From: Ben Hutchings <bhutchings@solarflare.com>
To: David Miller <davem@davemloft.net>
Cc: netdev@vger.kernel.org, linux-net-drivers@solarflare.com
Subject: [PATCH 00/20] sfc: Fixes and new PHY support for 2.6.29
Date: Thu, 29 Jan 2009 19:12:38 +0000 [thread overview]
Message-ID: <1233256358.3656.9.camel@achroite> (raw)
Please take the following changes for 2.6.29.
The changes are made up of:
- Bug fixes based on internal QA for version 2.3
- Addition of one new PHY and board
- A small feature addition for the SFT9001 (which is itself new for .29)
Ben.
Ben Hutchings (14):
sfc: SFT9001: Include non-breaking cable diagnostics in online
self-tests
sfc: Fix test for MDIO read failure
sfc: SFT9001/SFN4111T: Check PHY boot status during board
initialisation
sfc: SFN4111T: Fix GPIO sharing between I2C and FLASH_CFG_1
sfc: Update board info for hardware monitor on SFN4111T-R5 and later
sfc: SFT9001: Always enable XNP exchange on SFT9001 rev B
sfc: SFX7101/SFT9001: Fix AN advertisements
sfc: Remove "XFP" from log messages that are not specific to XFP
sfc: Fix reporting of PHY id
sfc: Add support for QT2025C PHY
sfc: Delete unused efx_blinker::led_num field
sfc: Clean up LED control
sfc: Add support for SFN4112F SFP+ reference design
sfc: Replace stats_enabled flag with a disable count
Steve Hodgson (6):
sfc: SFT9001: Enable robust link training
sfc: SFX7101: Remove workaround for bad link training
sfc: SFT9001: Fix speed reporting in 1G PHY loopback
sfc: Fix post-reset MAC selection
sfc: Reinitialise the PHY completely in case of a PHY or NIC reset
sfc: Test for PHYXS faults whenever we cannot test link state bits
--
Ben Hutchings, Senior Software Engineer, Solarflare Communications
Not speaking for my employer; that's the marketing department's job.
They asked us to note that Solarflare product names are trademarked.
next reply other threads:[~2009-01-29 19:12 UTC|newest]
Thread overview: 40+ messages / expand[flat|nested] mbox.gz Atom feed top
2009-01-29 19:12 Ben Hutchings [this message]
2009-01-29 19:15 ` [PATCH 01/20] sfc: SFT9001: Include non-breaking cable diagnostics in online self-tests Ben Hutchings
2009-01-29 19:16 ` [PATCH 02/20] sfc: Fix test for MDIO read failure Ben Hutchings
2009-01-29 19:17 ` [PATCH 03/20] sfc: SFT9001: Enable robust link training Ben Hutchings
2009-01-29 19:23 ` Ben Hutchings
2009-01-29 19:17 ` [PATCH 04/20] sfc: SFX7101: Remove workaround for bad " Ben Hutchings
2009-01-29 19:23 ` Ben Hutchings
2009-01-29 19:17 ` [PATCH 05/20] sfc: SFT9001/SFN4111T: Check PHY boot status during board initialisation Ben Hutchings
2009-01-29 19:17 ` [PATCH 06/20] sfc: SFT9001: Fix speed reporting in 1G PHY loopback Ben Hutchings
2009-01-29 19:18 ` [PATCH 07/20] sfc: SFN4111T: Fix GPIO sharing between I2C and FLASH_CFG_1 Ben Hutchings
2009-01-29 19:19 ` [PATCH 08/20] sfc: Fix post-reset MAC selection Ben Hutchings
2009-01-29 19:19 ` [PATCH 09/20] sfc: Reinitialise the PHY completely in case of a PHY or NIC reset Ben Hutchings
2009-01-29 19:19 ` [PATCH 10/20] sfc: Test for PHYXS faults whenever we cannot test link state bits Ben Hutchings
2009-01-29 19:19 ` [PATCH 11/20] sfc: Update board info for hardware monitor on SFN4111T-R5 and later Ben Hutchings
2009-01-29 19:20 ` [PATCH 12/20] sfc: SFT9001: Always enable XNP exchange on SFT9001 rev B Ben Hutchings
2009-01-29 19:20 ` [PATCH 13/20] sfc: SFX7101/SFT9001: Fix AN advertisements Ben Hutchings
2009-01-29 19:20 ` [PATCH 14/20] sfc: Remove "XFP" from log messages that are not specific to XFP Ben Hutchings
2009-01-29 19:20 ` [PATCH 15/20] sfc: Fix reporting of PHY id Ben Hutchings
2009-01-29 19:21 ` [PATCH 16/20] sfc: Add support for QT2025C PHY Ben Hutchings
2009-01-29 19:21 ` [PATCH 17/20] sfc: Delete unused efx_blinker::led_num field Ben Hutchings
2009-01-29 19:21 ` [PATCH 18/20] sfc: Clean up LED control Ben Hutchings
2009-01-29 19:21 ` [PATCH 19/20] sfc: Add support for SFN4112F SFP+ reference design Ben Hutchings
2009-01-29 19:22 ` [PATCH 20/20] sfc: Replace stats_enabled flag with a disable count Ben Hutchings
2009-01-29 23:26 ` [PATCH 00/20] sfc: Fixes and new PHY support for 2.6.29 David Miller
2009-01-30 1:05 ` Ben Hutchings
2009-01-30 1:08 ` David Miller
2009-01-30 3:48 ` [PATCH 01/11] sfc: SFT9001: Enable robust link training Ben Hutchings
2009-01-30 22:09 ` David Miller
2009-01-31 0:04 ` Ben Hutchings
2009-01-31 0:02 ` David Miller
2009-01-30 3:48 ` [PATCH 02/11] sfc: SFX7101: Remove workaround for bad " Ben Hutchings
2009-01-30 3:49 ` [PATCH 03/11] sfc: SFT9001: Fix speed reporting in 1G PHY loopback Ben Hutchings
2009-01-30 3:49 ` [PATCH 04/11] sfc: SFN4111T: Fix GPIO sharing between I2C and FLASH_CFG_1 Ben Hutchings
2009-01-30 3:49 ` [PATCH 05/11] sfc: Fix post-reset MAC selection Ben Hutchings
2009-01-30 3:50 ` [PATCH 06/11] sfc: Reinitialise the PHY completely in case of a PHY or NIC reset Ben Hutchings
2009-01-30 3:51 ` [PATCH 07/11] sfc: Test for PHYXS faults whenever we cannot test link state bits Ben Hutchings
2009-01-30 3:51 ` [PATCH 08/11] sfc: Update board info for hardware monitor on SFN4111T-R5 and later Ben Hutchings
2009-01-30 3:52 ` [PATCH 09/11] sfc: SFT9001: Always enable XNP exchange on SFT9001 rev B Ben Hutchings
2009-01-30 3:59 ` [PATCH 10/11] sfc: SFX7101/SFT9001: Fix AN advertisements Ben Hutchings
2009-01-30 4:00 ` [PATCH 11/11] sfc: Replace stats_enabled flag with a disable count Ben Hutchings
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1233256358.3656.9.camel@achroite \
--to=bhutchings@solarflare.com \
--cc=davem@davemloft.net \
--cc=linux-net-drivers@solarflare.com \
--cc=netdev@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.