From: Jim Halfpenny <jimvin@lineone.net>
To: linux-kernel@vger.kernel.org, linux-ide@vger.kernel.org
Subject: UDMA causes IDE corruption on Shuttle AK32L mobo (VIA KT266A), kernel 2.4.1[89]
Date: 29 Nov 2002 20:15:01 +0000 [thread overview]
Message-ID: <1038600903.2074.2.camel@fox> (raw)
Hi,
I'm experiencing corrupted writes to IDE disks using a Shuttle AK32
V2.1 motherboard, Athlon XP1800+, 256Mb DDR RAM when DMA is enabled.
Disabling DMA using `hdparm -d0 /dev/hda` fixes this. I have tried
two different hard disks, so I don't think that it is a fault with
the drive itself.
I have seen the behaviour using the stock 2.4.18 kernel from Mandrake
8.2. and the 2.4.19 kernel from Mandrake 9.0:
Linux version 2.4.19-16mdk (quintela@bi.mandrakesoft.com) (gcc version
3.2 (Mandrake Linux 9.0 3.2-1mdk)) #1 Fri Sep 20 18:15:05 CEST 2002
There are no log entries in /var/log/messages or /var/log/syslog when
these faulty writes take place to indicate that there are any problems
but copying a large file and checking it's md5sum shows it to be
damaged.
Below is the output of various commands / logs which may be relevant.
Regards,
Jim Halfpenny
########################
Startup log messages (/var/log/messages):
Nov 24 12:24:47 fox kernel: ide: Assuming 33MHz system bus speed for PIO
modes; override with idebus=xx
Nov 24 12:24:47 fox kernel: VP_IDE: IDE controller on PCI bus 00 dev 89
Nov 24 12:24:47 fox kernel: PCI: No IRQ known for interrupt pin A of
device 00:11.1. Please try using pci=biosirq.
Nov 24 12:24:47 fox kernel: VP_IDE: chipset revision 6
Nov 24 12:24:47 fox kernel: VP_IDE: not 100%% native mode: will probe
irqs later
Nov 24 12:24:47 fox kernel: VP_IDE: VIA vt8233 (rev 00) IDE UDMA100
controller on pci00:11.1
Nov 24 12:24:47 fox kernel: ide0: BM-DMA at 0xe000-0xe007, BIOS
settings: hda:DMA, hdb:pio
Nov 24 12:24:47 fox kernel: ide1: BM-DMA at 0xe008-0xe00f, BIOS
settings: hdc:DMA, hdd:DMA
Nov 24 12:24:47 fox kernel: hda: FUJITSU MPD3130AT, ATA DISK drive
Nov 24 12:24:47 fox kernel: hdc: YAMAHA CRW8824E, ATAPI CD/DVD-ROM drive
Nov 24 12:24:47 fox kernel: hdd: MATSHITADVD-ROM SR-8585, ATAPI
CD/DVD-ROM drive
Nov 24 12:24:47 fox kernel: ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Nov 24 12:24:47 fox kernel: ide1 at 0x170-0x177,0x376 on irq 15
Nov 24 12:24:47 fox kernel: hda: 25431840 sectors (13021 MB) w/512KiB
Cache, CHS=2909/141/62, UDMA(66)
Nov 24 12:24:47 fox kernel: Partition check:
Nov 24 12:24:47 fox kernel: /dev/ide/host0/bus0/target0/lun0:<6> [PTBL]
[1583/255/63] p1 p2
########################
$ cat /proc/cpuinfo
processor : 0
vendor_id : AuthenticAMD
cpu family : 6
model : 6
model name : AMD Athlon(tm) XP 1800+
stepping : 2
cpu MHz : 1535.230
cache size : 256 KB
fdiv_bug : no
hlt_bug : no
f00f_bug : no
coma_bug : no
fpu : yes
fpu_exception : yes
