 4(tm) XEON(tm) APIC version 20
<6>ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
<6>ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1])
<6>ACPI: LAPIC_NMI (acpi_id[0x03] high edge lint[0x1])
<6>ACPI: LAPIC_NMI (acpi_id[0x04] high edge lint[0x1])
<6>Using ACPI for processor (LAPIC) configuration information
<4>Intel MultiProcessor Specification v1.4
<4> Virtual Wire compatibility mode.
<4>OEM ID: DELL Product ID: PE 0123 APIC at: 0xFEE00000
<4>I/O APIC #4 Version 32 at 0xFEC00000.
<4>I/O APIC #5 Version 32 at 0xFEC80000.
<4>I/O APIC #6 Version 32 at 0xFEC81000.
<4>I/O APIC #7 Version 32 at 0xFEC82000.
<4>I/O APIC #8 Version 32 at 0xFEC82800.
<4>Enabling APIC mode: Flat. Using 5 I/O APICs
<4>Processors: 4
<4>Kernel command line: BOOT_IMAGE=recover ro root=900
<6>Initializing CPU#0
<4>Detected 2791.809 MHz processor.
<4>Console: colour VGA+ 80x25
<4>Calibrating delay loop... 5570.56 BogoMIPS
<6>Memory: 2070128k/2097024k available (1125k kernel code, 26512k reserved, 295k data, 112k init, 1179520k highmem)
<6>Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
<6>Inode cache hash table entries: 131072 (order: 8, 1048576 bytes)
<6>Mount cache hash table entries: 512 (order: 0, 4096 bytes)
<6>Buffer cache hash table entries: 131072 (order: 7, 524288 bytes)
<4>Page-cache hash table entries: 524288 (order: 9, 2097152 bytes)
<6>CPU: Trace cache: 12K uops, L1 D cache: 8K
<6>CPU: L2 cache: 512K
<6>CPU: Physical Processor ID: 0
<6>Intel machine check architecture supported.
<6>Intel machine check reporting enabled on CPU#0.
<7>CPU: After generic, caps: bfebfbff 00000000 00000000 00000000
<7>CPU: Common caps: bfebfbff 00000000 00000000 00000000
<6>Enabling fast FPU save and restore... done.
<6>Enabling unmasked SIMD FPU exception support... done.
<6>Checking 'hlt' instruction... OK.
<4>POSIX conformance testing by UNIFIX
<4>mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au)
<4>mtrr: detected mtrr type: Intel
<6>CPU: Trace cache: 12K uops, L1 D cache: 8K
<6>CPU: L2 cache: 512K
<6>CPU: Physical Processor ID: 0
<6>Intel machine check reporting enabled on CPU#0.
<7>CPU: After generic, caps: bfebfbff 00000000 00000000 00000000
<7>CPU: Common caps: bfebfbff 00000000 00000000 00000000
<4>CPU0: Intel(R) Xeon(TM) CPU 2.80GHz stepping 07
<4>per-CPU timeslice cutoff: 1463.07 usecs.
<4>enabled ExtINT on CPU#0
<4>ESR value before enabling vector: 00000040
<4>ESR value after enabling vector: 00000000
<4>Booting processor 1/1 eip 2000
<6>Initializing CPU#1
<4>masked ExtINT on CPU#1
<4>ESR value before enabling vector: 00000000
<4>ESR value after enabling vector: 00000000
<4>Calibrating delay loop... 5570.56 BogoMIPS
<6>CPU: Trace cache: 12K uops, L1 D cache: 8K
<6>CPU: L2 cache: 512K
<6>CPU: Physical Processor ID: 0
<6>Intel machine check reporting enabled on CPU#1.
<7>CPU: After generic, caps: bfebfbff 00000000 00000000 00000000
<7>CPU: Common caps: bfebfbff 00000000 00000000 00000000
<4>CPU1: Intel(R) Xeon(TM) CPU 2.80GHz stepping 07
<4>Booting processor 2/2 eip 2000
<6>Initializing CPU#2
<4>masked ExtINT on CPU#2
<4>ESR value before enabling vector: 00000000
<4>ESR value after enabling vector: 00000000
<4>Calibrating delay loop... 5583.66 BogoMIPS
<6>CPU: Trace cache: 12K uops, L1 D cache: 8K
<6>CPU: L2 cache: 512K
<6>CPU: Physical Processor ID: 3
<6>Intel machine check reporting enabled on CPU#2.
