[PATCH v2] [POWERPC] Update MPC8610 HPCD to support audio drivers

[Timur Tabi <timur@freescale.com>]

Update the MPC8610 HPCD files to support the audio driver.  Update
booting-without-of.txt with information on the SSI device.

Signed-off-by: Timur Tabi <timur@freescale.com>
---

Updated based on comments from mailing lists.  Split the patch into two parts.

This patch applies on top of
git://git.kernel.org/pub/scm/linux/kernel/git/perex/alsa.git.

 Documentation/powerpc/booting-without-of.txt |   40 ++++++
 arch/powerpc/boot/dts/mpc8610_hpcd.dts       |  110 ++++++++++++++++-
 arch/powerpc/configs/mpc8610_hpcd_defconfig  |  171 +++++++++++++++++++++++++-
 arch/powerpc/platforms/86xx/mpc8610_hpcd.c   |   18 +++
 4 files changed, 335 insertions(+), 4 deletions(-)

diff --git a/Documentation/powerpc/booting-without-of.txt b/Documentation/powerpc/booting-without-of.txt
index e9a3cb1..826af91 100644
--- a/Documentation/powerpc/booting-without-of.txt
+++ b/Documentation/powerpc/booting-without-of.txt
@@ -53,6 +53,7 @@ Table of Contents
       j) CFI or JEDEC memory-mapped NOR flash
       k) Global Utilities Block
       l) Xilinx IP cores
+      p) Freescale Synchronous Serial Interface
 
   VII - Specifying interrupt information for devices
     1) interrupts property
@@ -2514,6 +2515,45 @@ platforms are moved over to use the flattened-device-tree model.
       Requred properties:
        - current-speed : Baud rate of uartlite
 
+    p) Freescale Synchronous Serial Interface
+
+       The SSI is a serial device that communicates with audio codecs.  It can
+       be programmed in AC97, I2S, left-justified, or right-justified modes.
+
+       Required properties:
+       - compatible	  : compatible list, containing "fsl,ssi"
+       - cell-index	  : the SSI, <0> = SSI1, <1> = SSI2, and so on
+       - reg		  : offset and length of the register set for the device
+       - interrupts	  : <a b> where a is the interrupt number and b is a
+                            field that represents an encoding of the sense and
+			    level information for the interrupt.  This should be
+			    encoded based on the information in section 2)
+			    depending on the type of interrupt controller you
+			    have.
+       - interrupt-parent : the phandle for the interrupt controller that
+                            services interrupts for this device.
+       - fsl,mode	  : the operating mode for the SSI interface
+			    "i2s-slave" - I2S mode, SSI is clock slave
+			    "i2s-master" - I2S mode, SSI is clock master
+			    "lj-slave" - left-justified mode, SSI is clock slave
+			    "lj-master" - l.j. mode, SSI is clock master
+			    "rj-slave" - right-justified mode, SSI is clock slave
+			    "rj-master" - r.j., SSI is clock master
+			    "ac97-slave" - AC97 mode, SSI is clock slave
+			    "ac97-master" - AC97 mode, SSI is clock master
+
+       Optional properties:
+       - codec		  : child node that defines an audio codec connected
+		 	    to this SSI
+
+       Child 'codec' node required properties:
+       - compatible	  : compatible list, contains the name of the codec
+
+       Child 'codec' node optional properties:
+       - bus-frequency	  : The frequency of the input clock, which typically
+                            comes from an on-board dedicated oscillator.
+
+
    More devices will be defined as this spec matures.
 
