From mboxrd@z Thu Jan 1 00:00:00 1970 From: Githogori Nyangara-Murage Subject: RE: xen 3.0 boot problem Date: Fri, 07 Oct 2005 00:22:48 -0700 Message-ID: <1128669768.5392.10.camel@linux.site> References: Reply-To: githogori@xensource.com Mime-Version: 1.0 Content-Type: text/plain Content-Transfer-Encoding: 7bit Return-path: In-Reply-To: List-Unsubscribe: , List-Post: List-Help: List-Subscribe: , Sender: xen-users-bounces@lists.xensource.com Errors-To: xen-users-bounces@lists.xensource.com To: Ian Pratt Cc: githogori@xensource.com, xen-devel@lists.xensource.com, Stephan =?ISO-8859-1?Q?B=F6ni?= , ian.pratt@cl.cam.ac.uk, xen-users@lists.xensource.com List-Id: xen-devel@lists.xenproject.org As I had stated earlier, I have again built Xen-unstable and have it running on a Dell 1850 which has a qla2300 card. In fact right now it is busy beating up on the storage using ibre channel via the qla2300. It is on RHEL 4.1, and build against a vanilla Cambridge download, so this should also work on SuSE. Below is a snippet of my messages file. .githogori. Oct 6 22:19:58 localhost kernel: Red Hat/Adaptec aacraid driver (1.1.2-lk2 Oct 6 2005) Oct 6 22:19:58 localhost kernel: QLogic Fibre Channel HBA Driver Oct 6 22:19:58 localhost kernel: ACPI: PCI Interrupt 0000:02:0b.0[A] -> GSI 37 (level, low) -> IRQ 37 Oct 6 22:19:58 localhost kernel: qla2300 0000:02:0b.0: Found an ISP2312, irq 37, iobase 0xe0002000 Oct 6 22:19:58 localhost kernel: scsi0 : qla2xxx Oct 6 22:19:58 localhost kernel: qla2300 0000:02:0b.0: Configuring PCI space... Oct 6 22:19:58 localhost kernel: qla2300 0000:02:0b.0: Configure NVRAM parameters... Oct 6 22:19:58 localhost kernel: qla2300 0000:02:0b.0: Verifying loaded RISC code... Oct 6 22:19:58 localhost kernel: qla2300 0000:02:0b.0: Waiting for LIP to complete... Oct 6 22:19:58 localhost kernel: qla2300 0000:02:0b.0: Cable is unplugged... Oct 6 22:19:58 localhost kernel: qla2300 0000:02:0b.0: Oct 6 22:19:58 localhost kernel: QLogic Fibre Channel HBA Driver: 8.00.02b5-k Oct 6 22:19:58 localhost kernel: QLogic QLA2342 - 133MHz PCI-X to 2Gb FC, Dual Channel Oct 6 22:19:58 localhost kernel: ISP2312: PCI-X (133 MHz) @ 0000:02:0b.0 hdma-, host#=0, fw=3.03.08 IPX Oct 6 22:19:58 localhost kernel: ACPI: PCI Interrupt 0000:02:0b.1[B] -> GSI 38 (level, low) -> IRQ 38 Oct 6 22:19:58 localhost kernel: qla2300 0000:02:0b.1: Found an ISP2312, irq 38, iobase 0xe0004000 Oct 6 22:19:59 localhost kernel: scsi1 : qla2xxx Oct 6 22:19:59 localhost kernel: qla2300 0000:02:0b.1: Configuring PCI space... Oct 6 22:19:59 localhost kernel: qla2300 0000:02:0b.1: Configure NVRAM parameters... Oct 6 22:19:59 localhost kernel: qla2300 0000:02:0b.1: Verifying loaded RISC code... Oct 6 22:19:59 localhost kernel: qla2300 0000:02:0b.1: Waiting for LIP to complete... Oct 6 22:19:59 localhost kernel: qla2300 0000:02:0b.1: LIP reset occured (f8f7). Oct 6 22:19:59 localhost kernel: qla2300 