<7>CPU: After generic, caps: bfebfbff 00000000 00000000 00000000
<7>CPU: Common caps: bfebfbff 00000000 00000000 00000000
<4>CPU2: Intel(R) Xeon(TM) CPU 2.80GHz stepping 07
<4>Booting processor 3/3 eip 2000
<6>Initializing CPU#3
<4>masked ExtINT on CPU#3
<4>ESR value before enabling vector: 00000000
<4>ESR value after enabling vector: 00000000
<4>Calibrating delay loop... 5570.56 BogoMIPS
<6>CPU: Trace cache: 12K uops, L1 D cache: 8K
<6>CPU: L2 cache: 512K
<6>CPU: Physical Processor ID: 3
<6>Intel machine check reporting enabled on CPU#3.
<7>CPU: After generic, caps: bfebfbff 00000000 00000000 00000000
<7>CPU: Common caps: bfebfbff 00000000 00000000 00000000
<4>CPU3: Intel(R) Xeon(TM) CPU 2.80GHz stepping 07
<6>Total of 4 processors activated (22295.34 BogoMIPS).
<4>cpu_sibling_map[0] = 1
<4>cpu_sibling_map[1] = 0
<4>cpu_sibling_map[2] = 3
<4>cpu_sibling_map[3] = 2
<4>ENABLING IO-APIC IRQs
<4>Setting 4 in the phys_id_present_map
<6>...changing IO-APIC physical APIC ID to 4 ... ok.
<4>Setting 5 in the phys_id_present_map
<6>...changing IO-APIC physical APIC ID to 5 ... ok.
<4>Setting 6 in the phys_id_present_map
<6>...changing IO-APIC physical APIC ID to 6 ... ok.
<4>Setting 7 in the phys_id_present_map
<6>...changing IO-APIC physical APIC ID to 7 ... ok.
<4>Setting 8 in the phys_id_present_map
<6>...changing IO-APIC physical APIC ID to 8 ... ok.
<7>init IO_APIC IRQs
<7> IO-APIC (apicid-pin) 4-0, 4-5, 4-11, 4-13, 4-21, 4-22, 4-23, 5-5, 5-6, 5-7, 5-8, 5-9, 5-10, 5-11, 5-12, 5-13, 5-14, 5-15, 5-16, 5-17, 5-18, 5-19, 5-20, 5-21, 5-22, 5-23, 6-12, 6-13, 6-14, 6-15, 6-16, 6-17, 6-18, 6-19, 6-20, 6-21, 6-22, 6-23, 7-2, 7-3, 7-4, 7-5, 7-6, 7-7, 7-8, 7-9, 7-10, 7-11, 7-12, 7-13, 7-14, 7-15, 7-16, 7-17, 7-18, 7-19, 7-20, 7-21, 7-22, 7-23, 8-8, 8-9, 8-10, 8-11, 8-12, 8-13, 8-14, 8-15, 8-16, 8-17, 8-18, 8-19, 8-20, 8-21, 8-22, 8-23 not connected.
<6>..TIMER: vector=0x31 pin1=2 pin2=0
<7>number of MP IRQ sources: 53.
<7>number of IO-APIC #4 registers: 24.
<7>number of IO-APIC #5 registers: 24.
<7>number of IO-APIC #6 registers: 24.
<7>number of IO-APIC #7 registers: 24.
<7>number of IO-APIC #8 registers: 24.
<6>testing the IO APIC.......................
<4>
<7>IO APIC #4......
<7>.... register #00: 04000000
<7>....... : physical APIC id: 04
<7>....... : Delivery Type: 0
<7>....... : LTS : 0
<7>.... register #01: 00178020
<7>....... : max redirection entries: 0017
<7>....... : PRQ implemented: 1
<7>....... : IO APIC version: 0020
<7>.... register #02: 00000000
<7>....... : arbitration: 00
<7>.... register #03: 00000001
<7>....... : Boot DT : 1
<7>.... IRQ redirection table:
<7> NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
<7> 00 000 00 1 0 0 0 0 0 0 00
<7> 01 00F 0F 0 0 0 0 0 1 1 39
<7> 02 00F 0F 0 0 0 0 0 1 1 31
<7> 03 00F 0F 0 0 0 0 0 1 1 41
<7> 04 00F 0F 0 0 0 0 0 1 1 49
<7> 05 000 00 1 0 0 0 0 0 0 00
<7> 06 00F 0F 0 0 0 0 0 1 1 51
<7> 07 00F 0F 0 0 0 0 0 1 1 59
<7> 08 00F 0F 0 0 0 0 0 1 1 61
<7> 09 00F 0F 0 0 0 0 0 1 1 69
<7> 0a 00F 0F 0 0 0 0 0 1 1 71
<7> 0b 000 00 1 0 0 0 0 0 0 00
<7> 0c 00F 0F 0 0 0 0 0 1 1 79
<7> 0d 000 00 1 0 0 0 0 0 0 00
<7> 0e 00F 0F 0 0 0 0 0 1 1 81
<7> 0f 00F 0F 0 0 0 0 0 1 1 89
<7> 10 00F 0F 1 1 0 1 0 1 1 91
<7> 11 00F 0F 1 1 0 1 0 1 1 99
<7> 12 00F 0F 1 1 0 1 0 1 1 A1
<7> 13 00F 0F 1 1 0 1 0 1 1 A9
<7> 14 00F 0F 1 1 0 1 0 1 1 B1
<7> 15 000 00 1 0 0 0 0 0 0 00
<7> 16 000 00 1 0 0 0 0 0 0 00
<7> 17 000 00 1 0 0 0 0 0 0 00
<4>
<7>IO APIC #5......
