Re: [Bluez-users] problem in parking device. bluez-libs 3.14, bluez-utils-3.14

[Marcel Holtmann <marcel@holtmann.org>]

Hi Mahin,

> I am trying to park one bluetooth device.
> 
> First of all i have tried to use the bluez hci.c function
> hci_park_mode() to park this device.
> I have used the function in following manner 
>       
>  
>        if( hci_park_mode(dd, handle, 0x200, 0x100, 25000) < 0 )
>       {
>          printf("\n Unable to park ...\n");
>       }
>        I am getting the handle correct here. 
> 
> These is the concerned part of code.. but I am not getting the device
> parked... 
> then I tried to check whether I can park it using hcitool cmd or not
> 
> This is the hciconfig -a output of my Master device
> 
> // Master 
> # hciconfig -a
> hci0:   Type: UART
>         BD Address: 00:80:37:2E:4C:C3 ACL MTU: 339:11 SCO MTU: 93:14
>         UP RUNNING PSCAN ISCAN
>         RX bytes:152425 acl:2402 sco:0 events:10389 errors:0
>         TX bytes:87079 acl:2791 sco:0 commands:3526 errors:0
>         Features: 0xff 0xff 0x8f 0xfe 0x9b 0xf9 0x00 0x80
>         Packet type: DM1 DM3 DM5 DH1 DH3 DH5 HV1 HV2 HV3
>         Link policy: RSWITCH HOLD SNIFF PARK
>         Link mode: SLAVE ACCEPT
>         Name: 'LB:[unknown]'
>         Class: 0x820116
>         Service Classes: Networking
>         Device Class: Computer, Palm
>         HCI Ver: 2.0 (0x3) HCI Rev: 0x62b9 LMP Ver: 2.0 (0x3) LMP
> Subver: 0x62b9
>         Manufacturer: Infineon Technologies AG (9)
> 
> Slave has the same configuration and its Link policy is also   Link
> policy: RSWITCH HOLD SNIFF PARK
> 
> These is the output of hcitool con
> # hcitool con
> Connections:
>         < ACL 11:11:11:11:11:11 handle 512 state 1 lm MASTER 
>         < ACL 00:80:37:2E:45:1E handle 256 state 1 lm MASTER 
> 
> # hcitool cmd 0x02 0x005 0x0200 0x0090 0x000E
> < HCI Command: ogf 0x02, ocf 0x0005, plen 3
>   00 90 0E
> > HCI Event: 0x0f plen 4
>   12 01 05 08
> 
> # hcitool cmd 0x02 0x005 0x0100 0x0090 0x000E
> < HCI Command: ogf 0x02, ocf 0x0005, plen 3
>   00 90 0E
> > HCI Event: 0x0f plen 4
>   12 01 05 08
> 
> By searching into mailing list archieve ( link :
> http://article.gmane.org/gmane.linux.bluez.devel/269/match=park )
> I came to know that may be my parameters are wrong but I am not able
> to understand what is wrong ..
> 
> One more thing.. hcitool con returns me handle as 256 ( hex 0x100 )..
> Now when I am giving this as first parameter in hcitool cmd the
> hex_dump function in 
> hcitool.c prints only last two digits i.e. 00 . .. so I am a bit
> confused that is my handle is passing correctly or not ?

the park mode support is always complicated. I would advise you to not
support it. Especially with non CSR based chips. However you have to run
hcidump -X -V to see what is really going on.

Regards

Marcel



-------------------------------------------------------------------------
This SF.net email is sponsored by: Splunk Inc.
Still grepping through log files to find problems?  Stop.
Now Search log events and configuration files using AJAX and a browser.
Download your FREE copy of Splunk now >>  http://get.splunk.com/
_______________________________________________
Bluez-users mailing list
Bluez-users@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/bluez-users