All of lore.kernel.org
 help / color / mirror / Atom feed
From: Sergio Monteiro Basto <sergio@sergiomb.no-ip.org>
To: alsa-user <alsa-user@alsa-project.org>,
	alsa-devel <alsa-devel@lists.sourceforge.net>
Subject: VIA 8237 with CMedia CMI9761 Report issues, problems and some sucess
Date: Sun, 13 Feb 2005 03:34:54 +0000	[thread overview]
Message-ID: <1108265694.1791.30.camel@bastov> (raw)
In-Reply-To: <1108233173.874.3.camel@bastov>

Hi,

After search on https://bugtrack.alsa-project.org/ for CMI9761, I found
3 issues, all resolved ! 
The most similar is "ASRock k7vt4a+ with CMedia CMI9761 no mixer!", I
have one ASRock P4VT8+ with CMedia CMI9761.

Try boot with pci=noacpi (that put the interrupts on XT-PIC) but is not
one ACPI problem, because sound have same behavior with a normal boot. 

After play around with alsamixer, 
I got sound when unmute PCM and Off (mute) IEC958 Capture Monitor.

All others controls does change anything include mute or unmute the
Master.
Except VIA DXS (this one can do sound balance, left and right).  
VIA DXS 1, VIA DXS 2 and VIA DXS 3 also doesn't do nothing.

Play around with 
options snd-via82xx dxs_support
on file /etc/modprobe.conf
only with "options snd-via82xx dxs_support=2" I see any difference but
for worst, make disappear VIA DXS, VIA DXS 1, VIA DXS 2 and VIA DXS 3
controls.

Sorry for my weak English, if you don't understand something just ask
me, that I will try explain again.

lspci -nv
00:11.5 Class 0401: 1106:3059 (rev 60)
        Subsystem: 1849:9739
        Flags: medium devsel, IRQ 185
        I/O ports at c000 [size=256]
        Capabilities: [c0] Power Management version 2

lspci -vv
00:11.5 Multimedia audio controller: VIA Technologies, Inc. VT8233/A/8235/8237 AC97 Audio Controller (rev 60)
        Subsystem: ASRock Incorporation: Unknown device 9739
        Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Interrupt: pin C routed to IRQ 185
        Region 0: I/O ports at c000 [size=256]
        Capabilities: [c0] Power Management version 2
                Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-


Thanks,

On Sat, 2005-02-12 at 18:32 +0000, Sergio Monteiro Basto wrote:
> Hi 
> Fwd to alsa-devel can be more appropriated !
> any information about this VIA 8237 ?
> google around have a very few information and on alsa site either.
> 
> TIA,
> 
> -------- Forwarded Message --------
> > From: Sergio Monteiro Basto <sergio@sergiomb.no-ip.org>
> > Reply-To: sergio@sergiomb.no-ip.org
> > To: alsa-user <alsa-user@alsa-project.org>
> > Subject: [Alsa-user] VIA 8237 issues and problems
> > Date: Sat, 12 Feb 2005 03:25:19 +0000
> > Hi,
> > 
> > After trying everything , no sound still on my desktop
> > I with Fedora Core 3 , and even try install alsa-drive, lib, and utils
> > 1.0.8 from sources. 
> > 
> > about: 
> > kernel: Please try dxs_support=1 or dxs_support=4 option
> > kernel:          and report if it works on your machine.
> > 
> > adding options snd-via82xx dxs_support=1 or dxs_support=4 doesn't help.
> > 
> > system-config-soundcard give me this warning : 
> > Playing WAVE '/usr/share/system-config-soundcard/sound-sample.wav' :
> > Signed 16 bit Little Endian, Rate 44100 Hz, Stereo
> > Warning: rate is not accurate (requested = 44100Hz, got = 48000Hz)
> >          please, try the plug plugin (-Dplug:hw:0,0)
> > 
> > alsamixer says: 
> > 
> > Card: VIA 8237
> > Chip: C-Media Electronics CMI9761
> > 
> > lspci:
> > 00:00.0 Host bridge: VIA Technologies, Inc. VT8374 P4X400 Host Controller/AGP Bridge (rev 82)
> > 00:01.0 PCI bridge: VIA Technologies, Inc. VT8237 PCI Bridge
> > 00:0b.0 Communication controller: Conexant HSF 56k HSFi Modem (rev 01)
> > 00:0f.0 RAID bus controller: VIA Technologies, Inc. VIA VT6420 SATA RAID Controller (rev 80)
> > 00:0f.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06)
> > 00:10.0 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 81)
> > 00:10.1 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 81)
> > 00:10.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 81)
> > 00:10.3 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 81)
> > 00:10.4 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 86)
> > 00:11.0 ISA bridge: VIA Technologies, Inc. VT8237 ISA bridge [KT600/K8T800 South]
> > 00:11.5 Multimedia audio controller: VIA Technologies, Inc. VT8233/A/8235/8237 AC97 Audio Controller (rev 60)
> > 00:12.0 Ethernet controller: VIA Technologies, Inc. VT6102 [Rhine-II] (rev 78)
> > 
> > 
> > 
> > TIA,
-- 
Sérgio M.B.



-------------------------------------------------------
SF email is sponsored by - The IT Product Guide
Read honest & candid reviews on hundreds of IT Products from real users.
Discover which products truly live up to the hype. Start reading now.
http://ads.osdn.com/?ad_id=6595&alloc_id=14396&op=click

      reply	other threads:[~2005-02-13  3:34 UTC|newest]

Thread overview: 2+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2005-02-12 18:32 [Fwd: [Alsa-user] VIA 8237 issues and problems] Sergio Monteiro Basto
2005-02-13  3:34 ` Sergio Monteiro Basto [this message]

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=1108265694.1791.30.camel@bastov \
    --to=sergio@sergiomb.no-ip.org \
    --cc=alsa-devel@lists.sourceforge.net \
    --cc=alsa-user@alsa-project.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.