From: Ted Kaczmarek <tedkaz@optonline.net>
To: xen-devel@lists.xensource.com
Subject: changeset: 7473:94cee9a918de,
Date: Sat, 22 Oct 2005 17:18:29 -0400 [thread overview]
Message-ID: <1130015909.29641.28.camel@pluto.linsolutions.com> (raw)
Tyan 2462 SMP
Seeing issues with scsi errors and 3c59x driver again.
For kicks I tried modules and compiled into the kernel no difference.
I also saw this when 2.6.12-5 patch was applied corrrectly according to
changeset.
The only thing I can make of this is an irg sharing issue.
16: 887 0 Phys-irq aic7xxx, eth0
17: 4127 0 Phys-irq aic7xxx
16 is the same irq the scsi controller with all the timeout issues.
2.6.9-22.ELsmp - Centos 4.2 n
2.6.13-1.1532_FC4smp FC4
No issues with any of these, browsed over the changelogs for 2.6.13.4
and nothing relevant in their. Really don't see the point of spinning
a non zen 2.6.12.6 to test with unless someone here feels otherwise.
AE_NOT_FOUND
search_node c1195980 start_node c1195980 return_node 00000000
ACPI-1138: *** Error: Method execution failed
[\_SB_.PCI0.ISA_.SIO_.COM1._ST
A] (Node c1195980), AE_NOT_FOUND
ACPI-0352: *** Error: Looking up [Z00Q] in namespace, AE_NOT_FOUND
search_node c085f800 start_node c085f800 return_node 00000000
ACPI-1138: *** Error: Method execution failed
[\_SB_.PCI0.ISA_.SIO_.COM2._ST
A] (Node c085f800), AE_NOT_FOUND
ACPI-0352: *** Error: Looking up [Z00Q] in namespace, AE_NOT_FOUND
search_node c085f600 start_node c085f600 return_node 00000000
ACPI-1138: *** Error: Method execution failed
[\_SB_.PCI0.ISA_.SIO_.LPT_._ST
A] (Node c085f600), AE_NOT_FOUND
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
Boot video device is 0000:00:08.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP_._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 5 *10 11)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 5 10 11) *9
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 *5 10 11)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 5 10 *11)
ACPI-0352: *** Error: Looking up [Z00Q] in namespace, AE_NOT_FOUND
search_node c1195980 start_node c1195980 return_node 00000000
ACPI-1138: *** Error: Method execution failed
[\_SB_.PCI0.ISA_.SIO_.COM1._ST
A] (Node c1195980), AE_NOT_FOUND
ACPI-0352: *** Error: Looking up [Z00Q] in namespace, AE_NOT_FOUND
search_node c085f800 start_node c085f800 return_node 00000000
ACPI-1138: *** Error: Method execution failed
[\_SB_.PCI0.ISA_.SIO_.COM2._ST
A] (Node c085f800), AE_NOT_FOUND
ACPI-0352: *** Error: Looking up [Z00Q] in namespace, AE_NOT_FOUND
search_node c085f600 start_node c085f600 return_node 00000000
ACPI-1138: *** Error: Method execution failed
[\_SB_.PCI0.ISA_.SIO_.LPT_._ST
A] (Node c085f600), AE_NOT_FOUND
xen_mem: Initialising balloon driver.
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a
report
TC classifier action (bugs to netdev@vger.kernel.org cc hadi@cyberus.ca)
ACPI: PCI Interrupt 0000:00:0c.0[A] -> GSI 16 (level, low) -> IRQ 16
e1000: 0000:00:0c.0: e1000_reset: Hardware Error
e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connection
ACPI: PCI Interrupt 0000:00:0f.0[A] -> GSI 18 (level, low) -> IRQ 18
3c59x: Donald Becker and others. www.scyld.com/network/vortex.html
0000:00:0f.0: 3Com PCI 3c980C Python-T at 0x1c00. Vers LK1.1.19
***INVALID CHECKSUM 00db*** <3>*** EEPROM MAC address is invalid.
3c59x: vortex_probe1 fails. Returns -22
3c59x: probe of 0000:00:0f.0 failed with error -22
ACPI: PCI Interrupt 0000:00:10.0[A] -> GSI 19 (level, low) -> IRQ 19
0000:00:10.0: 3Com PCI 3c980C Python-T at 0x1c80. Vers LK1.1.19
***INVALID CHECKSUM 00df*** <3>*** EEPROM MAC address is invalid.
3c59x: vortex_probe1 fails. Returns -22
3c59x: probe of 0000:00:10.0 failed with error -22
ACPI: PCI Interrupt 0000:00:0d.0[A] -> GSI 16 (level, low) -> IRQ 16
ACPI: PCI Interrupt 0000:00:0d.1[B] -> GSI 17 (level, low) -> IRQ 17
scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.36
<Adaptec aic7899 Ultra160 SCSI adapter>
aic7899: Ultra160 Wide Channel A, SCSI Id=7, 32/253 SCBs
(scsi0:A:0:0): parity error detected in DT Data-in phase. SEQADDR(0x1a5)
SCSIRAT
E(0x0)
Unexpected non-DT Data Phase
scsi0:0:0:0: Attempting to queue an ABORT message
CDB: 0x12 0x0 0x0 0x0 0x24 0x0
scsi0: At time of recovery, card was not paused
>>>>>>>>>>>>>>>>>> Dump Card State Begins <<<<<<<<<<<<<<<<<
scsi0: Dumping Card State in Message-in phase, at SEQADDR 0x16b
Card was paused
ACCUM = 0x0, SINDEX = 0x81, DINDEX = 0x21, ARG_2 = 0xff
Regards,
Ted
reply other threads:[~2005-10-22 21:18 UTC|newest]
Thread overview: [no followups] expand[flat|nested] mbox.gz Atom feed
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1130015909.29641.28.camel@pluto.linsolutions.com \
--to=tedkaz@optonline.net \
--cc=xen-devel@lists.xensource.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.