<7>.... register #00: 05000000
<7>....... : physical APIC id: 05
<7>....... : Delivery Type: 0
<7>....... : LTS : 0
<7>.... register #01: 00178020
<7>....... : max redirection entries: 0017
<7>....... : PRQ implemented: 1
<7>....... : IO APIC version: 0020
<7>.... register #02: 05000000
<7>....... : arbitration: 05
<7>.... register #03: 00000001
<7>....... : Boot DT : 1
<7>.... IRQ redirection table:
<7> NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
<7> 00 00F 0F 1 1 0 1 0 1 1 B9
<7> 01 00F 0F 1 1 0 1 0 1 1 C1
<7> 02 00F 0F 1 1 0 1 0 1 1 C9
<7> 03 00F 0F 1 1 0 1 0 1 1 D1
<7> 04 00F 0F 1 1 0 1 0 1 1 D9
<7> 05 000 00 1 0 0 0 0 0 0 00
<7> 06 000 00 1 0 0 0 0 0 0 00
<7> 07 000 00 1 0 0 0 0 0 0 00
<7> 08 000 00 1 0 0 0 0 0 0 00
<7> 09 000 00 1 0 0 0 0 0 0 00
<7> 0a 000 00 1 0 0 0 0 0 0 00
<7> 0b 000 00 1 0 0 0 0 0 0 00
<7> 0c 000 00 1 0 0 0 0 0 0 00
<7> 0d 000 00 1 0 0 0 0 0 0 00
<7> 0e 000 00 1 0 0 0 0 0 0 00
<7> 0f 000 00 1 0 0 0 0 0 0 00
<7> 10 000 00 1 0 0 0 0 0 0 00
<7> 11 000 00 1 0 0 0 0 0 0 00
<7> 12 000 00 1 0 0 0 0 0 0 00
<7> 13 000 00 1 0 0 0 0 0 0 00
<7> 14 000 00 1 0 0 0 0 0 0 00
<7> 15 000 00 1 0 0 0 0 0 0 00
<7> 16 000 00 1 0 0 0 0 0 0 00
<7> 17 000 00 1 0 0 0 0 0 0 00
<4>
<7>IO APIC #6......
<7>.... register #00: 06000000
<7>....... : physical APIC id: 06
<7>....... : Delivery Type: 0
<7>....... : LTS : 0
<7>.... register #01: 00178020
<7>....... : max redirection entries: 0017
<7>....... : PRQ implemented: 1
<7>....... : IO APIC version: 0020
<7>.... register #02: 06000000
<7>....... : arbitration: 06
<7>.... register #03: 00000001
<7>....... : Boot DT : 1
<7>.... IRQ redirection table:
<7> NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
<7> 00 00F 0F 1 1 0 1 0 1 1 E1
<7> 01 00F 0F 1 1 0 1 0 1 1 E9
<7> 02 00F 0F 1 1 0 1 0 1 1 32
<7> 03 00F 0F 1 1 0 1 0 1 1 3A
<7> 04 00F 0F 1 1 0 1 0 1 1 42
<7> 05 00F 0F 1 1 0 1 0 1 1 4A
<7> 06 00F 0F 1 1 0 1 0 1 1 52
<7> 07 00F 0F 1 1 0 1 0 1 1 5A
<7> 08 00F 0F 1 1 0 1 0 1 1 62
<7> 09 00F 0F 1 1 0 1 0 1 1 6A
<7> 0a 00F 0F 1 1 0 1 0 1 1 72
<7> 0b 00F 0F 1 1 0 1 0 1 1 7A
<7> 0c 000 00 1 0 0 0 0 0 0 00
<7> 0d 000 00 1 0 0 0 0 0 0 00
<7> 0e 000 00 1 0 0 0 0 0 0 00
<7> 0f 000 00 1 0 0 0 0 0 0 00
<7> 10 000 00 1 0 0 0 0 0 0 00
<7> 11 000 00 1 0 0 0 0 0 0 00
<7> 12 000 00 1 0 0 0 0 0 0 00
<7> 13 000 00 1 0 0 0 0 0 0 00
<7> 14 000 00 1 0 0 0 0 0 0 00
<7> 15 000 00 1 0 0 0 0 0 0 00
<7> 16 000 00 1 0 0 0 0 0 0 00
<7> 17 000 00 1 0 0 0 0 0 0 00
<4>
<7>IO APIC #7......