cpuid level : 1
wp : yes
flags : fpu vme de tsc msr pae mce cx8 apic sep mtrr pge mca
cmov pat pse36 mmx fxsr sse syscall mmxext 3dnowext 3dnow
bogomips : 3060.53
########################
$ cat /proc/ide/via (With DMA disabled for /dev/hda)
----------VIA BusMastering IDE Configuration----------------
Driver Version: 3.34
South Bridge: VIA vt8233
Revision: ISA 0x0 IDE 0x6
Highest DMA rate: UDMA100
BM-DMA base: 0xe000
PCI clock: 33.3MHz
Master Read Cycle IRDY: 0ws
Master Write Cycle IRDY: 0ws
BM IDE Status Register Read Retry: yes
Max DRDY Pulse Width: No limit
-----------------------Primary IDE-------Secondary IDE------
Read DMA FIFO flush: yes yes
End Sector FIFO flush: no no
Prefetch Buffer: yes yes
Post Write Buffer: yes yes
Enabled: yes yes
Simplex only: no no
Cable Type: 80w 40w
-------------------drive0----drive1----drive2----drive3-----
Transfer Mode: PIO PIO PIO PIO
Address Setup: 30ns 120ns 30ns 30ns
Cmd Active: 90ns 90ns 90ns 90ns
Cmd Recovery: 30ns 30ns 30ns 30ns
Data Active: 90ns 330ns 90ns 90ns
Data Recovery: 30ns 270ns 30ns 30ns
Cycle Time: 120ns 600ns 120ns 120ns
Transfer Rate: 16.6MB/s 3.3MB/s 16.6MB/s 16.6MB/s
########################
$ cat /proc/modules
floppy 49340 0 (autoclean)
snd-seq-midi 3680 0 (autoclean) (unused)
snd-emu10k1-synth 4220 0 (autoclean) (unused)
snd-emux-synth 25532 0 (autoclean) [snd-emu10k1-synth]
snd-seq-midi-emul 4880 0 (autoclean) [snd-emux-synth]
snd-seq-virmidi 2888 0 (autoclean) [snd-emux-synth]
snd-seq-oss 26176 0 (unused)
snd-seq-midi-event 3208 0 [snd-seq-midi snd-seq-virmidi
snd-seq-oss]
snd-seq 33264 2 [snd-seq-midi snd-emux-synth
snd-seq-midi-emul snd-seq-virmidi snd-seq-oss snd-seq-midi-event]
snd-pcm-oss 36932 0
snd-mixer-oss 9016 1 [snd-pcm-oss]
snd-emu10k1 56592 1 [snd-emu10k1-synth]
snd-pcm 55808 0 [snd-pcm-oss snd-emu10k1]
snd-timer 9964 0 [snd-seq snd-pcm]
snd-util-mem 1280 0 [snd-emux-synth snd-emu10k1]
snd-rawmidi 12864 0 [snd-seq-midi snd-seq-virmidi
snd-emu10k1]
snd-seq-device 3836 0 [snd-seq-midi snd-emu10k1-synth
snd-emux-synth snd-seq-oss snd-seq snd-emu10k1 snd-rawmidi]
snd-ac97-codec 25508 0 [snd-emu10k1]
snd-hwdep 3840 0 [snd-emu10k1]
snd 24804 0 [snd-seq-midi snd-emux-synth
snd-seq-virmidi snd-seq-oss snd-seq-midi-event snd-seq snd-pcm-oss
snd-mixer-oss snd-emu10k1 snd-pcm snd-timer snd-util-mem snd-rawmidi
snd-seq-device snd-ac97-codec snd-hwdep]
soundcore 3780 0 [snd]
ppp_async 7456 0 (unused)
ppp_generic 20064 0 [ppp_async]
slhc 5072 0 [ppp_generic]
af_packet 13000 0 (autoclean)
8139too 14472 1 (autoclean)
mii 1152 0 (autoclean) [8139too]
supermount 14340 1 (autoclean)
isofs 25652 0 (autoclean)
inflate_fs 17892 0 (autoclean) [isofs]
sr_mod 15096 0 (autoclean)
ide-cd 28712 0
cdrom 26848 0 [sr_mod ide-cd]
ide-scsi 8212 0
usb-uhci 21676 0 (unused)
usbcore 58304 1 [usb-uhci]
rtc 6560 0 (autoclean)