 VII - Specifying interrupt information for devices
diff --git a/arch/powerpc/boot/dts/mpc8610_hpcd.dts b/arch/powerpc/boot/dts/mpc8610_hpcd.dts
index 966edf1..fda0ace 100644
--- a/arch/powerpc/boot/dts/mpc8610_hpcd.dts
+++ b/arch/powerpc/boot/dts/mpc8610_hpcd.dts
@@ -1,7 +1,7 @@
 /*
  * MPC8610 HPCD Device Tree Source
  *
- * Copyright 2007 Freescale Semiconductor Inc.
+ * Copyright 2007-2008 Freescale Semiconductor Inc.
  *
  * This program is free software; you can redistribute  it and/or modify it
  * under the terms of the GNU General Public License Version 2 as published
@@ -42,6 +42,7 @@
 		#size-cells = <1>;
 		#interrupt-cells = <2>;
 		device_type = "soc";
+		compatible = "fsl,mpc8610";
 		ranges = <0 e0000000 00100000>;
 		reg = <e0000000 1000>;
 		bus-frequency = <0>;
@@ -103,6 +104,113 @@
 			reg = <e0000 1000>;
 			fsl,has-rstcr;
 		};
+
+		ssi@16000 {
+			compatible = "fsl,mpc8610-ssi";
+			cell-index = <0>;
+			reg = <16000 100>;
+			interrupt-parent = <&mpic>;
+			interrupts = <3e 2>;
+			fsl,mode = "i2s-slave";
+			codec {
+				compatible = "cirrus,cs4270";
+				/* MCLK source is a stand-alone oscillator */
+				clock-frequency = <bb8000>;
+			};
+		};
+
+		ssi@16100 {
+			compatible = "fsl,mpc8610-ssi";
+			cell-index = <1>;
+			reg = <16100 100>;
+			interrupt-parent = <&mpic>;
+			interrupts = <3f 2>;
+		};
+
+                dma@21300 {
+                        #address-cells = <1>;
+                        #size-cells = <1>;
+                        compatible = "fsl,mpc8610-dma", "fsl,eloplus-dma";
+                        cell-index = <0>;
+                        reg = <21300 4>; /* DMA general status register */
+                        ranges = <0 21100 200>;
+
+                        dma-channel@0 {
+				compatible = "fsl,mpc8610-dma-channel",
+					"fsl,eloplus-dma-channel";
+				cell-index = <0>;
+				reg = <0 80>;
+				interrupt-parent = <&mpic>;
+				interrupts = <14 2>;
+                        };
+                        dma-channel@1 {
+				compatible = "fsl,mpc8610-dma-channel",
+					"fsl,eloplus-dma-channel";
+				cell-index = <1>;
+				reg = <80 80>;
+				interrupt-parent = <&mpic>;
+				interrupts = <15 2>;
+                        };
+                        dma-channel@2 {
+				compatible = "fsl,mpc8610-dma-channel",
+					"fsl,eloplus-dma-channel";
+				cell-index = <2>;
+				reg = <100 80>;
+				interrupt-parent = <&mpic>;
+				interrupts = <16 2>;
+                        };
+                        dma-channel@3 {
+				compatible = "fsl,mpc8610-dma-channel",
+					"fsl,eloplus-dma-channel";
+				cell-index = <3>;
+				reg = <180 80>;
+				interrupt-parent = <&mpic>;
+				interrupts = <17 2>;
+                        };
+                };
+
+                dma@c300 {
+                        #address-cells = <1>;
+                        #size-cells = <1>;
+                        compatible = "fsl,mpc8610-dma", "fsl,mpc8540-dma";
+                        cell-index = <1>;
+                        reg = <c300 4>; /* DMA general status register */
+                        ranges = <0 c100 200>;
+
+                        dma-channel@0 {
+				compatible = "fsl,mpc8610-dma-channel",
+					"fsl,mpc8540-dma-channel";
+				cell-index = <0>;
+				reg = <0 80>;
+				interrupt-parent = <&mpic>;
+				interrupts = <3c 2>;
+                        };
+                        dma-channel@1 {
+				compatible = "fsl,mpc8610-dma-channel",
+					"fsl,mpc8540-dma-channel";
+				cell-index = <1>;
+				reg = <80 80>;
+				interrupt-parent = <&mpic>;
+				interrupts = <3d 2>;
+                        };
+                        dma-channel@2 {
+				compatible = "fsl,mpc8610-dma-channel",
+					"fsl,mpc8540-dma-channel";
+				cell-index = <2>;
+				reg = <100 80>;
+				interrupt-parent = <&mpic>;
+				interrupts = <3e 2>;
+                        };
+                        dma-channel@3 {
+				compatible = "fsl,mpc8610-dma-channel",
+					"fsl,mpc8540-dma-channel";
+				cell-index = <3>;
+				reg = <180 80>;
+				interrupt-parent = <&mpic>;
+				interrupts = <3f 2>;
+                        };
+                };
+
 	};
 
