From: Stelian Pop <stelian@popies.net>
To: u-boot@lists.denx.de
Subject: [U-Boot] [patch 0/3] Improve stability USB memory sticks for the common OHCI USB layer.
Date: Thu, 02 Oct 2008 17:51:47 +0200 [thread overview]
Message-ID: <1222962707.978.3.camel@galileo> (raw)
In-Reply-To: <1221941681.6646.8.camel@galileo>
Hi Remy,
Sorry it took so long but here are the results of the tests on my
AT91SAM9261-EK.
Le samedi 20 septembre 2008 ? 22:14 +0200, Stelian Pop a ?crit :
> > Also, it would be very helpful if you would test your sticks on a
> > SAM9261, because that SoC _must_ work. (I tested on AT91SAM9261-EK,
> > and custom board)
> > Then we can relate the problem to a specific USB stick, or to a
> certain SoC.
>
> Hmm, I can do that, but not before September 29.
The stick is fine, it does work ok on the 9261:
usb reset
(Re)start USB...
USB: scanning bus for devices... New Device 0
usb_control_msg: request: 0x6, requesttype: 0x80, value 0x100 index 0x0 length 0x40
usb_control_msg: request: 0x6, requesttype: 0x80, value 0x100 index 0x0 length 0x40
usb_control_msg: request: 0x6, requesttype: 0x80, value 0x100 index 0x0 length 0x40
set address 1
usb_control_msg: request: 0x5, requesttype: 0x0, value 0x1 index 0x0 length 0x0
usb_control_msg: request: 0x6, requesttype: 0x80, value 0x100 index 0x0 length 0x12
usb_control_msg: request: 0x6, requesttype: 0x80, value 0x200 index 0x0 length 0x8
usb_control_msg: request: 0x6, requesttype: 0x80, value 0x200 index 0x0 length 0x19
get_conf_no 0 Result 25, wLength 25
if 0, ep 0
##EP epmaxpacketin[1] = 2
set configuration 1
usb_control_msg: request: 0x9, requesttype: 0x0, value 0x1 index 0x0 length 0x0
new device strings: Mfr=0, Product=1, SerialNumber=0
usb_control_msg: request: 0x6, requesttype: 0x80, value 0x300 index 0x0 length 0xFF
USB device number 1 default language ID 0x409
usb_control_msg: request: 0x6, requesttype: 0x80, value 0x301 index 0x409 length 0xFF
Manufacturer
Product OHCI Root Hub
SerialNumber
usb_control_msg: request: 0x6, requesttype: 0xA0, value 0x2900 index 0x0 length 0x4
usb_control_msg: request: 0x6, requesttype: 0xA0, value 0x2900 index 0x0 length 0x9
usb_control_msg: request: 0x0, requesttype: 0xA0, value 0x0 index 0x0 length 0x4
usb_control_msg: request: 0x3, requesttype: 0x23, value 0x8 index 0x1 length 0x0
usb_control_msg: request: 0x3, requesttype: 0x23, value 0x8 index 0x2 length 0x0
usb_control_msg: request: 0x0, requesttype: 0xA3, value 0x0 index 0x1 length 0x4
usb_control_msg: request: 0x0, requesttype: 0xA3, value 0x0 index 0x1 length 0x4
usb_control_msg: request: 0x1, requesttype: 0x23, value 0x10 index 0x1 length 0x0
usb_control_msg: request: 0x3, requesttype: 0x23, value 0x4 index 0x1 length 0x0
usb_control_msg: request: 0x0, requesttype: 0xA3, value 0x0 index 0x1 length 0x4
usb_control_msg: request: 0x1, requesttype: 0x23, value 0x14 index 0x1 length 0x0
New Device 1
usb_control_msg: request: 0x6, requesttype: 0x80, value 0x100 index 0x0 length 0x40
usb_control_msg: request: 0x6, requesttype: 0x80, value 0x100 index 0x0 length 0x40
usb_control_msg: request: 0x6, requesttype: 0x80, value 0x100 index 0x0 length 0x40
usb_control_msg: request: 0x3, requesttype: 0x23, value 0x4 index 0x1 length 0x0
usb_control_msg: request: 0x0, requesttype: 0xA3, value 0x0 index 0x1 length 0x4
usb_control_msg: request: 0x1, requesttype: 0x23, value 0x14 index 0x1 length 0x0
set address 2