<7>.... register #00: 07000000
<7>....... : physical APIC id: 07
<7>....... : Delivery Type: 0
<7>....... : LTS : 0
<7>.... register #01: 00178020
<7>....... : max redirection entries: 0017
<7>....... : PRQ implemented: 1
<7>....... : IO APIC version: 0020
<7>.... register #02: 07000000
<7>....... : arbitration: 07
<7>.... register #03: 00000001
<7>....... : Boot DT : 1
<7>.... IRQ redirection table:
<7> NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
<7> 00 00F 0F 1 1 0 1 0 1 1 82
<7> 01 00F 0F 1 1 0 1 0 1 1 8A
<7> 02 000 00 1 0 0 0 0 0 0 00
<7> 03 000 00 1 0 0 0 0 0 0 00
<7> 04 000 00 1 0 0 0 0 0 0 00
<7> 05 000 00 1 0 0 0 0 0 0 00
<7> 06 000 00 1 0 0 0 0 0 0 00
<7> 07 000 00 1 0 0 0 0 0 0 00
<7> 08 000 00 1 0 0 0 0 0 0 00
<7> 09 000 00 1 0 0 0 0 0 0 00
<7> 0a 000 00 1 0 0 0 0 0 0 00
<7> 0b 000 00 1 0 0 0 0 0 0 00
<7> 0c 000 00 1 0 0 0 0 0 0 00
<7> 0d 000 00 1 0 0 0 0 0 0 00
<7> 0e 000 00 1 0 0 0 0 0 0 00
<7> 0f 000 00 1 0 0 0 0 0 0 00
<7> 10 000 00 1 0 0 0 0 0 0 00
<7> 11 000 00 1 0 0 0 0 0 0 00
<7> 12 000 00 1 0 0 0 0 0 0 00
<7> 13 000 00 1 0 0 0 0 0 0 00
<7> 14 000 00 1 0 0 0 0 0 0 00
<7> 15 000 00 1 0 0 0 0 0 0 00
<7> 16 000 00 1 0 0 0 0 0 0 00
<7> 17 000 00 1 0 0 0 0 0 0 00
<4>
<7>IO APIC #8......
<7>.... register #00: 08000000
<7>....... : physical APIC id: 08
<7>....... : Delivery Type: 0
<7>....... : LTS : 0
<7>.... register #01: 00178020
<7>....... : max redirection entries: 0017
<7>....... : PRQ implemented: 1
<7>....... : IO APIC version: 0020
<7>.... register #02: 08000000
<7>....... : arbitration: 08
<7>.... register #03: 00000001
<7>....... : Boot DT : 1
<7>.... IRQ redirection table:
<7> NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
<7> 00 00F 0F 1 1 0 1 0 1 1 92
<7> 01 00F 0F 1 1 0 1 0 1 1 9A
<7> 02 00F 0F 1 1 0 1 0 1 1 A2
<7> 03 00F 0F 1 1 0 1 0 1 1 AA
<7> 04 00F 0F 1 1 0 1 0 1 1 B2
<7> 05 00F 0F 1 1 0 1 0 1 1 BA
<7> 06 00F 0F 1 1 0 1 0 1 1 C2
<7> 07 00F 0F 1 1 0 1 0 1 1 CA
<7> 08 000 00 1 0 0 0 0 0 0 00
<7> 09 000 00 1 0 0 0 0 0 0 00
<7> 0a 000 00 1 0 0 0 0 0 0 00
<7> 0b 000 00 1 0 0 0 0 0 0 00
<7> 0c 000 00 1 0 0 0 0 0 0 00
<7> 0d 000 00 1 0 0 0 0 0 0 00
<7> 0e 000 00 1 0 0 0 0 0 0 00
<7> 0f 000 00 1 0 0 0 0 0 0 00
<7> 10 000 00 1 0 0 0 0 0 0 00
<7> 11 000 00 1 0 0 0 0 0 0 00
<7> 12 000 00 1 0 0 0 0 0 0 00
<7> 13 000 00 1 0 0 0 0 0 0 00