 	pci@e0008000 {
diff --git a/arch/powerpc/configs/mpc8610_hpcd_defconfig b/arch/powerpc/configs/mpc8610_hpcd_defconfig
index 0483211..fb68886 100644
--- a/arch/powerpc/configs/mpc8610_hpcd_defconfig
+++ b/arch/powerpc/configs/mpc8610_hpcd_defconfig
@@ -684,7 +684,7 @@ CONFIG_SERIAL_8250_RSA=y
 CONFIG_SERIAL_CORE=y
 CONFIG_SERIAL_CORE_CONSOLE=y
 # CONFIG_SERIAL_JSM is not set
-CONFIG_SERIAL_OF_PLATFORM=y
+# CONFIG_SERIAL_OF_PLATFORM is not set
 CONFIG_UNIX98_PTYS=y
 # CONFIG_LEGACY_PTYS is not set
 # CONFIG_IPMI_HANDLER is not set
@@ -699,7 +699,60 @@ CONFIG_UNIX98_PTYS=y
 # CONFIG_RAW_DRIVER is not set
 # CONFIG_TCG_TPM is not set
 CONFIG_DEVPORT=y
-# CONFIG_I2C is not set
+CONFIG_I2C=y
+CONFIG_I2C_BOARDINFO=y
+# CONFIG_I2C_CHARDEV is not set
+
+#
+# I2C Algorithms
+#
+# CONFIG_I2C_ALGOBIT is not set
+# CONFIG_I2C_ALGOPCF is not set
+# CONFIG_I2C_ALGOPCA is not set
+
+#
+# I2C Hardware Bus support
+#
+# CONFIG_I2C_ALI1535 is not set
+# CONFIG_I2C_ALI1563 is not set
+# CONFIG_I2C_ALI15X3 is not set
+# CONFIG_I2C_AMD756 is not set
+# CONFIG_I2C_AMD8111 is not set
+# CONFIG_I2C_I801 is not set
+# CONFIG_I2C_I810 is not set
+# CONFIG_I2C_PIIX4 is not set
+CONFIG_I2C_MPC=y
+# CONFIG_I2C_NFORCE2 is not set
+# CONFIG_I2C_OCORES is not set
+# CONFIG_I2C_PARPORT_LIGHT is not set
+# CONFIG_I2C_PROSAVAGE is not set
+# CONFIG_I2C_SAVAGE4 is not set
+# CONFIG_I2C_SIMTEC is not set
+# CONFIG_I2C_SIS5595 is not set
+# CONFIG_I2C_SIS630 is not set
+# CONFIG_I2C_SIS96X is not set
+# CONFIG_I2C_TAOS_EVM is not set
+# CONFIG_I2C_VIA is not set
+# CONFIG_I2C_VIAPRO is not set
+# CONFIG_I2C_VOODOO3 is not set
+
+#
+# Miscellaneous I2C Chip support
+#
+# CONFIG_SENSORS_DS1337 is not set
+# CONFIG_SENSORS_DS1374 is not set
+# CONFIG_DS1682 is not set
+# CONFIG_SENSORS_EEPROM is not set
+# CONFIG_SENSORS_PCF8574 is not set
+# CONFIG_SENSORS_PCA9539 is not set
+# CONFIG_SENSORS_PCF8591 is not set
+# CONFIG_SENSORS_M41T00 is not set
+# CONFIG_SENSORS_MAX6875 is not set
+# CONFIG_SENSORS_TSL2550 is not set
+# CONFIG_I2C_DEBUG_CORE is not set
+# CONFIG_I2C_DEBUG_ALGO is not set
+# CONFIG_I2C_DEBUG_BUS is not set
+# CONFIG_I2C_DEBUG_CHIP is not set
 
