From: Jon Barnett <jbarnett@pobox.com>
To: BlueZ development <bluez-devel@lists.sourceforge.net>
Subject: Re: [Bluez-devel] Problems with Dell BCM2045 USB device
Date: Wed, 03 Jan 2007 15:04:21 -0500 [thread overview]
Message-ID: <1167854661.3145.4.camel@localhost> (raw)
In-Reply-To: <1167844461.20568.18.camel@violet>
[-- Attachment #1.1: Type: text/plain, Size: 11972 bytes --]
On Wed, 2007-01-03 at 18:14 +0100, Marcel Holtmann wrote:
> did you reload the driver or reboot your system? This would have been
> the first Broadcom chip where the values are correct. Can you
> check /sys/class/module/parameters/* that no quirk is actually active.
Oops, my bad! When I restored my original modprobe file it had my
initial force scofix quirk in it.
hci0: Type: USB
BD Address: 00:00:00:00:00:00 ACL MTU: 0:0 SCO MTU: 0:0
DOWN
RX bytes:0 acl:0 sco:0 events:0 errors:0
TX bytes:0 acl:0 sco:0 commands:0 errors:0
The session dump is:
device: hci0 snap_len: 1028 filter: 0xffffffff
< HCI Command: Create Connection (0x01|0x0005) plen 13
bdaddr 00:12:EE:E0:AB:CA ptype 0xcc18 rswitch 0x01 clkoffset 0x0000
Packet type: DM1 DM3 DM5 DH1 DH3 DH5
> HCI Event: Command Status (0x0f) plen 4
Create Connection (0x01|0x0005) status 0x00 ncmd 1
> HCI Event: Connect Complete (0x03) plen 11
status 0x00 handle 12 bdaddr 00:12:EE:E0:AB:CA type ACL encrypt 0x00
< ACL data: handle 12 flags 0x02 dlen 12
L2CAP(s): Connect req: psm 1 scid 0x0040
< HCI Command: Read Remote Supported Features (0x01|0x001b) plen 2
handle 12
> HCI Event: Command Status (0x0f) plen 4
Read Remote Supported Features (0x01|0x001b) status 0x00 ncmd 1
< HCI Command: Write Link Policy Settings (0x02|0x000d) plen 4
handle 12 policy 0x0f
Link policy: RSWITCH HOLD SNIFF PARK
> HCI Event: Read Remote Supported Features (0x0b) plen 11
status 0x00 handle 12
Features: 0xff 0xfd 0x29 0x78 0x18 0x18 0x00 0x80
> HCI Event: Command Complete (0x0e) plen 6
Write Link Policy Settings (0x02|0x000d) ncmd 1
status 0x00 handle 12
< HCI Command: Remote Name Request (0x01|0x0019) plen 10
bdaddr 00:12:EE:E0:AB:CA mode 2 clkoffset 0x0000
> HCI Event: Command Status (0x0f) plen 4
Remote Name Request (0x01|0x0019) status 0x00 ncmd 1
> HCI Event: Max Slots Change (0x1b) plen 3
handle 12 slots 5
> ACL data: handle 12 flags 0x02 dlen 16
L2CAP(s): Connect rsp: dcid 0x0051 scid 0x0040 result 0 status 0
Connection successful
< ACL data: handle 12 flags 0x02 dlen 12
L2CAP(s): Config req: dcid 0x0051 flags 0x00 clen 0
> ACL data: handle 12 flags 0x02 dlen 16
L2CAP(s): Config req: dcid 0x0040 flags 0x00 clen 4
MTU 100
< ACL data: handle 12 flags 0x02 dlen 18
L2CAP(s): Config rsp: scid 0x0051 flags 0x00 result 0 clen 4
Success
MTU 100
> HCI Event: Remote Name Req Complete (0x07) plen 255
status 0x00 bdaddr 00:12:EE:E0:AB:CA name 'HBH-610a'
> ACL data: handle 12 flags 0x02 dlen 14
L2CAP(s): Config rsp: scid 0x0040 flags 0x00 result 0 clen 0
Success
< ACL data: handle 12 flags 0x02 dlen 24