<7> 14 000 00 1 0 0 0 0 0 0 00
<7> 15 000 00 1 0 0 0 0 0 0 00
<7> 16 000 00 1 0 0 0 0 0 0 00
<7> 17 000 00 1 0 0 0 0 0 0 00
<7>IRQ to pin mappings:
<7>IRQ0 -> 0:2
<7>IRQ1 -> 0:1
<7>IRQ3 -> 0:3
<7>IRQ4 -> 0:4
<7>IRQ6 -> 0:6
<7>IRQ7 -> 0:7
<7>IRQ8 -> 0:8
<7>IRQ9 -> 0:9
<7>IRQ10 -> 0:10
<7>IRQ12 -> 0:12
<7>IRQ14 -> 0:14
<7>IRQ15 -> 0:15
<7>IRQ16 -> 0:16
<7>IRQ17 -> 0:17
<7>IRQ18 -> 0:18
<7>IRQ19 -> 0:19
<7>IRQ20 -> 0:20
<7>IRQ24 -> 1:0
<7>IRQ25 -> 1:1
<7>IRQ26 -> 1:2
<7>IRQ27 -> 1:3
<7>IRQ28 -> 1:4
<7>IRQ48 -> 2:0
<7>IRQ49 -> 2:1
<7>IRQ50 -> 2:2
<7>IRQ51 -> 2:3
<7>IRQ52 -> 2:4
<7>IRQ53 -> 2:5
<7>IRQ54 -> 2:6
<7>IRQ55 -> 2:7
<7>IRQ56 -> 2:8
<7>IRQ57 -> 2:9
<7>IRQ58 -> 2:10
<7>IRQ59 -> 2:11
<7>IRQ72 -> 3:0
<7>IRQ73 -> 3:1
<7>IRQ96 -> 4:0
<7>IRQ97 -> 4:1
<7>IRQ98 -> 4:2
<7>IRQ99 -> 4:3
<7>IRQ100 -> 4:4
<7>IRQ101 -> 4:5
<7>IRQ102 -> 4:6
<7>IRQ103 -> 4:7
<6>.................................... done.
<4>Using local APIC timer interrupts.
<4>calibrating APIC timer ...
<4>..... CPU clock speed is 2791.7565 MHz.
<4>..... host bus clock speed is 99.7054 MHz.
<4>cpu: 0, clocks: 997054, slice: 199410
<4>CPU0<T0:997040,T1:797616,D:14,S:199410,C:997054>
<4>cpu: 1, clocks: 997054, slice: 199410
<4>cpu: 2, clocks: 997054, slice: 199410
<4>cpu: 3, clocks: 997054, slice: 199410
<4>CPU1<T0:997040,T1:598208,D:12,S:199410,C:997054>
<4>CPU2<T0:997040,T1:398800,D:10,S:199410,C:997054>
<4>CPU3<T0:997040,T1:199392,D:8,S:199410,C:997054>
<4>checking TSC synchronization across CPUs: passed.
<4>Waiting on wait_init_idle (map = 0xe)
<4>All processors have done init_idle
<6>PCI: PCI BIOS revision 2.10 entry at 0xfc6ce, last bus=11
<6>PCI: Using configuration type 1
<6>PCI: Probing PCI hardware
<4>PCI: Probing PCI hardware (bus 00)
<6>PCI: Ignoring BAR0-3 of IDE controller 00:1f.1
<4>Transparent bridge - PCI device 8086:244e
<6>PCI: Using IRQ router PIIX/ICH [8086/2480] at 00:1f.0
<6>PCI->APIC IRQ transform: (B0,I29,P0) -> 16
<6>PCI->APIC IRQ transform: (B0,I31,P0) -> 16
<6>PCI->APIC IRQ transform: (B3,I1,P0) -> 28
<6>PCI->APIC IRQ transform: (B9,I13,P0) -> 72
<6>PCI->APIC IRQ transform: (B9,I13,P1) -> 73
<6>PCI->APIC IRQ transform: (B11,I0,P0) -> 16
<6>Linux NET4.0 for Linux 2.4
<6>Based upon Swansea University Computer Society NET3.039
<4>Initializing RT netlink socket
<6>apm: BIOS not found.
