From mboxrd@z Thu Jan  1 00:00:00 1970
From: Alexander von Gluck IV <kallisti5@unixzen.com>
Date: Mon, 23 Sep 2019 13:06:35 +0000
Subject: [U-Boot]
 =?utf-8?q?rk3288_=28Tinkerboard=29_not_booting=E3=80=90?=
 =?utf-8?b?6K+35rOo5oSP77yM6YKu5Lu255SxdS1ib290LWJvdW5jZXNAbGlzdHMuZGVu?=
 =?utf-8?b?eC5kZeS7o+WPkeOAkQ==?=
In-Reply-To: <20190923053422.GA37062@largo.jsg.id.au>
References: <20190923053422.GA37062@largo.jsg.id.au>
 <8f3b3fc8-0ddf-ffbb-d18e-29092541db24@rock-chips.com>
 <CAOf5uwmKXwjXczLs0y+m9oyUXSSZnnenuNvzDk4j57Apg5svjA@mail.gmail.com>
 <266c5f804b792ce038315ebe49ad667d@unixzen.com>
 <718d9a0495c3d940e4f00038cbdd495e@unixzen.com>
 <5f3823eccbce1b4338ed6aef4d1d6a7f@unixzen.com>
Message-ID: <0f0bc15accbea5a9ee0f027e7edf95b3@unixzen.com>
List-Id: <u-boot.lists.denx.de>
MIME-Version: 1.0
Content-Type: text/plain; charset="us-ascii"
Content-Transfer-Encoding: 7bit
To: u-boot@lists.denx.de

Ok, looking for differences now..

* Older Tinker Board?  (I'm not using the Tinker Board S)
* Same steps?
* Same config?  tinker-rk3288_defconfig?
* Uart 115200?
* Any HDMI Video output?
* GCC version?

September 23, 2019 12:34 AM, "Jonathan Gray" <jsg@jsg.id.au> wrote:

> On Mon, Sep 23, 2019 at 01:17:40AM +0000, Alexander von Gluck IV wrote:
> 
>> Hello!
>> 
>> There is no uart output and no video with u-boot master.
>> The board works as expected booting the Asus Armbian image on an SD.
>> 
>> At this point i'd be happy to get some u-boot uart output :-)
>> 
>> -- Alex
> 
> uart output works here with the latest master
> (780a17e814503f71d1b51d578b32bc9c89933183)
> 
> U-Boot TPL 2019.10-rc3-00401-ge23a6e5c43 (Sep 23 2019 - 15:13:20)
> Trying to boot from BOOTROM
> Returning to boot ROM...
> 
> U-Boot SPL 2019.10-rc3-00401-ge23a6e5c43 (Sep 23 2019 - 15:13:20 +1000)
> Trying to boot from MMC1
> 
> U-Boot 2019.10-rc3-00401-ge23a6e5c43 (Sep 23 2019 - 15:13:20 +1000)
> 
> Model: Tinker-RK3288
> DRAM: 2 GiB
> MMC: dwmmc at ff0c0000: 1
> Loading Environment from MMC... *** Warning - bad CRC, using default environment
> 
> In: serial
> Out: serial
> Err: serial
> Model: Tinker-RK3288
> rockchip_dnl_key_pressed: adc_channel_single_shot fail!
> Net: eth0: ethernet at ff290000
> Hit any key to stop autoboot: 0
> switch to partitions #0, OK
> mmc1 is current device
> Scanning mmc 1:1...
> Found EFI removable media binary efi/boot/bootarm.efi
> libfdt fdt_check_header(): FDT_ERR_BADMAGIC
> Scanning disk dwmmc at ff0c0000.blk...
> Found 3 disks
> BootOrder not defined
> EFI boot manager: Cannot load any image
> 88176 bytes read in 9 ms (9.3 MiB/s)
> libfdt fdt_check_header(): FDT_ERR_BADMAGIC
>>> OpenBSD/armv7 BOOTARM 1.6
> 
> boot>