From: Tejun Heo <htejun@gmail.com>
To: jgarzik@pobox.com, linux-ide@vger.kernel.org
Cc: Tejun Heo <htejun@gmail.com>
Subject: [PATCH 2/3] libata: convert assert(xxx)'s in low-level drivers to WARN_ON(!xxx)'s
Date: Sat, 11 Feb 2006 19:11:13 +0900 [thread overview]
Message-ID: <11396526732153-git-send-email-htejun@gmail.com> (raw)
In-Reply-To: <11396526734098-git-send-email-htejun@gmail.com>
This patch converts all assert(xxx)'s in low-level drivers to
WARN_ON(!xxx)'s. After this patch, there is no in-kernel user of the
libata assert() macro.
Signed-off-by: Tejun Heo <htejun@gmail.com>
---
drivers/scsi/ahci.c | 2 +-
drivers/scsi/sata_mv.c | 50 +++++++++++++++++++++++----------------------
drivers/scsi/sata_qstor.c | 4 ++--
drivers/scsi/sata_sx4.c | 2 +-
4 files changed, 29 insertions(+), 29 deletions(-)
5a00ebe55d888f3252e87798add5ae085bde4228
diff --git a/drivers/scsi/ahci.c b/drivers/scsi/ahci.c
index a65895f..12c76be 100644
--- a/drivers/scsi/ahci.c
+++ b/drivers/scsi/ahci.c
@@ -847,7 +847,7 @@ static inline int ahci_host_intr(struct
ci = readl(port_mmio + PORT_CMD_ISSUE);
if (likely((ci & 0x1) == 0)) {
if (qc) {
- assert(qc->err_mask == 0);
+ WARN_ON(qc->err_mask);
ata_qc_complete(qc);
qc = NULL;
}
diff --git a/drivers/scsi/sata_mv.c b/drivers/scsi/sata_mv.c
index 6c80527..732cb64 100644
--- a/drivers/scsi/sata_mv.c
+++ b/drivers/scsi/sata_mv.c
@@ -632,8 +632,8 @@ static void mv_irq_clear(struct ata_port
* @base: port base address
* @pp: port private data
*
- * Verify the local cache of the eDMA state is accurate with an
- * assert.
+ * Verify the local cache of the eDMA state is accurate with a
+ * WARN_ON.
*
* LOCKING:
* Inherited from caller.
@@ -644,15 +644,15 @@ static void mv_start_dma(void __iomem *b
writelfl(EDMA_EN, base + EDMA_CMD_OFS);
pp->pp_flags |= MV_PP_FLAG_EDMA_EN;
}
- assert(EDMA_EN & readl(base + EDMA_CMD_OFS));
+ WARN_ON(!(EDMA_EN & readl(base + EDMA_CMD_OFS)));
}
/**
* mv_stop_dma - Disable eDMA engine
* @ap: ATA channel to manipulate
*
- * Verify the local cache of the eDMA state is accurate with an
- * assert.
+ * Verify the local cache of the eDMA state is accurate with a
+ * WARN_ON.
*
* LOCKING:
* Inherited from caller.
@@ -670,7 +670,7 @@ static void mv_stop_dma(struct ata_port
writelfl(EDMA_DS, port_mmio + EDMA_CMD_OFS);
pp->pp_flags &= ~MV_PP_FLAG_EDMA_EN;
} else {
- assert(!(EDMA_EN & readl(port_mmio + EDMA_CMD_OFS)));
+ WARN_ON(EDMA_EN & readl(port_mmio + EDMA_CMD_OFS));
}
/* now properly wait for the eDMA to stop */
@@ -1061,15 +1061,15 @@ static void mv_qc_prep(struct ata_queued
return;
/* the req producer index should be the same as we remember it */
- assert(((readl(mv_ap_base(qc->ap) + EDMA_REQ_Q_IN_PTR_OFS) >>
- EDMA_REQ_Q_PTR_SHIFT) & MV_MAX_Q_DEPTH_MASK) ==
- pp->req_producer);
+ WARN_ON(((readl(mv_ap_base(qc->ap) + EDMA_REQ_Q_IN_PTR_OFS) >>
+ EDMA_REQ_Q_PTR_SHIFT) & MV_MAX_Q_DEPTH_MASK) !=
+ pp->req_producer);
/* Fill in command request block
*/
if (!(qc->tf.flags & ATA_TFLAG_WRITE))
flags |= CRQB_FLAG_READ;
- assert(MV_MAX_Q_DEPTH > qc->tag);
+ WARN_ON(MV_MAX_Q_DEPTH <= qc->tag);
flags |= qc->tag << CRQB_TAG_SHIFT;
pp->crqb[pp->req_producer].sg_addr =
@@ -1152,16 +1152,16 @@ static void mv_qc_prep_iie(struct ata_qu
return;
/* the req producer index should be the same as we remember it */
- assert(((readl(mv_ap_base(qc->ap) + EDMA_REQ_Q_IN_PTR_OFS) >>
- EDMA_REQ_Q_PTR_SHIFT) & MV_MAX_Q_DEPTH_MASK) ==
- pp->req_producer);
+ WARN_ON(((readl(mv_ap_base(qc->ap) + EDMA_REQ_Q_IN_PTR_OFS) >>
+ EDMA_REQ_Q_PTR_SHIFT) & MV_MAX_Q_DEPTH_MASK) !=
+ pp->req_producer);
/* Fill in Gen IIE command request block
*/
if (!(qc->tf.flags & ATA_TFLAG_WRITE))
flags |= CRQB_FLAG_READ;
- assert(MV_MAX_Q_DEPTH > qc->tag);
+ WARN_ON(MV_MAX_Q_DEPTH <= qc->tag);