<4>Starting kswapd
<4>allocated 32 pages and 32 bhs reserved for the highmem bounces
<6>Detected PS/2 Mouse Port.
<6>Real Time Clock Driver v1.10f
<6>Intel(R) PRO/1000 Network Driver - version 5.2.20-k1
<6>Copyright (c) 1999-2003 Intel Corporation.
<6>eth0: Intel(R) PRO/1000 Network Connection
<4>3c59x: Donald Becker and others. www.scyld.com/network/vortex.html
<6>See Documentation/networking/vortex.txt
<6>0b:00.0: 3Com PCI 3c905C Tornado at 0xcc80. Vers LK1.1.18-ac
<4> 00:04:75:c9:70:0c, IRQ 16
<6> product code 564c rev 00.6 date 09-28-02
<7> Internal config register is 1800000, transceivers 0xa.
<6> 8K byte-wide RAM 5:3 Rx:Tx split, autoselect/Autonegotiate interface.
<6> MII transceiver found at address 24, status 7809.
<6> Enabling bus-master transmits and whole-frame receives.
<6>0b:00.0: scatter/gather enabled. h/w checksums enabled
<6>Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
<6>ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
<6>ICH3: IDE controller at PCI slot 00:1f.1
<4>PCI: Enabling device 00:1f.1 (0005 -> 0007)
<6>ICH3: chipset revision 2
<6>ICH3: not 100% native mode: will probe irqs later
<6> ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda:DMA, hdb:pio
<6> ide1: BM-DMA at 0xfc08-0xfc0f, BIOS settings: hdc:pio, hdd:pio
<4>hda: SAMSUNG CD-ROM SN-124, ATAPI CD/DVD-ROM drive
<4>ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
<6>SCSI subsystem driver Revision: 1.00
<6>Fusion MPT base driver 2.05.11.03
<6>Copyright (c) 1999-2003 LSI Logic Corporation
<6>mptbase: Initiating ioc0 bringup
<6>ioc0: 53C1030: Capabilities={Initiator}
<6>mptbase: Initiating ioc1 bringup
<6>ioc1: 53C1030: Capabilities={Initiator}
<6>mptbase: 2 MPT adapters found, 2 installed.
<6>Fusion MPT SCSI Host driver 2.05.11.03
<6>scsi0 : ioc0: LSI53C1030, FwRev=01000c00h, Ports=1, MaxQ=255, IRQ=72
<6>scsi1 : ioc1: LSI53C1030, FwRev=01000c00h, Ports=1, MaxQ=255, IRQ=73
<4>blk: queue f7bb0a18, I/O limit 4294967295Mb (mask 0xffffffffffffffff)
<4> Vendor: FUJITSU Model: MAP3147NC Rev: 5605
<4> Type: Direct-Access ANSI SCSI revision: 03
<4>blk: queue f7bb0818, I/O limit 4294967295Mb (mask 0xffffffffffffffff)
<4> Vendor: FUJITSU Model: MAP3147NC Rev: 5605
<4> Type: Direct-Access ANSI SCSI revision: 03
<4>blk: queue f7bb0618, I/O limit 4294967295Mb (mask 0xffffffffffffffff)
<4> Vendor: PE/PV Model: 1x2 SCSI BP Rev: 1.1
<4> Type: Processor ANSI SCSI revision: 02
<4>blk: queue f7affc18, I/O limit 4294967295Mb (mask 0xffffffffffffffff)
<4> Vendor: SEAGATE Model: ST3146807LC Rev: DS04
<4> Type: Direct-Access ANSI SCSI revision: 03
<4>blk: queue f7adca18, I/O limit 4294967295Mb (mask 0xffffffffffffffff)
<4> Vendor: SEAGATE Model: ST3146807LC Rev: DS04
<4> Type: Direct-Access ANSI SCSI revision: 03
<4>blk: queue f7adc818, I/O limit 4294967295Mb (mask 0xffffffffffffffff)
