From: Niel Lambrechts <antispam@absamail.co.za>
To: Linux Kernel ML <linux-kernel@vger.kernel.org>
Subject: [BUG 2.6.6-rc2-mm1] rmmod processor causes kernel panic on speedstep-centrino
Date: Sun, 02 May 2004 23:11:58 +0200 [thread overview]
Message-ID: <1083532317.18059.12.camel@localhost> (raw)
Hi,
Problem:
rmmod processor causes kernel panic on speedstep-centrino
Description:
I read somewhere that module "processor" affects madwifi performance, so
I decided to remove the module. (I had to rmmod thermal as well) This
caused a kernel panic, yet the thinkpad is still up and seemingly, fully
functional and used to submit this report with.
Kernel version:
2.6.6-rc2-mm1, with own dsdt.
Output: (after rmmod processor)
Badness in remove_proc_entry at fs/proc/generic.c:685
Call Trace:
[<c01865fc>] remove_proc_entry+0x17c/0x190
[<e19d3940>] acpi_thermal_remove_fs+0x48/0x6b [thermal]
[<e19d3dcb>] acpi_thermal_remove+0xd0/0xed [thermal]
[<c02a73bb>] acpi_driver_detach+0x63/0xbc
[<c02a7501>] acpi_bus_unregister_driver+0x3c/0x92
[<e19d3e1b>] acpi_thermal_exit+0x33/0x53 [thermal]
[<c012fa59>] sys_delete_module+0x159/0x1b0
[<c01489f8>] do_munmap+0x158/0x1b0
[<c010619b>] syscall_call+0x7/0xb
Badness in remove_proc_entry at fs/proc/generic.c:685
Call Trace:
[<c01865fc>] remove_proc_entry+0x17c/0x190
[<e19dd323>] acpi_processor_remove_fs+0x48/0x6b [processor]
[<e19dd89c>] acpi_processor_remove+0x98/0xc7 [processor]
[<c02a73bb>] acpi_driver_detach+0x63/0xbc
[<c02a7501>] acpi_bus_unregister_driver+0x3c/0x92
[<e19dd96d>] acpi_processor_exit+0x3d/0x5d [processor]
[<c012fa59>] sys_delete_module+0x159/0x1b0
[<c01489f8>] do_munmap+0x158/0x1b0
[<c010619b>] syscall_call+0x7/0xb
Unable to handle kernel paging request at virtual address e19db3e6
printing eip:
e19db3e6
*pde = 1fdc8067
*pte = 00000000
Oops: 0000 [#1]
PREEMPT
CPU: 0
EIP: 0060:[<e19db3e6>] Tainted: PF VLI
EFLAGS: 00010296 (2.6.6-rc2-mm1)
EIP is at 0xe19db3e6
eax: 00000000 ebx: 00ba74be ecx: 00000000 edx: 00000000
esi: dfca76f8 edi: 00ba71ed ebp: dfca7600 esp: c04e5fc0
ds: 007b es: 007b ss: 0068
Process swapper (pid: 0, threadinfo=c04e4000 task=c0455a40)
Stack: 00569007 00000000 c04e4000 0009ef00 c0512120 00569007 c01040dd
00000816
c04e684e c0455a40 00000000 c050ac64 00000040 c04e6450 c0513020
c010019f
Call Trace:
[<c01040dd>] cpu_idle+0x2d/0x40
[<c04e684e>] start_kernel+0x18e/0x1d0
[<c04e6450>] unknown_bootoption+0x0/0x130
Code: Bad EIP value.
<0>Kernel panic: Attempted to kill the idle task!
In idle task - not syncing
<6>ACPI: Processor [CPU] (supports C1 C2 C3, 8 throttling states)
ACPI: Thermal Zone [THM0] (39 C)
osl-0889 [4473527] os_wait_semaphore : Failed to acquire
semaphore[dff5ee40|1|0], AE_TIME
osl-0889 [4492698] os_wait_semaphore : Failed to acquire
semaphore[dff5ee40|1|0], AE_TIME
osl-0889 [4517096] os_wait_semaphore : Failed to acquire
semaphore[dff5ee40|1|0], AE_TIME
Activity at time of problem:
ath_pci : madwifi wireless driver modules in use: ath_pci, ath_hal, wlan
boot options: acpi=yes, resume=/dev/hda2 (i use swsusp)
Environment:
Thinkpad R50P
SuSE 9.0 pro
Software:
# ./ver_linux
If some fields are empty or look unusual you may have an old version.