L2CAP(d): cid 0x0051 len 20 [psm 1]
SDP SSA Req: tid 0x0 len 0xf
pat uuid-16 0x1108 (Headset)
max 65535
aid(s) 0x0000 - 0xffff
cont 00
> HCI Event: Number of Completed Packets (0x13) plen 5
handle 12 packets 4
> ACL data: handle 12 flags 0x02 dlen 27
> ACL data: handle 12 flags 0x01 dlen 27
> ACL data: handle 12 flags 0x01 dlen 27
> ACL data: handle 12 flags 0x01 dlen 25
L2CAP(d): cid 0x0040 len 102 [psm 1]
SDP SSA Rsp: tid 0x0 len 0x61
count 94
record #0
aid 0x0000 (SrvRecHndl)
uint 0x10002
aid 0x0001 (SrvClassIDList)
< uuid-16 0x1108 (Headset) uuid-16 0x1203 (Audio) >
aid 0x0004 (ProtocolDescList)
< < uuid-16 0x0100 (L2CAP) > <
uuid-16 0x0003 (RFCOMM) uint 0x1 > >
aid 0x0009 (BTProfileDescList)
< < uuid-16 0x1108 (Headset) uint 0x100 > >
aid 0x0100 (SrvName)
str "SonyEricsson Headset Service"
aid 0x0302 (unknown)
bool 0x1
cont 00
< ACL data: handle 12 flags 0x02 dlen 12
L2CAP(s): Disconn req: dcid 0x0051 scid 0x0040
< HCI Command: Read Voice Setting (0x03|0x0025) plen 0
> HCI Event: Command Complete (0x0e) plen 6
Read Voice Setting (0x03|0x0025) ncmd 1
status 0x00 voice setting 0x0060
< ACL data: handle 12 flags 0x02 dlen 12
L2CAP(s): Connect req: psm 3 scid 0x0041
> ACL data: handle 12 flags 0x02 dlen 12
L2CAP(s): Disconn rsp: dcid 0x0051 scid 0x0040
> ACL data: handle 12 flags 0x02 dlen 16
L2CAP(s): Connect rsp: dcid 0x0052 scid 0x0041 result 1 status 1
Connection pending - Authentication pending
> HCI Event: Link Key Request (0x17) plen 6
bdaddr 00:12:EE:E0:AB:CA
< HCI Command: Link Key Request Reply (0x01|0x000b) plen 22
bdaddr 00:12:EE:E0:AB:CA key FDA84C7E01635351CE60FF683AEDE32F
> HCI Event: Command Complete (0x0e) plen 10
Link Key Request Reply (0x01|0x000b) ncmd 1
status 0x00 bdaddr 00:12:EE:E0:AB:CA
> ACL data: handle 12 flags 0x02 dlen 16
L2CAP(s): Connect rsp: dcid 0x0052 scid 0x0041 result 0 status 0
Connection successful
< ACL data: handle 12 flags 0x02 dlen 16
L2CAP(s): Config req: dcid 0x0052 flags 0x00 clen 4
MTU 1013
> ACL data: handle 12 flags 0x02 dlen 16
L2CAP(s): Config req: dcid 0x0041 flags 0x00 clen 4
MTU 56
< ACL data: handle 12 flags 0x02 dlen 18
L2CAP(s): Config rsp: scid 0x0052 flags 0x00 result 0 clen 4
Success
MTU 56
> HCI Event: Number of Completed Packets (0x13) plen 5
handle 12 packets 4
> ACL data: handle 12 flags 0x02 dlen 14
L2CAP(s): Config rsp: scid 0x0041 flags 0x00 result 0 clen 0
Success
< ACL data: handle 12 flags 0x02 dlen 8
L2CAP(d): cid 0x0052 len 4 [psm 3]
RFCOMM(s): SABM: cr 1 dlci 0 pf 1 ilen 0 fcs 0x1c
> ACL data: handle 12 flags 0x02 dlen 8
L2CAP(d): cid 0x0041 len 4 [psm 3]
RFCOMM(s): UA: cr 1 dlci 0 pf 1 ilen 0 fcs 0xd7
< ACL data: handle 12 flags 0x02 dlen 18
L2CAP(d): cid 0x0052 len 14 [psm 3]
RFCOMM(s): PN CMD: cr 1 dlci 0 pf 0 ilen 10 fcs 0x70 mcc_len 8
dlci 2 frame_type 0 credit_flow 15 pri 7 ack_timer 0
frame_size 51 max_retrans 0 credits 7
> ACL data: handle 12 flags 0x02 dlen 19
L2CAP(d): cid 0x0041 len 15 [psm 3]