usb_control_msg: request: 0x5, requesttype: 0x0, value 0x2 index 0x0 length 0x0
usb_control_msg: request: 0x6, requesttype: 0x80, value 0x100 index 0x0 length 0x12
usb_control_msg: request: 0x6, requesttype: 0x80, value 0x200 index 0x0 length 0x8
usb_control_msg: request: 0x6, requesttype: 0x80, value 0x200 index 0x0 length 0x27
get_conf_no 0 Result 39, wLength 39
if 0, ep 0
if 0, ep 1
if 0, ep 2
##EP epmaxpacketout[1] = 64
##EP epmaxpacketin[2] = 64
##EP epmaxpacketin[3] = 64
set configuration 1
usb_control_msg: request: 0x9, requesttype: 0x0, value 0x1 index 0x0 length 0x0
new device strings: Mfr=1, Product=2, SerialNumber=3
usb_control_msg: request: 0x6, requesttype: 0x80, value 0x300 index 0x0 length 0xFF
USB device number 2 default language ID 0x409
usb_control_msg: request: 0x6, requesttype: 0x80, value 0x301 index 0x409 length 0xFF
usb_control_msg: request: 0x6, requesttype: 0x80, value 0x302 index 0x409 length 0xFF
usb_control_msg: request: 0x6, requesttype: 0x80, value 0x303 index 0x409 length 0xFF
Manufacturer P Technology
Product USB Mass Storage Device
SerialNumber 00000000000722
usb_control_msg: request: 0x0, requesttype: 0xA3, value 0x0 index 0x2 length 0x4
2 USB Device(s) found
scanning bus for storage devices... usb_control_msg: request: 0xFF, requesttype: 0x21, value 0x0 index 0x0 length 0x0
usb_control_msg: request: 0x1, requesttype: 0x2, value 0x0 index 0x82 length 0x0
usb_control_msg: request: 0x1, requesttype: 0x2, value 0x0 index 0x1 length 0x0
1 Storage Device(s) found
U-Boot> usb storage
Device 0: Vendor: UT163 Rev: 0.00 Prod: USB Flash Disk
Type: Removable Hard Disk
Capacity: 963.9 MB = 0.9 GB (1974271 x 512)
U-Boot>
U-Boot> fatls usb 0 1
.
51878326 download.tgz
20351 tp.tgz
2 file(s), 0 dir(s)
U-Boot>
--
Stelian Pop <stelian@popies.net>
next prev parent reply other threads:[~2008-10-02 15:51 UTC|newest]
Thread overview: 22+ messages / expand[flat|nested] mbox.gz Atom feed top
2008-09-16 12:55 [U-Boot] [patch 0/3] Improve stability USB memory sticks for the common OHCI USB layer Remy Bohmer
2008-09-16 12:55 ` [U-Boot] [patch 1/3] Fix for USB sticks not working on ARM while using GCC 4.x compilers Remy Bohmer
2008-09-16 12:55 ` [U-Boot] [patch 2/3] Refactoring parts of the common USB OHCI code Remy Bohmer
2008-09-16 12:55 ` [U-Boot] [patch 3/3] USB layer of U-Boot causes USB protocol errors while using USB memory sticks Remy Bohmer
2008-09-16 14:10 ` [U-Boot] [patch 0/3] Improve stability USB memory sticks for the common OHCI USB layer Markus Klotzbücher
2008-09-17 3:09 ` [U-Boot] [patch 0/3] Improve stability USB memory sticks for the commonOHCI " Thao To Hieu
2008-09-17 20:31 ` [U-Boot] [patch 0/3] Improve stability USB memory sticks for the common OHCI " Markus Klotzbücher
2008-09-18 12:00 ` Stelian Pop
2008-09-18 14:54 ` Remy Bohmer
2008-09-19 8:46 ` Stelian Pop
2008-09-19 9:16 ` Remy Bohmer
2008-09-19 14:42 ` Stelian Pop
2008-09-20 9:38 ` Remy Bohmer
2008-09-20 20:14 ` Stelian Pop
2008-10-02 15:51 ` Stelian Pop [this message]
2008-10-02 18:45 ` Remy Bohmer
2008-09-21 18:24 ` Wolfgang Denk
2008-09-22 8:26 ` Remy Bohmer
2008-09-19 9:45 ` Remy Bohmer
2008-09-19 10:05 ` Markus Klotzbücher
2008-09-19 10:19 ` Remy Bohmer
2008-09-18 15:01 ` Remy Bohmer
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1222962707.978.3.camel@galileo \
--to=stelian@popies.net \
--cc=u-boot@lists.denx.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.