From: "H. Willstrand" <h.willstrand@gmail.com>
To: "M. Istehbab" <hariskhan@gmail.com>
Cc: netdev@vger.kernel.org
Subject: Re: TCP connection failure in kernel 2.6.25
Date: Sat, 26 Apr 2008 12:18:56 +0200 [thread overview]
Message-ID: <1209205136.2929.6.camel@localhost.localdomain> (raw)
In-Reply-To: <c1410bfe0804260217t33139fd2v324af1a149843989@mail.gmail.com>
On Sat, 2008-04-26 at 14:17 +0500, M. Istehbab wrote:
> Package: linux-image-2.6.24-1-686
> Version: 2.6.24-6
> Severity: critical
>
> I have tried it with kernels from debian between 2.6.18-5-686 -
> 2.6.25. Be it vanilla versions/sources from kernel.org or debian built
> kernels. I have the same issue.
>
> The problem is random TCP connection failure for ipv4.
>
> I have seen a severe issue of this problem in my transparent proxy
> setup. This problem also occurs at times when it is not redirecting
> traffic, rather accepting it
> directly. Increasing the number of file descriptors didn't help. I
> rebuilt the kernel with 65K file descriptors, still the problem
> persists.
>
> Even if it is one client behind squid or this box, this happens. It
> will at random, not accept connections. squid doesn't report any in
> the log. netstat doesn't show any
> in its output as well.
>
Is the proxy server accepting connections after the issue has occurred?
Or do you need to re-boot? Or do you have to wait for a number of
seconds or what?
Cheers,
H. Willstrand
> I have changed NICs, I have changed between squid versions from 2.x to
> 3.x. Nothing has helped.
>
> Following are some settings to mention;
>
> ulimit -n is set to 8000
> net.core.somaxconn = 1024
> net.core.netdev_max_backlog = 3000
> net.ipv4.tcp_max_syn_backlog = 3000
>
> squid is built with 8000 file descriptors.
>
> This is a 60 client LAN behind this box, using it as an internet
> gateway/firewall for the following traffic;
>
> 1) vpn
> 2) email
> 3) cvs
> 4) browsing (http/https)
> 5) some ftp
>
> /////////////////////////////////////////////////////////////////////////////////////////
>
> This is a PIII (Coppermine)
> cpu MHz : 864.499
> RAM : 1 GB
> Hard disk : 2x 36 GB SCSI hard drives
> RAID : raid1
> Non Raid part : 3 non raid partitions
>
> /////////////////////////////////////////////////////////////////////////////////////////
>
> # cat /proc/mst
> cat: /proc/mst: No such file or directory
> sglhrcvs:~/work/traffic-shaping# cat /proc/mdstat
> Personalities : [raid1]
> md0 : active raid1 sda1[0] sdb1[1]
> 32226240 blocks [2/2] [UU]
>
>
> unused devices: <none>
>
> /////////////////////////////////////////////////////////////////////////////////////////
>
> This box worked fine when it had RHEL WS3 on it.
>
>
> -- Package-specific info:
> ** Version:
> Linux version 2.6.24-1-686 (Debian 2.6.24-6) (waldi@debian.org) (gcc
> version 4.1.3 20080308 (prerelease) (Debian 4.1.2-21)) #1 SMP Sat Apr
> 19 00:37:55 UTC 2008
>
> ** Command line:
> root=/dev/md0 ro
>
> process `sysctl' is using deprecated sysctl (syscall)
> net.ipv6.neigh.default.retrans_time; Use
> net.ipv6.neigh.default.retrans_time_ms instead.