reiserfs 169776 5
sd_mod 11612 8
eata 20472 4
scsi_mod 91140 4 [sr_mod ide-scsi sd_mod eata]
########################
$ cat /proc/ioports
0000-001f : dma1
0020-003f : pic1
0040-005f : timer
0060-006f : keyboard
0070-007f : rtc
0080-008f : dma page reg
00a0-00bf : pic2
00c0-00df : dma2
00f0-00ff : fpu
0170-0177 : ide1
01f0-01f7 : ide0
02f8-02ff : serial(auto)
0376-0376 : ide1
03c0-03df : vesafb
03f6-03f6 : ide0
03f8-03ff : serial(auto)
0cf8-0cff : PCI conf1
d000-d01f : Distributed Processing Technology SmartCache/Raid I-IV
Controller
d010-d018 : EATA
d400-d4ff : Realtek Semiconductor Co., Ltd. RTL-8139/8139C
d400-d4ff : 8139too
d800-d81f : Creative Labs SB Live! EMU10k1
d800-d81f : EMU10K1
dc00-dc07 : Creative Labs SB Live! MIDI/Game Port
e000-e00f : VIA Technologies, Inc. Bus Master IDE
e000-e007 : ide0
e008-e00f : ide1
e400-e41f : VIA Technologies, Inc. UHCI USB
e400-e41f : usb-uhci
e800-e81f : VIA Technologies, Inc. UHCI USB (#2)
e800-e81f : usb-uhci
ec00-ec1f : VIA Technologies, Inc. UHCI USB (#3)
ec00-ec1f : usb-uhci
$ cat /proc/iomem
00000000-0009fbff : System RAM
0009fc00-0009ffff : reserved
000a0000-000bffff : Video RAM area
000c0000-000c7fff : Video ROM
000cc000-000ccfff : Extension ROM
000f0000-000fffff : System ROM
00100000-0fffffff : System RAM
00100000-0022614c : Kernel code
0022614d-0029547f : Kernel data
e0000000-e3ffffff : VIA Technologies, Inc. VT8367 [KT266]
e4000000-e5ffffff : PCI Bus #01
e4000000-e5ffffff : nVidia Corporation Vanta [NV6]
e4000000-e4ffffff : vesafb
e6000000-e7ffffff : PCI Bus #01
e6000000-e6ffffff : nVidia Corporation Vanta [NV6]
e9000000-e90000ff : Realtek Semiconductor Co., Ltd. RTL-8139/8139C
e9000000-e90000ff : 8139too
ffff0000-ffffffff : reserved
# lspci -vvv
00:00.0 Host bridge: VIA Technologies, Inc. VT8367 [KT266]
Subsystem: VIA Technologies, Inc. VT8367 [KT266]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ >SERR- <PERR+
Latency: 8
Region 0: Memory at e0000000 (32-bit, prefetchable) [size=64M]
Capabilities: [a0] AGP version 2.0
Status: RQ=31 SBA+ 64bit- FW- Rate=x1,x2,x4
Command: RQ=0 SBA- AGP- 64bit- FW- Rate=<none>
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:01.0 PCI bridge: VIA Technologies, Inc. VT8367 [KT266 AGP] (prog-if
00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: e6000000-e7ffffff
Prefetchable memory behind bridge: e4000000-e5ffffff
BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:09.0 SCSI storage controller: Distributed Processing Technology
SmartCache/Raid I-IV Controller (rev 02)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (1000ns min, 2000ns max), cache line size 08
Interrupt: pin A routed to IRQ 11
BIST result: 00
Region 0: I/O ports at d000 [size=32]
Expansion ROM at <unassigned> [disabled] [size=32K]
00:0a.0 Ethernet controller: Realtek Semiconductor Co., Ltd.
