From: Beezly <beezly@beezly.org.uk>
To: davem@redhat.com, linux-kernel@vger.kernel.org
Subject: Re: sungem card fails to find it's mac address
Date: 04 Mar 2002 22:00:42 +0000 [thread overview]
Message-ID: <1015279242.1961.15.camel@monkey> (raw)
In-Reply-To: <1015277575.1961.12.camel@monkey>
In-Reply-To: <1015277575.1961.12.camel@monkey>
[-- Attachment #1: Type: text/plain, Size: 12197 bytes --]
I don the dunce's hat.
I forgot to say what kernel I'm running;
monkey:/# uname -a
Linux monkey 2.4.19pre1 #1 Mon Feb 25 21:48:03 GMT 2002 i686 unknown
On Mon, 2002-03-04 at 21:32, Beezly wrote:
> Hi all,
>
> I've just been trying out a Sun Gigabit Ethernet card on my PC. As the
> sungem module loads it prints out:
>
> Mar 4 20:40:10 monkey kernel: sungem.c:v0.96 11/17/01 David S. Miller
> (davem@redhat.com)
> Mar 4 20:40:10 monkey kernel: PCI: Enabling device 00:0a.0 (0014 ->
> 0016)
> Mar 4 20:40:10 monkey kernel: PCI: Found IRQ 5 for device 00:0a.0
> Mar 4 20:40:10 monkey kernel: PCI: Sharing IRQ 5 with 00:0b.1
> Mar 4 20:40:10 monkey kernel: eth0: Sun GEM (PCI) 10/100/1000BaseT
> Ethernet 00:00:00:00:00:00
>
> and the card fails to establish a link with the switch (an extreme
> networks summit 48). If I then "encourage" the card to have a mac
> address (I used one stolen from a 3COM 3c905B!) the link is established
> straight away;
>
> (immediately after doing "ifconfig eth0 hw ether 00:10:5A:41:E6:14")
>
> Mar 4 21:06:27 monkey kernel: eth0: Link is up at 1000 Mbps,
> full-duplex.
> Mar 4 21:06:27 monkey kernel: eth0: PCS AutoNEG complete.
> Mar 4 21:06:27 monkey kernel: eth0: PCS link is now up.
> Mar 4 21:06:28 monkey kernel: eth0: Link is up at 1000 Mbps,
> full-duplex.
>
> After doing this, the card functions as expected, except I get a message
> to syslog around once every second saying;
>
> Mar 4 21:18:25 monkey kernel: eth0: Link is up at 1000 Mbps,
> full-duplex.
>
> I'm guess this could be the switch forcing a renegotiation every second
> and I may be able to turn it off - on the other hand, it could be useful
> information for someone;
>
> If any more info is needed please contact me ;)
>
> Also attached is the output of lspci -v
>
> monkey:/var/log# lspci -vv
> 00:00.0 Host bridge: VIA Technologies, Inc. VT8363/8365 [KT133/KM133]
> (rev 02)
> Subsystem: Asustek Computer, Inc.: Unknown device 8033
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B-
> Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort+ >SERR- <PERR-
> Latency: 8
> Region 0: Memory at e6000000 (32-bit, prefetchable) [size=32M]
> Capabilities: [a0] AGP version 2.0
> Status: RQ=31 SBA+ 64bit- FW+ Rate=x1,x2
> Command: RQ=0 SBA- AGP+ 64bit- FW+ Rate=<none>
> Capabilities: [c0] Power Management version 2
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
> PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
> 00:01.0 PCI bridge: VIA Technologies, Inc. VT8363/8365 [KT133/KM133 AGP]
> (prog-if 00 [Normal decode])
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B-
> Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort+ >SERR- <PERR-
> Latency: 0
> Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
> Memory behind bridge: d5000000-d65fffff
> Prefetchable memory behind bridge: d7f00000-e5ffffff
> BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B-
> Capabilities: [80] Power Management version 2
> Flags: PMEClk- DSI+ D1+ D2- AuxCurrent=0mA
> PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
> 00:04.0 ISA bridge: VIA Technologies, Inc. VT82C686 [Apollo Super South]
> (rev 22)
> Subsystem: Asustek Computer, Inc.: Unknown device 8033
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping+ SERR- FastB2B-
> Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Latency: 0
>
> 00:04.1 IDE interface: VIA Technologies, Inc. Bus Master IDE (rev 10)
> (prog-if 8a [Master SecP PriP])
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B-
> Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Latency: 32
> Region 4: I/O ports at d800 [size=16]
> Capabilities: [c0] Power Management version 2
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
> PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
> 00:04.2 USB Controller: VIA Technologies, Inc. UHCI USB (rev 10)
> (prog-if 00 [UHCI])
> Subsystem: Unknown device 0925:1234
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
> Stepping- SERR- FastB2B-
> Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Latency: 32, cache line size 08
> Interrupt: pin D routed to IRQ 9
> Region 4: I/O ports at d400 [size=32]
> Capabilities: [80] Power Management version 2
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
> PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
> 00:04.3 USB Controller: VIA Technologies, Inc. UHCI USB (rev 10)
> (prog-if 00 [UHCI])
> Subsystem: Unknown device 0925:1234
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
> Stepping- SERR- FastB2B-
> Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Latency: 32, cache line size 08
> Interrupt: pin D routed to IRQ 9
> Region 4: I/O ports at d000 [size=32]
> Capabilities: [80] Power Management version 2
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
> PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
> 00:04.4 Bridge: VIA Technologies, Inc. VT82C686 [Apollo Super ACPI] (rev
> 30)
> Subsystem: Asustek Computer, Inc.: Unknown device 8033
> Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B-
> Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Interrupt: pin ? routed to IRQ 9
> Capabilities: [68] Power Management version 2
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
> PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