>
> ** Loaded modules:
> Module Size Used by
> cls_u32 8100 1
> sch_cbq 16352 1
> tcp_diag 1792 0
> inet_diag 12136 1 tcp_diag
> xt_limit 2656 1
> xt_state 2464 1
> ipt_REDIRECT 2080 3
> ipt_MASQUERADE 3776 3
> xt_MARK 2272 11
> iptable_nat 6916 1
> nf_nat 18316 3 ipt_REDIRECT,ipt_MASQUERADE,iptable_nat
> nf_conntrack_ipv4 17352 3 iptable_nat
> nf_conntrack 62272 5
> xt_state,ipt_MASQUERADE,iptable_nat,nf_nat,nf_conntrack_ipv4
> iptable_filter 2976 1
> ppdev 8804 0
> lp 11076 0
> ac 6116 0
> battery 13572 0
> xt_TCPMSS 4384 1
> xt_tcpmss 2240 1
> xt_tcpudp 3136 29
> iptable_mangle 2784 1
> ip_tables 13188 3 iptable_nat,iptable_filter,iptable_mangle
> x_tables 14244 10
> xt_limit,xt_state,ipt_REDIRECT,ipt_MASQUERADE,xt_MARK,iptable_nat,xt_TCPMSS,xt_tcpmss,xt_tcpudp,ip_tables
> pppoe 12864 0
> pppox 3980 1 pppoe
> ppp_generic 26196 2 pppoe,pppox
> slhc 5920 1 ppp_generic
> ipv6 240836 35
> dm_snapshot 16964 0
> dm_mirror 21600 0
> dm_mod 55812 2 dm_snapshot,dm_mirror
> loop 16804 0
> parport_pc 33668 1
> parport 34280 3 ppdev,lp,parport_pc
> floppy 54628 0
> rtc 13052 0
> psmouse 36464 0
> pcspkr 3200 0
> i2c_i801 9232 0
> i2c_core 22432 1 i2c_i801
> button 8432 0
> serio_raw 6660 0
> shpchp 31028 0
> intel_agp 23412 1
> agpgart 31688 1 intel_agp
> pci_hotplug 27712 1 shpchp
> intel_rng 5632 0
> iTCO_wdt 11268 0
> evdev 11104 1
> sg 33264 0
> sr_mod 16708 0
> cdrom 32512 1 sr_mod
> ext3 122888 3
> jbd 43732 1 ext3
> mbcache 8288 1 ext3
> raid1 22240 1
> md_mod 73716 2 raid1
> ide_generic 1280 0 [permanent]
> sd_mod 27200 7
> aic7xxx 157560 5
> scsi_transport_spi 22816 1 aic7xxx
> ata_generic 7428 0
> libata 144464 1 ata_generic
> scsi_mod 141164 6
> sg,sr_mod,sd_mod,aic7xxx,scsi_transport_spi,libata
> generic 4388 0 [permanent]
> 3c59x 41064 0
> e100 33836 0
> mii 5312 2 3c59x,e100
> piix 7492 0 [permanent]
> uhci_hcd 23376 0
> ide_core 108292 3 ide_generic,generic,piix
> usbcore 132940 2 uhci_hcd
> thermal 16028 0
> processor 36520 1 thermal
> fan 4772 0
>
> ** PCI devices:
> 00:00.0 Host bridge [0600]: Intel Corporation 82840 840 (Carmel)
> Chipset Host Bridge (Hub A) [8086:1a21] (rev 01)
> Subsystem: Dell Unknown device [1028:0096]
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
> ParErr- Stepping- SERR+ FastB2B-
> Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
> <TAbort- <MAbort+ >SERR- <PERR+
> Latency: 0
> Region 0: Memory at ec000000 (32-bit, prefetchable) [size=32M]
> Capabilities: [a0] AGP version 2.0
> Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64-
> HTrans- 64bit- FW+ AGP3- Rate=x1,x2,x4
> Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit-
> FW- Rate=<none>
>
> 00:01.0 PCI bridge [0604]: Intel Corporation 82840 840 (Carmel)
> Chipset AGP Bridge [8086:1a23] (rev 01) (prog-if 00 [Normal decode])
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
> ParErr- Stepping- SERR+ FastB2B-
> Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Latency: 64
> Bus: primary=00, secondary=01, subordinate=01, sec-latency=64
> Memory behind bridge: f4000000-fbffffff
> Prefetchable memory behind bridge: 50000000-500fffff
> Secondary status: 66MHz+ FastB2B+ ParErr- DEVSEL=medium
> >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
> BridgeCtl: Parity- SERR+ NoISA+ VGA+ MAbort- >Reset- FastB2B-
>
> 00:1e.0 PCI bridge [0604]: Intel Corporation 82801AA PCI Bridge
> [8086:2418] (rev 02) (prog-if 00 [Normal decode])
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
> ParErr- Stepping- SERR+ FastB2B-
> Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Latency: 0
> Bus: primary=00, secondary=02, subordinate=03, sec-latency=64
> I/O behind bridge: 0000e000-0000ffff
> Memory behind bridge: f0000000-f3ffffff
> Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium
> >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
> BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
>
> 00:1f.0 ISA bridge [0601]: Intel Corporation 82801AA ISA Bridge (LPC)
> [8086:2410] (rev 02)
> Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop-
> ParErr- Stepping- SERR- FastB2B-
> Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium
> >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 0
>
> 00:1f.1 IDE interface [0101]: Intel Corporation 82801AA IDE
> [8086:2411] (rev 02) (prog-if 80 [Master])
> Subsystem: Intel Corporation 82801AA IDE [8086:2411]
> Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
> ParErr- Stepping- SERR- FastB2B-
> Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium
> >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Region 0: [virtual] Memory at 000001f0 (32-bit,
> non-prefetchable) [disabled] [size=8]
> Region 1: [virtual] Memory at 000003f0 (type 3,
> non-prefetchable) [disabled] [size=1]
> Region 2: [virtual] Memory at 00000170 (32-bit,
> non-prefetchable) [disabled] [size=8]
> Region 3: [virtual] Memory at 00000370 (type 3,
> non-prefetchable) [disabled] [size=1]
> Region 4: I/O ports at 1020 [size=16]
>
> 00:1f.2 USB Controller [0c03]: Intel Corporation 82801AA USB
> [8086:2412] (rev 02) (prog-if 00 [UHCI])
> Subsystem: Intel Corporation 82801AA USB [8086:2412]
> Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
> ParErr- Stepping- SERR- FastB2B-
> Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium
> >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 0
> Interrupt: pin D routed to IRQ 16
> Region 4: I/O ports at 1000 [size=32]
>
> 00:1f.3 SMBus [0c05]: Intel Corporation 82801AA SMBus [8086:2413] (rev 02)
> Subsystem: Intel Corporation 82801AA SMBus [8086:2413]
> Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
> ParErr- Stepping- SERR- FastB2B-
> Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium
> >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Interrupt: pin B routed to IRQ 18
> Region 4: I/O ports at dcd0 [size=16]
>
> 01:00.0 VGA compatible controller [0300]: S3 Inc. 86c368 [Trio 3D/2X]
> [5333:8a13] (rev 02) (prog-if 00 [VGA])
> Subsystem: S3 Inc. Trio3D/2X [5333:8a13]
> Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop-
> ParErr- Stepping- SERR- FastB2B-
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium
> >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Region 0: Memory at f4000000 (32-bit, non-prefetchable) [size=64M]
> Expansion ROM at 50000000 [disabled] [size=64K]
> Capabilities: [dc] Power Management version 1
> Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA
> PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
> Capabilities: [80] AGP version 1.0
> Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA- ITACoh- GART64-
> HTrans- 64bit- FW- AGP3- Rate=x1,x2
> Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=x2
>
> 02:04.0 Ethernet controller [0200]: 3Com Corporation 3c905C-TX/TX-M
> [Tornado] [10b7:9200] (rev 78)
> Subsystem: Dell Unknown device [1028:0096]
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop-
> ParErr- Stepping- SERR+ FastB2B-
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium
> >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 64 (2500ns min, 2500ns max), Cache Line Size: 32 bytes
> Interrupt: pin A routed to IRQ 17
> Region 0: I/O ports at ec80 [size=128]
> Region 1: Memory at f0fffc00 (32-bit, non-prefetchable) [size=128]
> Expansion ROM at f0200000 [disabled] [size=128K]
> Capabilities: [dc] Power Management version 2
> Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
> PME(D0+,D1+,D2+,D3hot+,D3cold+)
> Status: D0 PME-Enable- DSel=0 DScale=2 PME-
>
> 02:06.0 Multimedia audio controller [0401]: Cirrus Logic CS 4614/22/24
> [CrystalClear SoundFusion Audio Accelerator] [1013:6003] (rev 01)
> Subsystem: Dell Unknown device [1028:0096]
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
> ParErr- Stepping- SERR+ FastB2B-
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium
> >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 64 (1000ns min, 6000ns max)
> Interrupt: pin A routed to IRQ 9
> Region 0: Memory at f0ffe000 (32-bit, non-prefetchable) [size=4K]
> Region 1: Memory at f0e00000 (32-bit, non-prefetchable) [size=1M]
> Capabilities: [40] Power Management version 2
> Flags: PMEClk+ DSI+ D1+ D2+ AuxCurrent=0mA
