[U-Boot-Users] Blank console with IXDP425 in U-boot-1.1.6

[Queenie <queenie245@gmail.com>]

Yes.. U r right. Iam not using the ixdp425 (development) board.
What iam using is a customised board having IXP425.

On this board, I tried with the REDBOOT prebuilt utility for ixdp425 board (
development board) from the web and I could see the console message on my
hyperterminal. 

I was wondering y I cannot observe the same with my U-boot. is there any
extra configuration needed?

I checked the CFG_IXP425_CONSOLE macro in u-boot and saw thats its assigned
to IXP425_UART1 of the IXP425 chip. I also checked the circuit diagram of my
customised target platform and found that the console is connected to UART1
only.

What could be causing this problem? 


Stefan Roese wrote:
> 
> Hi Queenie,
> 
> On Monday 11 June 2007, Queenie wrote:
>> Iam a newbie in this field. I have a customed target board having IXP425.
>> This board has been working fine with Redboot. I do not have the working
>> source code for Redboot but only the bin file which works fine.
>> I now want to customise the u-boot and make u-boot the bootloader for
>> this
>> board.
>>
>> I have downloaded u-boot-1.1.6. Also I have downloaded the npe microcode
>> from intel website (IPL_ixp400NpeLibrary-2_4).
>> The tool chain I have downloaded is arm-linux-tools-20061213.tar.gz
>> I have added the toolchain in my $PATH (.bash_profile file)
>> I complied my u-boot for IXDP425 by giving the command "make
>> ixdp425_config" and the "make all"
> 
> Yes, but if I understand you correctly, then you don't have the Intel
> IXDP425 
> board, but a custom specific board. Correct? I assume that there are some 
> differences to the Intel board. What are those differences? You have to 
> *port* U-Boot to your specific hardware.
> 
>> It complied sucessfully and gave me a u-boot.bin and u-boot.srec file.
>>
>> I used this u-boot.bin file and loaded it into my target board flash
>> using
>> an ICE. after this is accomplished, I restarted the board and connected
>> the
>> console of my target board so that i could observe the bootloader prompt
>> on
>> the hyperterminal.
>> I see nothin on the console (hyperterminal)
>> I have connect it with baud rate 115200, 8 data bits, parity bits none, 1
>> stop bit and flow control as none. I even tried with flow control as
>> hardware.
>>
>> Please advise where i could be going wrong and how i should proceed.
> 
> As mentioned above, using a binary compiled for a different board will in
> most 
> cases not work.
> 
> Best regards,
> Stefan
> 
> =====================================================================
> DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
> HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
> Phone: +49-8142-66989-0 Fax: +49-8142-66989-80  Email: office at denx.de
> =====================================================================
> 
> -------------------------------------------------------------------------
> This SF.net email is sponsored by DB2 Express
> Download DB2 Express C - the FREE version of DB2 express and take
> control of your XML. No limits. Just data. Click to get it now.
> http://sourceforge.net/powerbar/db2/
> _______________________________________________
> U-Boot-Users mailing list
> U-Boot-Users at lists.sourceforge.net
> https://lists.sourceforge.net/lists/listinfo/u-boot-users
> 
> 

-- 
View this message in context: http://www.nabble.com/Blank-console-with-IXDP425-in-U-boot-1.1.6-tf3900825.html#a11059014
Sent from the Uboot - Users mailing list archive at Nabble.com.