<4> Vendor: SEAGATE Model: ST3146807LC Rev: DS04
<4> Type: Direct-Access ANSI SCSI revision: 03
<4>blk: queue f7adc618, I/O limit 4294967295Mb (mask 0xffffffffffffffff)
<4> Vendor: SEAGATE Model: ST3146807LC Rev: DS04
<4> Type: Direct-Access ANSI SCSI revision: 03
<4>blk: queue f7adc418, I/O limit 4294967295Mb (mask 0xffffffffffffffff)
<4> Vendor: SEAGATE Model: ST3146807LC Rev: DS04
<4> Type: Direct-Access ANSI SCSI revision: 03
<4>blk: queue f7adc218, I/O limit 4294967295Mb (mask 0xffffffffffffffff)
<4> Vendor: SEAGATE Model: ST3146807LC Rev: DS04
<4> Type: Direct-Access ANSI SCSI revision: 03
<4>blk: queue f7adc018, I/O limit 4294967295Mb (mask 0xffffffffffffffff)
<4> Vendor: PE/PV Model: 1x6 SCSI BP Rev: 1.1
<4> Type: Processor ANSI SCSI revision: 02
<4>blk: queue f7a0ee18, I/O limit 4294967295Mb (mask 0xffffffffffffffff)
<4>Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
<4>Attached scsi disk sdb at scsi0, channel 0, id 1, lun 0
<4>Attached scsi disk sdc at scsi1, channel 0, id 0, lun 0
<4>Attached scsi disk sdd at scsi1, channel 0, id 1, lun 0
<4>Attached scsi disk sde at scsi1, channel 0, id 2, lun 0
<4>Attached scsi disk sdf at scsi1, channel 0, id 3, lun 0
<4>Attached scsi disk sdg at scsi1, channel 0, id 4, lun 0
<4>Attached scsi disk sdh at scsi1, channel 0, id 5, lun 0
<4>SCSI device sda: 286749480 512-byte hdwr sectors (146816 MB)
<6>Partition check:
<6> sda: sda1
<4>SCSI device sdb: 286749480 512-byte hdwr sectors (146816 MB)
<6> sdb: sdb1
<4>SCSI device sdc: 286749480 512-byte hdwr sectors (146816 MB)
<6> sdc: sdc1
<4>SCSI device sdd: 286749480 512-byte hdwr sectors (146816 MB)
<6> sdd: sdd1
<4>SCSI device sde: 286749480 512-byte hdwr sectors (146816 MB)
<6> sde: sde1
<4>SCSI device sdf: 286749480 512-byte hdwr sectors (146816 MB)
<6> sdf: sdf1
<4>SCSI device sdg: 286749480 512-byte hdwr sectors (146816 MB)
<6> sdg: sdg1
<4>SCSI device sdh: 286749480 512-byte hdwr sectors (146816 MB)
<6> sdh: sdh1
<6>md: linear personality registered as nr 1
<6>md: raid0 personality registered as nr 2
<6>md: raid1 personality registered as nr 3
<6>md: raid5 personality registered as nr 4
<6>raid5: measuring checksumming speed
<4> 8regs : 3225.200 MB/sec
<4> 32regs : 2412.400 MB/sec
<4> pIII_sse : 3657.200 MB/sec
<4> pII_mmx : 3299.600 MB/sec
<4> p5_mmx : 3363.200 MB/sec
<4>raid5: using function: pIII_sse (3657.200 MB/sec)
<6>md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
<6>md: Autodetecting RAID arrays.
<6> [events: 00000027]
<6> [events: 00000027]
<6> [events: 00000017]
<6> [events: 00000017]
<6> [events: 00000017]
<6> [events: 00000017]
<6> [events: 00000017]
<6> [events: 00000017]
<6>md: autorun ...
<6>md: considering sdh1 ...
<6>md: adding sdh1 ...
<6>md: adding sdg1 ...
<6>md: adding sdf1 ...
<6>md: adding sde1 ...
<6>md: adding sdd1 ...
<6>md: adding sdc1 ...