flags |= qc->tag << CRQB_TAG_SHIFT;
crqb = (struct mv_crqb_iie *) &pp->crqb[pp->req_producer];
@@ -1226,12 +1226,12 @@ static unsigned int mv_qc_issue(struct a
in_ptr = readl(port_mmio + EDMA_REQ_Q_IN_PTR_OFS);
/* the req producer index should be the same as we remember it */
- assert(((in_ptr >> EDMA_REQ_Q_PTR_SHIFT) & MV_MAX_Q_DEPTH_MASK) ==
- pp->req_producer);
+ WARN_ON(((in_ptr >> EDMA_REQ_Q_PTR_SHIFT) & MV_MAX_Q_DEPTH_MASK) !=
+ pp->req_producer);
/* until we do queuing, the queue should be empty at this point */
- assert(((in_ptr >> EDMA_REQ_Q_PTR_SHIFT) & MV_MAX_Q_DEPTH_MASK) ==
- ((readl(port_mmio + EDMA_REQ_Q_OUT_PTR_OFS) >>
- EDMA_REQ_Q_PTR_SHIFT) & MV_MAX_Q_DEPTH_MASK));
+ WARN_ON(((in_ptr >> EDMA_REQ_Q_PTR_SHIFT) & MV_MAX_Q_DEPTH_MASK) !=
+ ((readl(port_mmio + EDMA_REQ_Q_OUT_PTR_OFS) >>
+ EDMA_REQ_Q_PTR_SHIFT) & MV_MAX_Q_DEPTH_MASK));
mv_inc_q_index(&pp->req_producer); /* now incr producer index */
@@ -1251,7 +1251,7 @@ static unsigned int mv_qc_issue(struct a
*
* This routine is for use when the port is in DMA mode, when it
* will be using the CRPB (command response block) method of
- * returning command completion information. We assert indices
+ * returning command completion information. We check indices
* are good, grab status, and bump the response consumer index to
* prove that we're up to date.
*
@@ -1267,16 +1267,16 @@ static u8 mv_get_crpb_status(struct ata_
out_ptr = readl(port_mmio + EDMA_RSP_Q_OUT_PTR_OFS);
/* the response consumer index should be the same as we remember it */
- assert(((out_ptr >> EDMA_RSP_Q_PTR_SHIFT) & MV_MAX_Q_DEPTH_MASK) ==
- pp->rsp_consumer);
+ WARN_ON(((out_ptr >> EDMA_RSP_Q_PTR_SHIFT) & MV_MAX_Q_DEPTH_MASK) !=
+ pp->rsp_consumer);
/* increment our consumer index... */
pp->rsp_consumer = mv_inc_q_index(&pp->rsp_consumer);
/* and, until we do NCQ, there should only be 1 CRPB waiting */
- assert(((readl(port_mmio + EDMA_RSP_Q_IN_PTR_OFS) >>
- EDMA_RSP_Q_PTR_SHIFT) & MV_MAX_Q_DEPTH_MASK) ==
- pp->rsp_consumer);
+ WARN_ON(((readl(port_mmio + EDMA_RSP_Q_IN_PTR_OFS) >>
+ EDMA_RSP_Q_PTR_SHIFT) & MV_MAX_Q_DEPTH_MASK) !=
+ pp->rsp_consumer);
/* write out our inc'd consumer index so EDMA knows we're caught up */
out_ptr &= EDMA_RSP_Q_BASE_LO_MASK;
diff --git a/drivers/scsi/sata_qstor.c b/drivers/scsi/sata_qstor.c
index 82c3df7..955131b 100644
--- a/drivers/scsi/sata_qstor.c
+++ b/drivers/scsi/sata_qstor.c
@@ -277,8 +277,8 @@ static unsigned int qs_fill_sg(struct at
unsigned int nelem;
u8 *prd = pp->pkt + QS_CPB_BYTES;
- assert(qc->__sg != NULL);
- assert(qc->n_elem > 0);
+ WARN_ON(qc->__sg == NULL);
+ WARN_ON(qc->n_elem == 0);
nelem = 0;
ata_for_each_sg(sg, qc) {
diff --git a/drivers/scsi/sata_sx4.c b/drivers/scsi/sata_sx4.c
index 212cff4..e158f7a 100644
--- a/drivers/scsi/sata_sx4.c
+++ b/drivers/scsi/sata_sx4.c
@@ -461,7 +461,7 @@ static void pdc20621_dma_prep(struct ata
unsigned int i, idx, total_len = 0, sgt_len;
u32 *buf = (u32 *) &pp->dimm_buf[PDC_DIMM_HEADER_SZ];
- assert(qc->flags & ATA_QCFLAG_DMAMAP);
+ WARN_ON(!(qc->flags & ATA_QCFLAG_DMAMAP));
VPRINTK("ata%u: ENTER\n", ap->id);
--
1.1.5
next prev parent reply other threads:[~2006-02-11 10:11 UTC|newest]
Thread overview: 5+ messages / expand[flat|nested] mbox.gz Atom feed top
2006-02-11 10:11 [PATCHSET] libata: kill assert Tejun Heo
2006-02-11 10:11 ` [PATCH 3/3] libata: kill assert() macro Tejun Heo
2006-02-11 10:11 ` Tejun Heo [this message]
2006-02-11 10:11 ` [PATCH 1/3] libata: convert assert(X)'s in libata core layer to WARN_ON(!X)'s Tejun Heo
2006-02-11 22:54 ` Jeff Garzik
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=11396526732153-git-send-email-htejun@gmail.com \
--to=htejun@gmail.com \
--cc=jgarzik@pobox.com \
--cc=linux-ide@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.