 #
 # SPI support
@@ -746,7 +799,119 @@ CONFIG_DUMMY_CONSOLE=y
 #
 # Sound
 #
-# CONFIG_SOUND is not set
+CONFIG_SOUND=y
+
+#
+# Advanced Linux Sound Architecture
+#
+CONFIG_SND=y
+CONFIG_SND_TIMER=y
+CONFIG_SND_PCM=y
+# CONFIG_SND_SEQUENCER is not set
+CONFIG_SND_OSSEMUL=y
+CONFIG_SND_MIXER_OSS=y
+CONFIG_SND_PCM_OSS=y
+# CONFIG_SND_PCM_OSS_PLUGINS is not set
+# CONFIG_SND_DYNAMIC_MINORS is not set
+# CONFIG_SND_SUPPORT_OLD_API is not set
+CONFIG_SND_VERBOSE_PROCFS=y
+# CONFIG_SND_VERBOSE_PRINTK is not set
+# CONFIG_SND_DEBUG is not set
+
+#
+# Generic devices
+#
+# CONFIG_SND_DUMMY is not set
+# CONFIG_SND_MTPAV is not set
+# CONFIG_SND_SERIAL_U16550 is not set
+# CONFIG_SND_MPU401 is not set
+
+#
+# PCI devices
+#
+# CONFIG_SND_AD1889 is not set
+# CONFIG_SND_ALS300 is not set
+# CONFIG_SND_ALS4000 is not set
+# CONFIG_SND_ALI5451 is not set
+# CONFIG_SND_ATIIXP is not set
+# CONFIG_SND_ATIIXP_MODEM is not set
+# CONFIG_SND_AU8810 is not set
+# CONFIG_SND_AU8820 is not set
+# CONFIG_SND_AU8830 is not set
+# CONFIG_SND_AZT3328 is not set
+# CONFIG_SND_BT87X is not set
+# CONFIG_SND_CA0106 is not set
+# CONFIG_SND_CMIPCI is not set
+# CONFIG_SND_CS4281 is not set
+# CONFIG_SND_CS46XX is not set
+# CONFIG_SND_CS5530 is not set
+# CONFIG_SND_DARLA20 is not set
+# CONFIG_SND_GINA20 is not set
+# CONFIG_SND_LAYLA20 is not set
+# CONFIG_SND_DARLA24 is not set
+# CONFIG_SND_GINA24 is not set
+# CONFIG_SND_LAYLA24 is not set
+# CONFIG_SND_MONA is not set
+# CONFIG_SND_MIA is not set
+# CONFIG_SND_ECHO3G is not set
+# CONFIG_SND_INDIGO is not set
+# CONFIG_SND_INDIGOIO is not set
+# CONFIG_SND_INDIGODJ is not set
+# CONFIG_SND_EMU10K1 is not set
+# CONFIG_SND_EMU10K1X is not set
+# CONFIG_SND_ENS1370 is not set
+# CONFIG_SND_ENS1371 is not set
+# CONFIG_SND_ES1938 is not set
+# CONFIG_SND_ES1968 is not set
+# CONFIG_SND_FM801 is not set
+# CONFIG_SND_HDA_INTEL is not set
+# CONFIG_SND_HDSP is not set
+# CONFIG_SND_HDSPM is not set
+# CONFIG_SND_ICE1712 is not set
+# CONFIG_SND_ICE1724 is not set
+# CONFIG_SND_INTEL8X0 is not set
+# CONFIG_SND_INTEL8X0M is not set
+# CONFIG_SND_KORG1212 is not set
+# CONFIG_SND_MAESTRO3 is not set
+# CONFIG_SND_MIXART is not set
+# CONFIG_SND_NM256 is not set
+# CONFIG_SND_PCXHR is not set
+# CONFIG_SND_RIPTIDE is not set
+# CONFIG_SND_RME32 is not set
+# CONFIG_SND_RME96 is not set
+# CONFIG_SND_RME9652 is not set
+# CONFIG_SND_SONICVIBES is not set
+# CONFIG_SND_TRIDENT is not set
+# CONFIG_SND_VIA82XX is not set
+# CONFIG_SND_VIA82XX_MODEM is not set
+# CONFIG_SND_VX222 is not set
+# CONFIG_SND_YMFPCI is not set
+
+#
+# ALSA PowerMac devices
+#
+
+#
+# ALSA PowerPC devices
+#
+
+#
+# System on Chip audio support
+#
+CONFIG_SND_SOC=y
+
+#
+# SoC Audio support for SuperH
+#
+
+#
+# ALSA SoC audio for Freescale SOCs
+#
+CONFIG_SND_SOC_MPC8610=y
+CONFIG_SND_SOC_MPC8610_HPCD=y
+CONFIG_SND_SOC_CS4270=y
+CONFIG_SND_SOC_CS4270_VD33_ERRATA=y
+
 CONFIG_HID_SUPPORT=y
 CONFIG_HID=y
 # CONFIG_HID_DEBUG is not set
diff --git a/arch/powerpc/platforms/86xx/mpc8610_hpcd.c b/arch/powerpc/platforms/86xx/mpc8610_hpcd.c
index 6390895..ed45a4a 100644
--- a/arch/powerpc/platforms/86xx/mpc8610_hpcd.c
+++ b/arch/powerpc/platforms/86xx/mpc8610_hpcd.c
@@ -34,9 +34,27 @@
 
 #include <asm/mpic.h>
 
+#include <linux/of_platform.h>
 #include <sysdev/fsl_pci.h>
 #include <sysdev/fsl_soc.h>
 
+static struct of_device_id mpc8610_ids[] = {
+	{ .compatible = "fsl,mpc8610", },
+	{}
+};
+
+static int __init mpc8610_declare_of_platform_devices(void)
+{
+	if (!machine_is(mpc86xx_hpcd))
+		return 0;
+
+	/* Without this call, the SSI device driver won't get probed. */
+	of_platform_bus_probe(NULL, mpc8610_ids, NULL);
+
+	return 0;
+}
+device_initcall(mpc8610_declare_of_platform_devices);
+
 void __init
 mpc86xx_hpcd_init_irq(void)
 {
-- 
1.5.2.4