From: Marcel Holtmann <marcel@holtmann.org>
To: "Rolf E. Thorup" <rolft@daimi.au.dk>
Cc: BlueZ Mailing List <bluez-users@lists.sourceforge.net>
Subject: Re: [Bluez-users] SDP problems on embedded device
Date: Tue, 20 Jul 2004 16:47:43 +0200 [thread overview]
Message-ID: <1090334863.4400.124.camel@pegasus> (raw)
In-Reply-To: <40FCF471.4010501@daimi.au.dk>
Hi Rolf,
> Here's the output from the laptop (browsing the Cerfcube):
>
> HCIDump - HCI packet analyzer ver 1.9
> device: hci0 snap_len: 1028 filter: 0xffffffff
> 1090319067.842941 < HCI Command: Create Connection (0x01|0x0005) plen 13
> 2A 20 00 94 0A 00 18 CC 00 00 00 00 01
> 1090319067.846445 > HCI Event: Command Status (0x0f) plen 4
> 00 01 05 04
> 1090319068.636871 > HCI Event: Connect Complete (0x03) plen 11
> 00 29 00 2A 20 00 94 0A 00 01 00
> 1090319068.637297 < ACL data: handle 0x0029 flags 0x02 dlen 12
> L2CAP(s): Connect req: psm 1 scid 0x0040
> 1090319068.637345 < HCI Command: Write Link Policy Settings
> (0x02|0x000d) plen 4
> 29 00 0F 00
> 1090319068.648902 > HCI Event: Number of Completed Packets (0x13) plen 5
> 01 29 00 01 00
> 1090319068.658112 > HCI Event: Command Complete (0x0e) plen 6
> 01 0D 08 00 29 00
> 1090319068.666028 > HCI Event: Page Scan Repetition Mode Change (0x20)
> plen 7
> 2A 20 00 94 0A 00 01
> 1090319068.667769 > HCI Event: Max Slots Change (0x1b) plen 3
> 29 00 05
> 1090319068.715975 > ACL data: handle 0x0029 flags 0x02 dlen 16
> L2CAP(s): Connect rsp: dcid 0x0040 scid 0x0040 result 0 status 0
> 1090319068.716411 < ACL data: handle 0x0029 flags 0x02 dlen 12
> L2CAP(s): Config req: dcid 0x0040 flags 0x0000 clen 0
> 1090319068.722627 > HCI Event: Number of Completed Packets (0x13) plen 5
> 01 29 00 01 00
> 1090319068.745926 > ACL data: handle 0x0029 flags 0x02 dlen 14
> L2CAP(s): Config rsp: scid 0x0040 flags 0x0000 result 0 clen 0
> 1090319107.835421 < ACL data: handle 0x0029 flags 0x02 dlen 12
> L2CAP(s): Disconn req: dcid 0x0040 scid 0x0040
> 1090319107.849809 > HCI Event: Number of Completed Packets (0x13) plen 5
> 01 29 00 01 00
> 1090319107.866512 > ACL data: handle 0x0029 flags 0x02 dlen 12
> L2CAP(s): Disconn rsp: dcid 0x0040 scid 0x0040
> 1090319109.835420 < HCI Command: Disconnect (0x01|0x0006) plen 3
> 29 00 13
> 1090319109.837924 > HCI Event: Command Status (0x0f) plen 4
> 00 01 06 04
> 1090319109.875959 > HCI Event: Disconn Complete (0x05) plen 4
> 00 29 00 16
>
> and here's the output from the Cerfcube:
>
> HCIDump - HCI packet analyzer ver 1.9
> device: hci0 snap_len: 1028 filter: 0xffffffff
> 1090319478.496750 > HCI Event: Connect Request (0x04) plen 10
> 74 05 B1 76 0C 00 00 01 00 01
> 1090319478.497886 < HCI Command: Accept Connection Request (0x01|0x0009)
> plen 7
> 74 05 B1 76 0C 00 01
> 1090319478.512733 > HCI Event: Command Status (0x0f) plen 4
> 00 01 09 04
> 1090319478.546741 > HCI Event: Connect Complete (0x03) plen 11
> 00 29 00 74 05 B1 76 0C 00 01 00
> 1090319478.547821 < HCI Command: Write Link Policy Settings
> (0x02|0x000d) plen 4
> 29 00 0F 00
> 1090319478.550769 > HCI Event: Page Scan Repetition Mode Change (0x20)
> plen 7
> 74 05 B1 76 0C 00 01
> 1090319478.564746 > HCI Event: Command Complete (0x0e) plen 6