Compare to the current minimal requirements in Documentation/Changes.
Linux ksyrium 2.6.6-rc2-mm1 #10 Mon Apr 26 09:41:13 SAST 2004 i686 i686
i386 GNU/Linux
Gnu C 3.3.1
Gnu make 3.80
binutils 2.14.90.0.5
util-linux 2.11z
mount 2.11z
module-init-tools 0.9.14-pre2
e2fsprogs 1.34
jfsutils 1.1.2
xfsprogs 2.5.6
pcmcia-cs 3.2.4
PPP 2.4.1
isdn4k-utils 3.3
nfs-utils 1.0.6
Linux C Library x 1 root root 1470060 Oct 2 2003
/lib/libc.so.6
Dynamic linker (ldd) 2.3.2
Linux C++ Library 5.0.5
Procps 3.1.14
Net-tools 1.60
Kbd 1.08
Sh-utils 5.0
Modules Loaded thermal processor ath_pci wlan ath_hal ipaq vmnet
vmmon nls_iso8859_15 nls_cp437 vfat fat sd_mod usb_storage snd_pcm_oss
e1000 snd_mixer_oss nvram usbserial ipv6 snd_intel8x0 snd_ac97_codec
snd_pcm snd_timer snd_page_alloc snd_mpu401_uart snd_rawmidi
snd_seq_device snd soundcore uhci_hcd ohci_hcd ehci_hcd usbcore
speedstep_centrino battery fan ac button ide_scsi nls_iso8859_1
Processor:
# cat /proc/cpuinfo
processor : 0
vendor_id : GenuineIntel
cpu family : 6
model : 9
model name : Intel(R) Pentium(R) M processor 1700MHz
stepping : 5
cpu MHz : 598.161
cache size : 1024 KB
fdiv_bug : no
hlt_bug : no
f00f_bug : no
coma_bug : no
fpu : yes
fpu_exception : yes
cpuid level : 2
wp : yes
flags : fpu vme de pse tsc msr mce cx8 sep mtrr pge mca cmov
pat clflush dts acpi mmx fxsr sse sse2 tm pbe tm2 est
bogomips : 1185.43
Module info:
# cat /proc/modules
thermal 18064 0 - Live 0xe19d2000
processor 25264 1 thermal, Live 0xe1bc9000
ath_pci 40996 0 - Live 0xe1a7c000
wlan 64104 2 ath_pci, Live 0xe1b34000
ath_hal 129040 2 ath_pci, Live 0xe1bee000
ipaq 11864 0 - Live 0xe1bc5000
vmnet 30864 12 - Live 0xe1ac3000
vmmon 48920 0 - Live 0xe1ba7000
nls_iso8859_15 4672 0 - Live 0xe1a50000
nls_cp437 5760 0 - Live 0xe1a4d000
vfat 16256 0 - Live 0xe1a59000
fat 46720 1 vfat, Live 0xe1b9a000
sd_mod 19456 0 - Live 0xe1a53000
usb_storage 71904 0 - Live 0xe1b87000
snd_pcm_oss 63588 0 - Live 0xe1b23000
e1000 86220 0 - Live 0xe1a65000
snd_mixer_oss 21952 4 snd_pcm_oss, Live 0xe1afb000
nvram 9288 1 - Live 0xe1aa0000
usbserial 29552 1 ipaq, Live 0xe1aac000
ipv6 261216 10 - Live 0xe1b46000
snd_intel8x0 36996 4 - Live 0xe1ab8000
snd_ac97_codec 68164 1 snd_intel8x0, Live 0xe1ae9000
snd_pcm 109924 3 snd_pcm_oss,snd_intel8x0, Live 0xe1acd000
snd_timer 28612 1 snd_pcm, Live 0xe1aa4000
snd_page_alloc 12420 2 snd_intel8x0,snd_pcm, Live 0xe19eb000
snd_mpu401_uart 8832 1 snd_intel8x0, Live 0xe1a3a000
snd_rawmidi 27040 1 snd_mpu401_uart, Live 0xe1a43000
snd_seq_device 8776 1 snd_rawmidi, Live 0xe1a36000
snd 65860 10
snd_pcm_oss,snd_mixer_oss,snd_intel8x0,snd_ac97_codec,snd_pcm,snd_timer,snd_mpu401_uart,snd_rawmidi,snd_seq_device, Live 0xe1a88000
soundcore 10016 4 snd, Live 0xe19f0000
uhci_hcd 32984 0 - Live 0xe1a2c000
ohci_hcd 33820 0 - Live 0xe1a02000
ehci_hcd 41800 0 - Live 0xe19f6000
usbcore 121396 8 ipaq,usb_storage,usbserial,uhci_hcd,ohci_hcd,ehci_hcd,
Live 0xe1a0d000
speedstep_centrino 5700 0 - Live 0xe19e6000
battery 12108 0 - Live 0xe19c5000
fan 5324 0 - Live 0xe19d8000
ac 6348 0 - Live 0xe19c9000
button 8024 0 - Live 0xe198e000
ide_scsi 17668 0 - Live 0xe19cc000
nls_iso8859_1 4096 3 - Live 0xe1991000
Loaded drivers:
# cat /proc/ioports
0000-001f : dma1