> PME(D0+,D1+,D2+,D3hot+,D3cold-)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
> 02:08.0 Ethernet controller [0200]: Intel Corporation 82557/8/9
> [Ethernet Pro 100] [8086:1229] (rev 05)
> Subsystem: IBM 82558B Ethernet Pro 10/100 [1014:005c]
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop-
> ParErr- Stepping- SERR+ FastB2B-
> Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium
> >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 64 (2000ns min, 14000ns max), Cache Line Size: 32 bytes
> Interrupt: pin A routed to IRQ 17
> Region 0: Memory at ee000000 (32-bit, prefetchable) [size=4K]
> Region 1: I/O ports at ec60 [size=32]
> Region 2: Memory at f0d00000 (32-bit, non-prefetchable) [size=1M]
> Expansion ROM at f0000000 [disabled] [size=1M]
> Capabilities: [dc] Power Management version 1
> Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA
> PME(D0+,D1+,D2+,D3hot+,D3cold-)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
> 02:09.0 Ethernet controller [0200]: Intel Corporation 82557/8/9
> [Ethernet Pro 100] [8086:1229] (rev 0c)
> Subsystem: Intel Corporation EtherExpress PRO/100 S Desktop
> Adapter [8086:0040]
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop-
> ParErr- Stepping- SERR+ FastB2B-
> Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium
> >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 64 (2000ns min, 14000ns max), Cache Line Size: 32 bytes
> Interrupt: pin A routed to IRQ 18
> Region 0: Memory at f0ffd000 (32-bit, non-prefetchable) [size=4K]
> Region 1: I/O ports at ec00 [size=64]
> Region 2: Memory at f0fc0000 (32-bit, non-prefetchable) [size=128K]
> Expansion ROM at f0240000 [disabled] [size=64K]
> Capabilities: [dc] Power Management version 2
> Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA
> PME(D0+,D1+,D2+,D3hot+,D3cold+)
> Status: D0 PME-Enable- DSel=0 DScale=2 PME-
>
> 02:0b.0 Ethernet controller [0200]: 3Com Corporation 3c905B 100BaseTX
> [Cyclone] [10b7:9055] (rev 24)
> Subsystem: 3Com Corporation 3C905B Fast Etherlink XL 10/100 [10b7:9055]
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop-
> ParErr- Stepping- SERR+ FastB2B-
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium
> >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 64 (2500ns min, 2500ns max), Cache Line Size: 32 bytes
> Interrupt: pin A routed to IRQ 16
> Region 0: I/O ports at e880 [size=128]
> Region 1: Memory at f0fff800 (32-bit, non-prefetchable) [size=128]
> Expansion ROM at f0220000 [disabled] [size=128K]
> Capabilities: [dc] Power Management version 1
> Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
> PME(D0-,D1+,D2+,D3hot+,D3cold+)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
> 02:0e.0 PCI bridge [0604]: Digital Equipment Corporation DECchip 21152
> [1011:0024] (rev 03) (prog-if 00 [Normal decode])
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
> ParErr- Stepping- SERR+ FastB2B-
> Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium
> >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 64, Cache Line Size: 32 bytes
> Bus: primary=02, secondary=03, subordinate=03, sec-latency=64
> I/O behind bridge: 0000f000-0000ffff
> Memory behind bridge: f2000000-f3ffffff
> Prefetchable memory behind bridge: 00000000f0100000-00000000f01fffff
> Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium
> >TAbort- <TAbort- <MAbort- <SERR- <PERR-
> BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
> Capabilities: [dc] Power Management version 1
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=220mA
> PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
> Bridge: PM- B3+
>
> 03:0a.0 SCSI storage controller [0100]: Adaptec AIC-7899P U160/m
> [9005:00cf] (rev 01)
> Subsystem: Dell Unknown device [1028:0096]
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop-
> ParErr- Stepping- SERR+ FastB2B-
> Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium
> >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 64 (10000ns min, 6250ns max), Cache Line Size: 32 bytes
