Re: [ACPI] Re: Fw: Anybody? 2.6.11 (stable and -rc) ACPI breaks USB

[Bjorn Helgaas <bjorn.helgaas@hp.com>]

On Fri, 2005-03-18 at 11:07 -0700, Bjorn Helgaas wrote:
> OK.  Try this one for size.  It differs from what's currently in
> the tree in these ways:
> 
>     - It's a quirk, so we don't have to clutter acpi_pci_irq_enable()
>       and pirq_enable_irq() with Via-specific code.
> 
>     - It doesn't do anything unless we're in PIC mode.  The comment
>       suggests this issue only affects PIC routing.
> 
>     - We do this for ALL Via devices.  The current code in the tree
>       does it for all devices in the system IF there is a Via device
>       with devfn==0, which misses Grzegorz's case.
> 
> Does anybody have a pointer to a spec that talks about this?  It'd
> be awfully nice to have a reference.
> 
> Grzegorz, can you check to make sure this still works after all the
> tweaking?

Oops, I had the sense of the skip_ioapic_setup test reversed.  Corrected
patch follows.

===== arch/i386/pci/irq.c 1.55 vs edited =====
--- 1.55/arch/i386/pci/irq.c	2005-02-07 22:39:15 -07:00
+++ edited/arch/i386/pci/irq.c	2005-03-15 10:11:44 -07:00
@@ -1026,7 +1026,6 @@
 static int pirq_enable_irq(struct pci_dev *dev)
 {
 	u8 pin;
-	extern int via_interrupt_line_quirk;
 	struct pci_dev *temp_dev;
 
 	pci_read_config_byte(dev, PCI_INTERRUPT_PIN, &pin);
@@ -1081,10 +1080,6 @@
 		printk(KERN_WARNING "PCI: No IRQ known for interrupt pin %c of device %s.%s\n",
 		       'A' + pin, pci_name(dev), msg);
 	}
-	/* VIA bridges use interrupt line for apic/pci steering across
-	   the V-Link */
-	else if (via_interrupt_line_quirk)
-		pci_write_config_byte(dev, PCI_INTERRUPT_LINE, dev->irq & 15);
 	return 0;
 }
 
===== drivers/acpi/pci_irq.c 1.37 vs edited =====
--- 1.37/drivers/acpi/pci_irq.c	2005-03-01 09:57:29 -07:00
+++ edited/drivers/acpi/pci_irq.c	2005-03-15 10:10:57 -07:00
@@ -388,7 +388,6 @@
 	u8			pin = 0;
 	int			edge_level = ACPI_LEVEL_SENSITIVE;
 	int			active_high_low = ACPI_ACTIVE_LOW;
-	extern int		via_interrupt_line_quirk;
 
 	ACPI_FUNCTION_TRACE("acpi_pci_irq_enable");
 
@@ -437,9 +436,6 @@
 			return_VALUE(0);
 		}
  	}
-
-	if (via_interrupt_line_quirk)
-		pci_write_config_byte(dev, PCI_INTERRUPT_LINE, irq & 15);
 
 	dev->irq = acpi_register_gsi(irq, edge_level, active_high_low);
 
===== drivers/pci/quirks.c 1.72 vs edited =====
--- 1.72/drivers/pci/quirks.c	2005-03-10 01:38:25 -07:00
+++ edited/drivers/pci/quirks.c	2005-03-21 09:22:23 -07:00
@@ -683,19 +683,40 @@
 }
 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL,	PCI_DEVICE_ID_INTEL_82454NX,	quirk_disable_pxb );
 
-/*
- *	VIA northbridges care about PCI_INTERRUPT_LINE
- */
-int via_interrupt_line_quirk;
+#ifdef CONFIG_ACPI
+#include <linux/acpi.h>
+#endif
 
-static void __devinit quirk_via_bridge(struct pci_dev *pdev)
+static void __devinit quirk_via_irqpic(struct pci_dev *dev)
 {
-	if(pdev->devfn == 0) {
-		printk(KERN_INFO "PCI: Via IRQ fixup\n");
-		via_interrupt_line_quirk = 1;
+	u8 irq, new_irq;
+
+#ifdef CONFIG_X86_IO_APIC
+	if (!skip_ioapic_setup)
+		return;
+#endif
+#ifdef CONFIG_ACPI
+	if (acpi_irq_model != ACPI_IRQ_MODEL_PIC)
+		return;
+#endif
+	/*
+	 * Some Via devices make an internal connection to the PIC when the
+	 * PCI_INTERRUPT_LINE register is written.  If we've changed the
+	 * device's IRQ, we need to update this routing.
+	 *
+	 * I suspect this only happens for devices on the same chip as the
+	 * PIC, but I don't know how to identify those without listing them
+	 * all individually, which is a maintenance problem.
+	 */
+	new_irq = dev->irq & 0xf;
+	pci_read_config_byte(dev, PCI_INTERRUPT_LINE, &irq);
+	if (new_irq != irq) {
+		printk(KERN_INFO "PCI: Via PIC IRQ fixup for %s, from %d to %d\n",
+			pci_name(dev), irq, new_irq);
+		pci_write_config_byte(dev, PCI_INTERRUPT_LINE, new_irq);
 	}
 }
-DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA,	PCI_ANY_ID,                     quirk_via_bridge );
+DECLARE_PCI_FIXUP_ENABLE(PCI_VENDOR_ID_VIA, PCI_ANY_ID, quirk_via_irqpic);
 
 /*
  *	Serverworks CSB5 IDE does not fully support native mode