RFCOMM(s): PN RSP: cr 0 dlci 0 pf 0 ilen 10 fcs 0xaa mcc_len 8
dlci 2 frame_type 0 credit_flow 14 pri 0 ack_timer 0
frame_size 50 max_retrans 0 credits 0
< ACL data: handle 12 flags 0x02 dlen 8
L2CAP(d): cid 0x0052 len 4 [psm 3]
RFCOMM(s): SABM: cr 1 dlci 2 pf 1 ilen 0 fcs 0x59
> ACL data: handle 12 flags 0x02 dlen 8
L2CAP(d): cid 0x0041 len 4 [psm 3]
RFCOMM(s): UA: cr 1 dlci 2 pf 1 ilen 0 fcs 0x92
< ACL data: handle 12 flags 0x02 dlen 12
L2CAP(d): cid 0x0052 len 8 [psm 3]
RFCOMM(s): MSC CMD: cr 1 dlci 0 pf 0 ilen 4 fcs 0x70 mcc_len 2
dlci 2 fc 0 rtc 1 rtr 1 ic 0 dv 1 b1 0 b2 0 b3 0 len 0
> ACL data: handle 12 flags 0x02 dlen 13
L2CAP(d): cid 0x0041 len 9 [psm 3]
RFCOMM(s): MSC CMD: cr 0 dlci 0 pf 0 ilen 4 fcs 0xaa mcc_len 2
dlci 2 fc 0 rtc 1 rtr 1 ic 0 dv 0 b1 0 b2 0 b3 0 len 0
< ACL data: handle 12 flags 0x02 dlen 12
L2CAP(d): cid 0x0052 len 8 [psm 3]
RFCOMM(s): MSC RSP: cr 1 dlci 0 pf 0 ilen 4 fcs 0x70 mcc_len 2
dlci 2 fc 0 rtc 1 rtr 1 ic 0 dv 0 b1 0 b2 0 b3 0 len 0
> HCI Event: Number of Completed Packets (0x13) plen 5
handle 12 packets 4
> ACL data: handle 12 flags 0x02 dlen 13
L2CAP(d): cid 0x0041 len 9 [psm 3]
RFCOMM(s): MSC RSP: cr 0 dlci 0 pf 0 ilen 4 fcs 0xaa mcc_len 2
dlci 2 fc 0 rtc 1 rtr 1 ic 0 dv 1 b1 0 b2 0 b3 0 len 0
< ACL data: handle 12 flags 0x02 dlen 9
L2CAP(d): cid 0x0052 len 5 [psm 3]
RFCOMM(d): UIH: cr 1 dlci 2 pf 1 ilen 0 fcs 0x86 credits 33
> ACL data: handle 12 flags 0x02 dlen 20
L2CAP(d): cid 0x0041 len 16 [psm 3]
RFCOMM(d): UIH: cr 0 dlci 2 pf 1 ilen 10 fcs 0x5c credits 20
0000: 41 54 2a 45 43 42 50 3d 3f 0d AT*ECBP=?.
< ACL data: handle 12 flags 0x02 dlen 14
L2CAP(d): cid 0x0052 len 10 [psm 3]
RFCOMM(d): UIH: cr 1 dlci 2 pf 0 ilen 6 fcs 0x9a
0000: 0d 0a 4f 4b 0d 0a ..OK..
> ACL data: handle 12 flags 0x02 dlen 19
L2CAP(d): cid 0x0041 len 15 [psm 3]
RFCOMM(d): UIH: cr 0 dlci 2 pf 0 ilen 10 fcs 0x40
0000: 41 54 2b 43 4c 49 50 3d 31 0d AT+CLIP=1.
< ACL data: handle 12 flags 0x02 dlen 14
L2CAP(d): cid 0x0052 len 10 [psm 3]
RFCOMM(d): UIH: cr 1 dlci 2 pf 0 ilen 6 fcs 0x9a
0000: 0d 0a 4f 4b 0d 0a ..OK..
> HCI Event: Number of Completed Packets (0x13) plen 5
handle 12 packets 4
> ACL data: handle 12 flags 0x02 dlen 26
L2CAP(d): cid 0x0041 len 22 [psm 3]
RFCOMM(d): UIH: cr 0 dlci 2 pf 1 ilen 16 fcs 0x5c credits 1
0000: 41 54 2b 43 53 43 53 3d 22 55 54 46 2d 38 22 0d AT
+CSCS="UTF-8".
< ACL data: handle 12 flags 0x02 dlen 14
L2CAP(d): cid 0x0052 len 10 [psm 3]
RFCOMM(d): UIH: cr 1 dlci 2 pf 0 ilen 6 fcs 0x9a
0000: 0d 0a 4f 4b 0d 0a ..OK..
> ACL data: handle 12 flags 0x02 dlen 27
> ACL data: handle 12 flags 0x01 dlen 5
L2CAP(d): cid 0x0041 len 28 [psm 3]
RFCOMM(d): UIH: cr 0 dlci 2 pf 1 ilen 22 fcs 0x5c credits 1
0000: 41 54 2a 53 45 41 4d 3d 22 48 42 48 2d 36 31 30
AT*SEAM="HBH-610
0010: 61 22 2c 31 33 0d a",13.
< ACL data: handle 12 flags 0x02 dlen 14
L2CAP(d): cid 0x0052 len 10 [psm 3]
RFCOMM(d): UIH: cr 1 dlci 2 pf 0 ilen 6 fcs 0x9a
0000: 0d 0a 4f 4b 0d 0a ..OK..