> Interrupt: pin A routed to IRQ 19
> BIST result: 00
> Region 0: I/O ports at fc00 [disabled] [size=256]
> Region 1: Memory at f2fff000 (64-bit, non-prefetchable) [size=4K]
> Expansion ROM at f3000000 [disabled] [size=128K]
> Capabilities: [dc] Power Management version 2
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
> PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
> 03:0a.1 SCSI storage controller [0100]: Adaptec AIC-7899P U160/m
> [9005:00cf] (rev 01)
> Subsystem: Dell Unknown device [1028:0096]
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop-
> ParErr- Stepping- SERR+ FastB2B-
> Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium
> >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 64 (10000ns min, 6250ns max), Cache Line Size: 32 bytes
> Interrupt: pin B routed to IRQ 16
> BIST result: 00
> Region 0: I/O ports at f800 [disabled] [size=256]
> Region 1: Memory at f2ffe000 (64-bit, non-prefetchable) [size=4K]
> Expansion ROM at f0100000 [disabled] [size=128K]
> Capabilities: [dc] Power Management version 2
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
> PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
>
>
> -- System Information:
> Debian Release: 4.0
> APT prefers stable
> APT policy: (500, 'stable')
> Architecture: i386 (i686)
> Shell: /bin/sh linked to /bin/bash
> Kernel: Linux 2.6.24-1-686
> Locale: LANG=en_US.UTF-8, LC_CTYPE=en_US.UTF-8 (charmap=UTF-8)
>
> Versions of packages linux-image-2.6.24-1-686 depends on:
> ii debconf [debconf-2.0] 1.5.11etch1 Debian configuration management sy
> ii initramfs-tools [linux-initr 0.85h tools for generating an initramfs
> ii module-init-tools 3.3-pre4-2 tools for managing Linux kernel mo
>
> Versions of packages linux-image-2.6.24-1-686 recommends:
> ii libc6-i686 2.3.6.ds1-13etch4 GNU C Library: Shared libraries [i
>
> -- debconf information:
> shared/kernel-image/really-run-bootloader: true
> linux-image-2.6.24-1-686/preinst/overwriting-modules-2.6.24-1-686: true
> linux-image-2.6.24-1-686/postinst/bootloader-error-2.6.24-1-686:
> linux-image-2.6.24-1-686/postinst/create-kimage-link-2.6.24-1-686: true
> linux-image-2.6.24-1-686/postinst/old-system-map-link-2.6.24-1-686: true
> linux-image-2.6.24-1-686/prerm/would-invalidate-boot-loader-2.6.24-1-686: true
> linux-image-2.6.24-1-686/preinst/initrd-2.6.24-1-686:
> linux-image-2.6.24-1-686/preinst/failed-to-move-modules-2.6.24-1-686:
> linux-image-2.6.24-1-686/postinst/depmod-error-initrd-2.6.24-1-686: false
> linux-image-2.6.24-1-686/preinst/bootloader-initrd-2.6.24-1-686: true
> linux-image-2.6.24-1-686/postinst/old-initrd-link-2.6.24-1-686: true
> linux-image-2.6.24-1-686/preinst/lilo-has-ramdisk:
> linux-image-2.6.24-1-686/postinst/old-dir-initrd-link-2.6.24-1-686: true
> linux-image-2.6.24-1-686/preinst/abort-install-2.6.24-1-686:
> linux-image-2.6.24-1-686/prerm/removing-running-kernel-2.6.24-1-686: true
> linux-image-2.6.24-1-686/postinst/depmod-error-2.6.24-1-686: false
> linux-image-2.6.24-1-686/preinst/abort-overwrite-2.6.24-1-686:
> linux-image-2.6.24-1-686/preinst/elilo-initrd-2.6.24-1-686: true
> linux-image-2.6.24-1-686/postinst/bootloader-test-error-2.6.24-1-686:
> linux-image-2.6.24-1-686/postinst/kimage-is-a-directory:
> linux-image-2.6.24-1-686/preinst/lilo-initrd-2.6.24-1-686: true
> --
> To unsubscribe from this list: send the line "unsubscribe netdev" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html
next prev parent reply other threads:[~2008-04-26 10:24 UTC|newest]
Thread overview: 7+ messages / expand[flat|nested] mbox.gz Atom feed top
2008-04-26 9:17 TCP connection failure in kernel 2.6.25 M. Istehbab
2008-04-26 10:18 ` H. Willstrand [this message]
2008-04-26 12:16 ` M. Istehbab
2008-04-26 20:27 ` H. Willstrand
2008-04-27 6:02 ` M. Istehbab
2008-04-27 16:56 ` H. Willstrand
2008-05-08 19:32 ` M. Istehbab
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1209205136.2929.6.camel@localhost.localdomain \
--to=h.willstrand@gmail.com \
--cc=hariskhan@gmail.com \
--cc=netdev@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.