> 01 0D 08 00 29 00
> 1090319478.565797 < HCI Command: Change Connection Packet Type
> (0x01|0x000f) plen 4
> 29 00 18 CC
> 1090319478.584718 > HCI Event: Max Slots Change (0x1b) plen 3
> 29 00 05
> 1090319478.588740 > HCI Event: Command Status (0x0f) plen 4
> 00 01 0F 04
> 1090319478.592739 > HCI Event: Connection Packet Type Changed (0x1d) plen 5
> 00 29 00 18 CC
> 1090319478.602746 > ACL data: handle 0x0029 flags 0x02 dlen 12
> L2CAP(s): Connect req: psm 1 scid 0x0040
> 1090319478.604041 < ACL data: handle 0x0029 flags 0x02 dlen 16
> L2CAP(s): Connect rsp: dcid 0x0040 scid 0x0040 result 0 status 0
> 1090319478.612733 > HCI Event: Number of Completed Packets (0x13) plen 5
> 01 29 00 01 00
> 1090319478.618741 > ACL data: handle 0x0029 flags 0x02 dlen 12
> L2CAP(s): Config req: dcid 0x0040 flags 0x0000 clen 0
> 1090319478.619937 < ACL data: handle 0x0029 flags 0x02 dlen 14
> L2CAP(s): Config rsp: scid 0x0040 flags 0x0000 result 0 clen 0
> 1090319478.620053 < ACL data: handle 0x0029 flags 0x02 dlen 12
> L2CAP(s): Config req: dcid 0x0040 flags 0x0000 clen 0
the problem is that this "Config req" request never reaches the other
side. And because of that the laptop sides sends a "Disonn req" after
some time.
> 1090319478.642724 > HCI Event: Number of Completed Packets (0x13) plen 5
> 01 29 00 01 00
> 1090319517.746003 > ACL data: handle 0x0029 flags 0x02 dlen 12
> L2CAP(s): Disconn req: dcid 0x0040 scid 0x0040
> 1090319517.746236 < ACL data: handle 0x0029 flags 0x02 dlen 12
> L2CAP(s): Disconn rsp: dcid 0x0040 scid 0x0040
> 1090319517.768987 > HCI Event: Number of Completed Packets (0x13) plen 5
> 01 29 00 01 00
> 1090319519.848575 > HCI Event: Disconn Complete (0x05) plen 4
> 00 29 00 13
Try using 2.4.19-mh14 and show us the output of "hciconfig -a" on your
Cerfcube. Is the Cerfcube a big endian machine?
Regards
Marcel
-------------------------------------------------------
This SF.Net email is sponsored by BEA Weblogic Workshop
FREE Java Enterprise J2EE developer tools!
Get your free copy of BEA WebLogic Workshop 8.1 today.
http://ads.osdn.com/?ad_id=4721&alloc_id=10040&op=click
_______________________________________________
Bluez-users mailing list
Bluez-users@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/bluez-users
next prev parent reply other threads:[~2004-07-20 14:47 UTC|newest]
Thread overview: 13+ messages / expand[flat|nested] mbox.gz Atom feed top
2004-07-19 19:38 [Bluez-users] SDP problems on embedded device Rolf E. Thorup
2004-07-19 20:53 ` Marcel Holtmann
2004-07-20 10:31 ` Rolf E. Thorup
2004-07-20 14:47 ` Marcel Holtmann [this message]
2004-07-20 17:10 ` Rolf E. Thorup
2004-07-20 17:43 ` Marcel Holtmann
2004-07-21 9:43 ` Rolf E. Thorup
2004-07-21 10:04 ` Marcel Holtmann
2004-07-21 10:56 ` Rolf E. Thorup
2004-07-21 12:18 ` Marcel Holtmann
2004-07-21 12:30 ` Rolf E. Thorup
2004-07-28 14:05 ` Rolf E. Thorup
2004-07-28 18:57 ` Marcel Holtmann
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1090334863.4400.124.camel@pegasus \
--to=marcel@holtmann.org \
--cc=bluez-users@lists.sourceforge.net \
--cc=rolft@daimi.au.dk \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.