> ACL data: handle 12 flags 0x02 dlen 19
L2CAP(d): cid 0x0041 len 15 [psm 3]
RFCOMM(d): UIH: cr 0 dlci 2 pf 1 ilen 9 fcs 0x5c credits 1
0000: 41 54 2b 43 4c 41 4e 3f 0d AT+CLAN?.
< ACL data: handle 12 flags 0x02 dlen 14
L2CAP(d): cid 0x0052 len 10 [psm 3]
RFCOMM(d): UIH: cr 1 dlci 2 pf 0 ilen 6 fcs 0x9a
0000: 0d 0a 4f 4b 0d 0a ..OK..
> HCI Event: Number of Completed Packets (0x13) plen 5
handle 12 packets 3
> HCI Event: Max Slots Change (0x1b) plen 3
handle 12 slots 1
> HCI Event: Mode Change (0x14) plen 6
status 0x00 handle 12 mode 0x02 interval 2048
Mode: Sniff
< HCI Command: Add SCO Connection (0x01|0x0007) plen 4
handle 12 ptype 0x00e0
Packet type: HV1 HV2 HV3
> HCI Event: Command Status (0x0f) plen 4
Add SCO Connection (0x01|0x0007) status 0x00 ncmd 1
> HCI Event: Connect Complete (0x03) plen 11
status 0x00 handle 1 bdaddr 00:12:EE:E0:AB:CA type SCO encrypt 0x00
< HCI Command: Remote Name Request (0x01|0x0019) plen 10
bdaddr 00:12:EE:E0:AB:CA mode 2 clkoffset 0x0000
> HCI Event: Command Status (0x0f) plen 4
Remote Name Request (0x01|0x0019) status 0x00 ncmd 1
> HCI Event: Remote Name Req Complete (0x07) plen 255
status 0x00 bdaddr 00:12:EE:E0:AB:CA name 'HBH-610a'
> ACL data: handle 12 flags 0x02 dlen 19
L2CAP(d): cid 0x0041 len 15 [psm 3]
RFCOMM(d): UIH: cr 0 dlci 2 pf 1 ilen 9 fcs 0x5c credits 2
0000: 41 54 2b 56 47 53 3d 36 0d AT+VGS=6.
< ACL data: handle 12 flags 0x02 dlen 14
L2CAP(d): cid 0x0052 len 10 [psm 3]
RFCOMM(d): UIH: cr 1 dlci 2 pf 0 ilen 6 fcs 0x9a
0000: 0d 0a 4f 4b 0d 0a ..OK..
> HCI Event: Mode Change (0x14) plen 6
status 0x00 handle 12 mode 0x00 interval 0
Mode: Active
> HCI Event: Connection Packet Type Changed (0x1d) plen 5
status 0x00 handle 1 ptype 0x0080
Packet type: HV3
> HCI Event: Number of Completed Packets (0x13) plen 5
handle 12 packets 1
> HCI Event: Mode Change (0x14) plen 6
status 0x00 handle 12 mode 0x02 interval 2048
Mode: Sniff
Same end results with aplay hanging.
Cheers,
Jon.
[-- Attachment #1.2: This is a digitally signed message part --]
[-- Type: application/pgp-signature, Size: 189 bytes --]
[-- Attachment #2: Type: text/plain, Size: 347 bytes --]
-------------------------------------------------------------------------
Take Surveys. Earn Cash. Influence the Future of IT
Join SourceForge.net's Techsay panel and you'll get the chance to share your
opinions on IT & business topics through brief surveys - and earn cash
http://www.techsay.com/default.php?page=join.php&p=sourceforge&CID=DEVDEV
[-- Attachment #3: Type: text/plain, Size: 164 bytes --]
_______________________________________________
Bluez-devel mailing list
Bluez-devel@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/bluez-devel
next prev parent reply other threads:[~2007-01-03 20:04 UTC|newest]
Thread overview: 9+ messages / expand[flat|nested] mbox.gz Atom feed top
[not found] <mailman.341782.1167746753.8777.bluez-devel@lists.sourceforge.net>
2007-01-03 2:58 ` [Bluez-devel] Problems with Dell BCM2045 USB device Jon Barnett
2007-01-03 9:28 ` Marcel Holtmann
2007-01-03 17:05 ` Jon Barnett
2007-01-03 17:14 ` Marcel Holtmann
2007-01-03 20:04 ` Jon Barnett [this message]
2007-01-03 20:13 ` Marcel Holtmann
2007-01-03 21:56 ` Jon Barnett
2007-01-03 15:58 ` Brad Midgley
2007-01-08 20:14 ` Jon Barnett
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1167854661.3145.4.camel@localhost \
--to=jbarnett@pobox.com \
--cc=bluez-devel@lists.sourceforge.net \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.