0020-0021 : pic1
0040-005f : timer
0060-006f : keyboard
0070-0077 : rtc
0080-008f : dma page reg
00a0-00a1 : pic2
00c0-00df : dma2
00f0-00ff : fpu
0170-0177 : ide1
01f0-01f7 : ide0
0376-0376 : ide1
03bc-03be : parport0
03c0-03df : vesafb
03e0-03e1 : i82365
03f6-03f6 : ide0
03f8-03ff : serial
04d0-04d1 : pnp 00:0b
0cf8-0cff : PCI conf1
1000-107f : 0000:00:1f.0
1000-105f : pnp 00:0b
1060-107f : pnp 00:0b
1180-11bf : 0000:00:1f.0
1180-11bf : pnp 00:0b
1800-181f : 0000:00:1d.0
1800-181f : uhci_hcd
1820-183f : 0000:00:1d.1
1820-183f : uhci_hcd
1840-185f : 0000:00:1d.2
1840-185f : uhci_hcd
1860-186f : 0000:00:1f.1
1860-1867 : ide0
1868-186f : ide1
1880-189f : 0000:00:1f.3
18c0-18ff : 0000:00:1f.5
1c00-1cff : 0000:00:1f.5
2000-207f : 0000:00:1f.6
2400-24ff : 0000:00:1f.6
3000-3fff : PCI Bus #01
3000-30ff : 0000:01:00.0
4000-40ff : PCI CardBus #03
4400-44ff : PCI CardBus #03
4800-48ff : PCI CardBus #07
4c00-4cff : PCI CardBus #07
8000-803f : 0000:02:01.0
8000-803f : e1000
# cat /proc/iomem
00000000-0009efff : System RAM
0009f000-0009ffff : reserved
000a0000-000bffff : Video RAM area
000c0000-000cffff : Video ROM
000d0000-000d0fff : Adapter ROM
000d1000-000d1fff : Adapter ROM
000d2000-000d3fff : reserved
000e0000-000effff : Extension ROM
000f0000-000fffff : System ROM
00100000-1ff5ffff : System RAM
00100000-003d39ac : Kernel code
003d39ad-004e213f : Kernel data
1ff60000-1ff77fff : ACPI Tables
1ff78000-1ff79fff : ACPI Non-volatile Storage
1ff80000-1fffffff : reserved
20000000-200003ff : 0000:00:1f.1
20400000-207fffff : PCI CardBus #03
20800000-20bfffff : PCI CardBus #03
20c00000-20ffffff : PCI CardBus #07
21000000-213fffff : PCI CardBus #07
b0000000-b0000fff : 0000:02:00.0
b0000000-b0000fff : yenta_socket
b1000000-b1000fff : 0000:02:00.1
b1000000-b1000fff : yenta_socket
c0000000-c00003ff : 0000:00:1d.7
c0000000-c00003ff : ehci_hcd
c0000800-c00008ff : 0000:00:1f.5
c0000800-c00008ff : Intel 82801DB-ICH4 - Controller
c0000c00-c0000dff : 0000:00:1f.5
c0000c00-c0000dff : Intel 82801DB-ICH4 - AC'97
c0100000-c01fffff : PCI Bus #01
c0100000-c010ffff : 0000:01:00.0
c0200000-c020ffff : 0000:02:01.0
c0200000-c020ffff : e1000
c0210000-c021ffff : 0000:02:02.0
c0210000-c021ffff : ath
c0220000-c023ffff : 0000:02:01.0
c0220000-c023ffff : e1000
d0000000-dfffffff : 0000:00:00.0
e0000000-e7ffffff : PCI Bus #01
e0000000-e7ffffff : 0000:01:00.0
e0000000-e0ffffff : vesafb
ff800000-ffffffff : reserved
PCI information:
#lspci -vvv
00:00.0 Host bridge: Intel Corp. 82855PM Processor to I/O Controller
(rev 03)
Subsystem: IBM: Unknown device 0529
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ >SERR- <PERR-
Latency: 0
Region 0: Memory at d0000000 (32-bit, prefetchable) [size=256M]
Capabilities: [e4] #09 [4104]
Capabilities: [a0] AGP version 2.0
Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit-
FW+ AGP3- Rate=x1,x2,x4
Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=x1
00:01.0 PCI bridge: Intel Corp. 82855PM Processor to AGP Controller (rev
03) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 96
Bus: primary=00, secondary=01, subordinate=01, sec-latency=64
I/O behind bridge: 00003000-00003fff
Memory behind bridge: c0100000-c01fffff
Prefetchable memory behind bridge: e0000000-e7ffffff
BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
00:1d.0 USB Controller: Intel Corp. 82801DB USB (Hub #1) (rev 01)
(prog-if 00 [UHCI])
Subsystem: IBM: Unknown device 052d
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 11
Region 4: I/O ports at 1800 [size=32]
00:1d.1 USB Controller: Intel Corp. 82801DB USB (Hub #2) (rev 01)
(prog-if 00 [UHCI])
Subsystem: IBM: Unknown device 052d
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 11
Region 4: I/O ports at 1820 [size=32]
00:1d.2 USB Controller: Intel Corp. 82801DB USB (Hub #3) (rev 01)
(prog-if 00 [UHCI])
Subsystem: IBM: Unknown device 052d
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin C routed to IRQ 11
Region 4: I/O ports at 1840 [size=32]
00:1d.7 USB Controller: Intel Corp. 82801DB USB2 (rev 01) (prog-if 20
[EHCI])
Subsystem: IBM: Unknown device 052e
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin D routed to IRQ 11
Region 0: Memory at c0000000 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] #0a [2080]
00:1e.0 PCI bridge: Intel Corp. 82801BAM/CAM PCI Bridge (rev 81)
(prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR+
Latency: 0
Bus: primary=00, secondary=02, subordinate=08, sec-latency=168
I/O behind bridge: 00004000-00008fff
Memory behind bridge: c0200000-cfffffff
Prefetchable memory behind bridge: e8000000-efffffff
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
00:1f.0 ISA bridge: Intel Corp. 82801DBM LPC Interface Controller (rev
01)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
00:1f.1 IDE interface: Intel Corp. 82801DBM Ultra ATA Storage Controller
(rev 01) (prog-if 8a [Master SecP PriP])
Subsystem: IBM: Unknown device 052d
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at <unassigned>
Region 1: I/O ports at <unassigned>
Region 2: I/O ports at <unassigned>
Region 3: I/O ports at <unassigned>
Region 4: I/O ports at 1860 [size=16]
Region 5: Memory at 20000000 (32-bit, non-prefetchable) [size=1K]
00:1f.3 SMBus: Intel Corp. 82801DB/DBM SMBus Controller (rev 01)
Subsystem: IBM: Unknown device 052d
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin B routed to IRQ 5
Region 4: I/O ports at 1880 [size=32]
00:1f.5 Multimedia audio controller: Intel Corp. 82801DB AC'97 Audio
Controller (rev 01)
Subsystem: IBM: Unknown device 0554
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 5
Region 0: I/O ports at 1c00 [size=256]
Region 1: I/O ports at 18c0 [size=64]
Region 2: Memory at c0000c00 (32-bit, non-prefetchable) [size=512]
Region 3: Memory at c0000800 (32-bit, non-prefetchable) [size=256]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:1f.6 Modem: Intel Corp. 82801DB AC'97 Modem Controller (rev 01)
(prog-if 00 [Generic])
Subsystem: IBM: Unknown device 0525
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin B routed to IRQ 5
Region 0: I/O ports at 2400 [size=256]
Region 1: I/O ports at 2000 [size=128]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
01:00.0 VGA compatible controller: ATI Technologies Inc: Unknown device
4e54 (rev 80) (prog-if 00 [VGA])
Subsystem: IBM: Unknown device 054f
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B+
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 66 (2000ns min), cache line size 08