<6>md: created md1
<6>md: bind<sdc1,1>
<6>md: bind<sdd1,2>
<6>md: bind<sde1,3>
<6>md: bind<sdf1,4>
<6>md: bind<sdg1,5>
<6>md: bind<sdh1,6>
<6>md: running: <sdh1><sdg1><sdf1><sde1><sdd1><sdc1>
<6>md: sdh1's event counter: 00000017
<6>md: sdg1's event counter: 00000017
<6>md: sdf1's event counter: 00000017
<6>md: sde1's event counter: 00000017
<6>md: sdd1's event counter: 00000017
<6>md: sdc1's event counter: 00000017
<6>md1: max total readahead window set to 1280k
<6>md1: 5 data-disks, max readahead per data-disk: 256k
<6>raid5: device sdh1 operational as raid disk 5
<6>raid5: device sdg1 operational as raid disk 4
<6>raid5: device sdf1 operational as raid disk 3
<6>raid5: device sde1 operational as raid disk 2
<6>raid5: device sdd1 operational as raid disk 1
<6>raid5: device sdc1 operational as raid disk 0
<6>raid5: allocated 6429kB for md1
<4>raid5: raid level 5 set md1 active with 6 out of 6 devices, algorithm 0
<4>RAID5 conf printout:
<4> --- rd:6 wd:6 fd:0
<4> disk 0, s:0, o:1, n:0 rd:0 us:1 dev:sdc1
<4> disk 1, s:0, o:1, n:1 rd:1 us:1 dev:sdd1
<4> disk 2, s:0, o:1, n:2 rd:2 us:1 dev:sde1
<4> disk 3, s:0, o:1, n:3 rd:3 us:1 dev:sdf1
<4> disk 4, s:0, o:1, n:4 rd:4 us:1 dev:sdg1
<4> disk 5, s:0, o:1, n:5 rd:5 us:1 dev:sdh1
<4>RAID5 conf printout:
<4> --- rd:6 wd:6 fd:0
<4> disk 0, s:0, o:1, n:0 rd:0 us:1 dev:sdc1
<4> disk 1, s:0, o:1, n:1 rd:1 us:1 dev:sdd1
<4> disk 2, s:0, o:1, n:2 rd:2 us:1 dev:sde1
<4> disk 3, s:0, o:1, n:3 rd:3 us:1 dev:sdf1
<4> disk 4, s:0, o:1, n:4 rd:4 us:1 dev:sdg1
<4> disk 5, s:0, o:1, n:5 rd:5 us:1 dev:sdh1
<6>md: updating md1 RAID superblock on device
<6>md: sdh1 [events: 00000018]<6>(write) sdh1's sb offset: 143371968
<6>md: sdg1 [events: 00000018]<6>(write) sdg1's sb offset: 143371968
<6>md: sdf1 [events: 00000018]<6>(write) sdf1's sb offset: 143371968
<6>md: sde1 [events: 00000018]<6>(write) sde1's sb offset: 143371968
<6>md: sdd1 [events: 00000018]<6>(write) sdd1's sb offset: 143371968
<6>md: sdc1 [events: 00000018]<6>(write) sdc1's sb offset: 143371968
<6>md: considering sdb1 ...
<6>md: adding sdb1 ...
<6>md: adding sda1 ...
<6>md: created md0
<6>md: bind<sda1,1>
<6>md: bind<sdb1,2>
<6>md: running: <sdb1><sda1>
<6>md: sdb1's event counter: 00000027
<6>md: sda1's event counter: 00000027
<6>md: RAID level 1 does not need chunksize! Continuing anyway.
<6>md0: max total readahead window set to 124k
<6>md0: 1 data-disks, max readahead per data-disk: 124k
<6>raid1: device sdb1 operational as mirror 1
<6>raid1: device sda1 operational as mirror 0
<6>raid1: raid set md0 active with 2 out of 2 mirrors
<6>md: updating md0 RAID superblock on device
<6>md: sdb1 [events: 00000028]<6>(write) sdb1's sb offset: 143371968
<6>md: sda1 [events: 00000028]<6>(write) sda1's sb offset: 143371968
<4>SCSI Error: (0:0:0) Status=02h (CHECK CONDITION)
<4> Key=6h (UNIT ATTENTION); FRU=00h
<4> ASC/ASCQ=29h/02h "SCSI BUS RESET OCCURRED"
<4> CDB: 2A 00 11 17 5D BF 00 00 08 00
<4>
<6>md: ... autorun DONE.
<6>NET4: Linux TCP/IP 1.0 for NET4.0
<6>IP Protocols: ICMP, UDP, TCP
<6>IP: routing cache hash table of 16384 buckets, 128Kbytes
<6>TCP: Hash tables configured (established 262144 bind 65536)
<6>NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
<4>VFS: Mounted root (ext2 filesystem) readonly.
<6>Freeing unused kernel memory: 112k freed
<4>raid5: switching cache buffer size, 4096 --> 1024
<4>raid5: switching cache buffer size, 1024 --> 4096
<6>e1000: eth0 NIC Link is Up 100 Mbps Full Duplex
next reply other threads:[~2004-03-11 17:41 UTC|newest]
Thread overview: 4+ messages / expand[flat|nested] mbox.gz Atom feed top
2004-03-11 17:30 Hubert Tonneau [this message]
-- strict thread matches above, loose matches on Subject: below --
2004-03-11 17:21 Linux 2.6 no boot report Hubert Tonneau
2004-03-11 16:32 Hubert Tonneau
2004-03-11 16:54 ` Matt Domsch
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=043MZAY12@server5.heliogroup.fr \
--to=hubert.tonneau@fullpliant.org \
--cc=linux-kernel@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.