> 00:09.0 Multimedia video controller: Brooktree Corporation Bt878 (rev
> 02)
> Subsystem: Hauppauge computer works Inc. WinTV/GO
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B-
> Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Latency: 32 (4000ns min, 10000ns max)
> Interrupt: pin A routed to IRQ 9
> Region 0: Memory at d7000000 (32-bit, prefetchable) [size=4K]
>
> 00:09.1 Multimedia controller: Brooktree Corporation Bt878 (rev 02)
> Subsystem: Hauppauge computer works Inc. WinTV/GO
> Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B-
> Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Latency: 32 (1000ns min, 63750ns max)
> Interrupt: pin A routed to IRQ 9
> Region 0: Memory at d6800000 (32-bit, prefetchable) [disabled]
> [size=4K]
>
> 00:0a.0 Ethernet controller: Sun Microsystems Computer Corp. GEM (rev
> 01)
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
> Stepping- SERR- FastB2B-
> Status: Cap- 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=slow >TAbort- <TAbort-
> <MAbort- >SERR- <PERR-
> Latency: 32 (16000ns min, 16000ns max), cache line size 08
> Interrupt: pin A routed to IRQ 5
> Region 0: Memory at d4800000 (32-bit, non-prefetchable) [size=2M]
> Expansion ROM at <unassigned> [disabled] [size=1M]
>
> 00:0b.0 SCSI storage controller: LSI Logic / Symbios Logic (formerly
> NCR) 53c875 (rev 14)
> Subsystem: LSI Logic / Symbios Logic (formerly NCR): Unknown device
> 1000
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr+
> Stepping- SERR- FastB2B-
> Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Latency: 72 (4250ns min, 16000ns max), cache line size 08
> Interrupt: pin A routed to IRQ 10
> Region 0: I/O ports at a400 [size=256]
> Region 1: Memory at d4000000 (32-bit, non-prefetchable) [size=256]
> Region 2: Memory at d3800000 (32-bit, non-prefetchable) [size=4K]
> Expansion ROM at <unassigned> [disabled] [size=64K]
>
> 00:0b.1 SCSI storage controller: LSI Logic / Symbios Logic (formerly
> NCR) 53c875 (rev 14)
> Subsystem: LSI Logic / Symbios Logic (formerly NCR): Unknown device
> 1000
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr+
> Stepping- SERR- FastB2B-
> Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Latency: 72 (4250ns min, 16000ns max), cache line size 08
> Interrupt: pin B routed to IRQ 5
> Region 0: I/O ports at a000 [size=256]
> Region 1: Memory at d3000000 (32-bit, non-prefetchable) [size=256]
> Region 2: Memory at d2800000 (32-bit, non-prefetchable) [size=4K]
> Expansion ROM at <unassigned> [disabled] [size=64K]
>
> 00:0c.0 Multimedia audio controller: Creative Labs SB Live! EMU10k1 (rev
> 05)
> Subsystem: Creative Labs CT4850 SBLive! Value
> Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B-
> Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Latency: 32 (500ns min, 5000ns max)
> Interrupt: pin A routed to IRQ 11
> Region 0: I/O ports at 9800 [size=32]
> Capabilities: [dc] Power Management version 1
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
> PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
> 00:0c.1 Input device controller: Creative Labs SB Live! (rev 05)
> Subsystem: Creative Labs Gameport Joystick
> Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B-
> Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Latency: 32
> Region 0: I/O ports at 9400 [disabled] [size=8]
> Capabilities: [dc] Power Management version 1
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
> PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
> 00:11.0 Unknown mass storage controller: Promise Technology, Inc. 20265
> (rev 02)
> Subsystem: Promise Technology, Inc.: Unknown device 4d33
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B-
> Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Latency: 32
> Interrupt: pin A routed to IRQ 10
> Region 0: I/O ports at 9000 [size=8]
> Region 1: I/O ports at 8800 [size=4]
> Region 2: I/O ports at 8400 [size=8]
> Region 3: I/O ports at 8000 [size=4]
> Region 4: I/O ports at 7800 [size=64]
> Region 5: Memory at d2000000 (32-bit, non-prefetchable) [size=128K]
> Expansion ROM at <unassigned> [disabled] [size=64K]
> Capabilities: [58] Power Management version 1
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
> PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
> 01:00.0 VGA compatible controller: nVidia Corporation NV11 (GeForce2 MX)
> (rev a1) (prog-if 00 [VGA])
> Subsystem: CardExpert Technology: Unknown device 0065
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B-
> Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Latency: 248 (1250ns min, 250ns max)
> Interrupt: pin A routed to IRQ 11
> Region 0: Memory at d5000000 (32-bit, non-prefetchable) [size=16M]
> Region 1: Memory at d8000000 (32-bit, prefetchable) [size=128M]
> Expansion ROM at d7ff0000 [disabled] [size=64K]
> Capabilities: [60] Power Management version 2
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
> PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
> Capabilities: [44] AGP version 2.0
> Status: RQ=31 SBA- 64bit- FW+ Rate=x1,x2
> Command: RQ=31 SBA- AGP+ 64bit- FW+ Rate=<none>
>
>
[-- Attachment #2: This is a digitally signed message part --]
[-- Type: application/pgp-signature, Size: 232 bytes --]
next prev parent reply other threads:[~2002-03-04 22:01 UTC|newest]
Thread overview: 3+ messages / expand[flat|nested] mbox.gz Atom feed top
2002-03-04 21:32 sungem card fails to find it's mac address Beezly
2002-03-04 22:00 ` Beezly [this message]
2002-03-04 23:28 ` David S. Miller
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1015279242.1961.15.camel@monkey \
--to=beezly@beezly.org.uk \
--cc=davem@redhat.com \
--cc=linux-kernel@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.