Interrupt: pin A routed to IRQ 11
Region 0: Memory at e0000000 (32-bit, prefetchable) [size=128M]
Region 1: I/O ports at 3000 [size=256]
Region 2: Memory at c0100000 (32-bit, non-prefetchable) [size=64K]
Expansion ROM at <unassigned> [disabled] [size=128K]
Capabilities: [58] AGP version 2.0
Status: RQ=80 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit-
FW+ AGP3- Rate=x1,x2,x4
Command: RQ=1 ArqSz=0 Cal=0 SBA+ AGP- GART64- 64bit- FW- Rate=<none>
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
02:00.0 CardBus bridge: Texas Instruments: Unknown device ac46 (rev 01)
Subsystem: IBM: Unknown device 0552
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 168, cache line size 10
Interrupt: pin A routed to IRQ 11
Region 0: Memory at b0000000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=02, secondary=03, subordinate=06, sec-latency=176
Memory window 0: 20400000-207ff000 (prefetchable)
Memory window 1: 20800000-20bff000
I/O window 0: 00004000-000040ff
I/O window 1: 00004400-000044ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite+
16-bit legacy interface ports at 03e1
02:00.1 CardBus bridge: Texas Instruments: Unknown device ac46 (rev 01)
Subsystem: IBM: Unknown device 0552
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 168, cache line size 10
Interrupt: pin B routed to IRQ 5
Region 0: Memory at b1000000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=02, secondary=07, subordinate=0a, sec-latency=176
Memory window 0: 20c00000-20fff000 (prefetchable)
Memory window 1: 21000000-213ff000
I/O window 0: 00004800-000048ff
I/O window 1: 00004c00-00004cff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite+
16-bit legacy interface ports at 03e1
02:01.0 Ethernet controller: Intel Corp.: Unknown device 101e (rev 03)
Subsystem: IBM: Unknown device 0549
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (63750ns min), cache line size 08
Interrupt: pin A routed to IRQ 11
Region 0: Memory at c0220000 (32-bit, non-prefetchable) [size=128K]
Region 1: Memory at c0200000 (32-bit, non-prefetchable) [size=64K]
Region 2: I/O ports at 8000 [size=64]
Expansion ROM at <unassigned> [disabled] [size=64K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [f0] Message Signalled Interrupts: 64bit+ Queue=0/0
Enable-
Address: 0000000000000000 Data: 0000
02:02.0 Ethernet controller: Unknown device 168c:1014 (rev 01)
Subsystem: Unknown device 17ab:8331
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 168 (2500ns min, 7000ns max), cache line size 08
Interrupt: pin A routed to IRQ 11
Region 0: Memory at c0210000 (32-bit, non-prefetchable) [size=64K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
SCSI info:
Unused
Regards,
Niel
next reply other threads:[~2004-05-02 21:13 UTC|newest]
Thread overview: 3+ messages / expand[flat|nested] mbox.gz Atom feed top
2004-05-02 21:11 Niel Lambrechts [this message]
2004-05-02 22:11 ` [BUG 2.6.6-rc2-mm1] rmmod processor causes kernel panic on speedstep-centrino Denis Vlasenko
2004-05-02 22:32 ` Patrick Dreker
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1083532317.18059.12.camel@localhost \
--to=antispam@absamail.co.za \
--cc=linux-kernel@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.