RTL-8139/8139C (rev 10)
Subsystem: Realtek Semiconductor Co., Ltd. RT8139
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (8000ns min, 16000ns max)
Interrupt: pin A routed to IRQ 10
Region 0: I/O ports at d400 [size=256]
Region 1: Memory at e9000000 (32-bit, non-prefetchable)
[size=256]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA
PME(D0-,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:0b.0 Multimedia audio controller: Creative Labs SB Live! EMU10k1 (rev
07)
Subsystem: Creative Labs CT4780 SBLive! Value
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (500ns min, 5000ns max)
Interrupt: pin A routed to IRQ 5
Region 0: I/O ports at d800 [size=32]
Capabilities: [dc] Power Management version 1
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:0b.1 Input device controller: Creative Labs SB Live! MIDI/Game Port
(rev 07)
Subsystem: Creative Labs Gameport Joystick
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Region 0: I/O ports at dc00 [size=8]
Capabilities: [dc] Power Management version 1
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:11.0 ISA bridge: VIA Technologies, Inc. VT8233 PCI to ISA Bridge
Subsystem: VIA Technologies, Inc. VT8233 PCI to ISA Bridge
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping+ SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:11.1 IDE interface: VIA Technologies, Inc. Bus Master IDE (rev 06)
(prog-if 8a [Master SecP PriP])
Subsystem: VIA Technologies, Inc. Bus Master IDE
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Interrupt: pin A routed to IRQ 0
Region 4: I/O ports at e000 [size=16]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:11.2 USB Controller: VIA Technologies, Inc. USB (rev 1b) (prog-if 00
[UHCI])
Subsystem: VIA Technologies, Inc. (Wrong ID) USB Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32, cache line size 08
Interrupt: pin D routed to IRQ 9
Region 4: I/O ports at e400 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:11.3 USB Controller: VIA Technologies, Inc. USB (rev 1b) (prog-if 00
[UHCI])
Subsystem: VIA Technologies, Inc. (Wrong ID) USB Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32, cache line size 08
Interrupt: pin D routed to IRQ 9
Region 4: I/O ports at e800 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:11.4 USB Controller: VIA Technologies, Inc. USB (rev 1b) (prog-if 00
[UHCI])
Subsystem: VIA Technologies, Inc. (Wrong ID) USB Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32, cache line size 08
Interrupt: pin D routed to IRQ 9
Region 4: I/O ports at ec00 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
01:00.0 VGA compatible controller: nVidia Corporation NV6 [Vanta] (rev
15) (prog-if 00 [VGA])
Subsystem: Micro-star International Co Ltd MSI-8808
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (1250ns min, 250ns max)
Interrupt: pin A routed to IRQ 11
Region 0: Memory at e6000000 (32-bit, non-prefetchable)
[size=16M]
Region 1: Memory at e4000000 (32-bit, prefetchable) [size=32M]
Expansion ROM at <unassigned> [disabled] [size=64K]
Capabilities: [60] Power Management version 1
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [44] AGP version 2.0
Status: RQ=31 SBA- 64bit- FW- Rate=x1,x2,x4
Command: RQ=0 SBA- AGP- 64bit- FW- Rate=<none>
next reply other threads:[~2002-11-29 20:15 UTC|newest]
Thread overview: 2+ messages / expand[flat|nested] mbox.gz Atom feed top
2002-11-29 20:15 Jim Halfpenny [this message]
2002-11-29 21:24 ` UDMA causes IDE corruption on Shuttle AK32L mobo (VIA KT266A), kernel 2.4.1[89] Alan Cox
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1038600903.2074.2.camel@fox \
--to=jimvin@lineone.net \
--cc=linux-ide@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.