0000:02:0b.1: LIP occured (f8f7). Oct 6 22:19:59 localhost kernel: qla2300 0000:02:0b.1: LOOP UP detected (1 Gbps). Oct 6 22:19:59 localhost kernel: qla2300 0000:02:0b.1: Topology - (Loop), Host Loop address 0x7d Oct 6 22:19:59 localhost kernel: qla2300 0000:02:0b.1: Oct 6 22:19:59 localhost kernel: QLogic Fibre Channel HBA Driver: 8.00.02b5-k Oct 6 22:19:59 localhost kernel: QLogic QLA2342 - 133MHz PCI-X to 2Gb FC, Dual Channel Oct 6 22:19:59 localhost kernel: ISP2312: PCI-X (133 MHz) @ 0000:02:0b.1 hdma-, host#=1, fw=3.03.08 IPX Oct 6 22:19:59 localhost kernel: megaraid cmm: 2.20.2.5 (Release Date: Fri Jan 21 00:01:03 EST 2005) Oct 6 22:19:59 localhost kernel: megaraid: 2.20.4.5 (Release Date: Thu Feb 03 12:27:22 EST 2005) Oct 6 22:19:59 localhost kernel: Vendor: DGC Model: RAID 5 Rev: 0411 Oct 6 22:19:59 localhost kernel: Type: Direct-Access ANSI SCSI revision: 02 Oct 6 22:19:59 localhost kernel: 3ware Storage Controller device driver for Linux v1.26.02.001. Oct 6 22:19:59 localhost kernel: SCSI device sda: 68317440 512-byte hdwr sectors (34979 MB) On Wed, 2005-10-05 at 21:28 +0100, Ian Pratt wrote: > Has anyone used xen succefully with a qla2300? > > What machines have this card? > > Ian > > > I've installed Xen 3.0-devel on SUSE Linux without any problems. > > But when i tryed to boot the system, i've got a funny problem: > > > > qla2300 0000:05:01.0: Found an ISP2312, irq 185, iobase > > 0xf8812000 qla2300 0000:05:01.0: Configuring PCI space... > > qla2300 0000:05:01.0: Configure NVRAM parameters... > > qla2300 0000:05:01.0: Verifying loaded RISC code... > > qla2300 0000:05:01.0: Waiting for LIP to complete... > > > > until here all works fine, but then: > > > > input: PS/2 Generic Mouse on synaptcs-pt/serio0 qla2300 > > 0000:05:01.0: LIP reset occured (f7f7). > > qla2300 0000:05:01.0: LOOP UP detected (2 Gbps). > > qla2300 0000:05:01.0: Topology - (F_Port), Host Loop address 0xffff > > scsi3 : qla2xxx > > qla2300 0000:04:02.0: > > QLogic Fibre Channel HBA Driver: 8.01.00b5-k > > QLogic QLA2340 - 133MHz PCI-X to 2Gb FC, Single Channel > > ISP2312: PCI-X (100 MHz) @ 0000:05:01.0 hdma+, host#=3, > > fw=3.03.15 IPX > > Loading kernel/fs/reiserfs/reiserfs.ko > > Waiting for device /dev/sda4 to appear: .....not found --- > > exiting to /bin/sh $ > > > > if i use the standard (bigsmp) kernel the normal massages are: > > > > SCSI device sda: 41943040 512-byte hdwr sectors (21475 MB) > > SCSI device sda: drive cache: write back SCSI device sda: > > 41943040 512-byte hdwr sectors (21475 MB) SCSI device sda: > > drive cache: write back > > sda: sda1 sda2 sda3 sda4 > > ....usw. > > > > Well, my qla2300 has the storage attached not a generic mouse. > > Of course it isn't possible to boot from this mouse. :-( > > > > _______________________________________________ > Xen-users mailing list > Xen-users@lists.xensource.com > http://lists.xensource.com/xen-users