From: Andrew Reay <certain@tpg.com.au>
To: linux-media@vger.kernel.org
Subject: Compro T750F - frontend initialization failing
Date: Sat, 14 Mar 2009 15:14:18 +1000 [thread overview]
Message-ID: <1237007658.19797.0.camel@desktop> (raw)
In-Reply-To: <49B982A5.7010103@august.de>
Hi Everyone,
I'm having trouble with getting the Compro Video T750F to work under
Ubuntu 8.10. I had the Compro T300 working great but this card is still
eluding me.
Any suggestions on how to proceed from here?
The dmesg is posted below.
Thanks,
Andrew
[ 13.317113] saa7130/34: v4l2 driver version 0.2.14 loaded
[ 13.317703] ACPI: PCI Interrupt Link [APC1] enabled at IRQ 16
[ 13.317709] saa7134 0000:04:08.0: PCI INT A -> Link[APC1] -> GSI 16
(level, low) -> IRQ 16
[ 13.317716] saa7133[0]: found at 0000:04:08.0, rev: 209, irq: 16,
latency: 32, mmio: 0xfdbfe000
[ 13.317723] saa7133[0]: subsystem: 185b:c900, board: Compro VideoMate
T750 [card=139,autodetected]
[ 13.317734] saa7133[0]: board init: gpio is 84bf00
[ 13.317746] saa7133[0]: Oops: IR config error [card=139]
[ 13.476035] saa7133[0]: i2c eeprom 00: 5b 18 00 c9 54 20 1c 00 43 43 a9
1c 55 d2 b2 92
[ 13.476046] saa7133[0]: i2c eeprom 10: 00 ff 86 0f ff 20 ff ff ff ff ff
ff ff ff ff ff
[ 13.476055] saa7133[0]: i2c eeprom 20: 01 40 01 02 02 01 03 01 08 ff 00
87 ff ff ff ff
[ 13.476064] saa7133[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff
ff ff ff ff ff
[ 13.476072] saa7133[0]: i2c eeprom 40: ff d7 00 c4 86 1e 05 ff 02 c2 ff
01 c6 ff 05 ff
[ 13.476081] saa7133[0]: i2c eeprom 50: ff ff ff ff ff ff ff ff ff ff ff
ff ff ff ff cb
[ 13.476089] saa7133[0]: i2c eeprom 60: 35 ff ff ff ff ff ff ff ff ff ff
ff ff ff ff ff
[ 13.476098] saa7133[0]: i2c eeprom 70: ff ff ff ff ff ff ff ff ff ff ff
ff ff ff ff ff
[ 13.476106] saa7133[0]: i2c eeprom 80: ff ff ff ff ff ff ff ff ff ff ff
ff ff ff ff ff
[ 13.476115] saa7133[0]: i2c eeprom 90: ff ff ff ff ff ff ff ff ff ff ff
ff ff ff ff ff
[ 13.476123] saa7133[0]: i2c eeprom a0: ff ff ff ff ff ff ff ff ff ff ff
ff ff ff ff ff
[ 13.476132] saa7133[0]: i2c eeprom b0: ff ff ff ff ff ff ff ff ff ff ff
ff ff ff ff ff
[ 13.476140] saa7133[0]: i2c eeprom c0: ff ff ff ff ff ff ff ff ff ff ff
ff ff ff ff ff
[ 13.476149] saa7133[0]: i2c eeprom d0: ff ff ff ff ff ff ff ff ff ff ff
ff ff ff ff ff
[ 13.476157] saa7133[0]: i2c eeprom e0: ff ff ff ff ff ff ff ff ff ff ff
ff ff ff ff ff
[ 13.476166] saa7133[0]: i2c eeprom f0: ff ff ff ff ff ff ff ff ff ff ff
ff ff ff ff ff
[ 13.508082] tuner 2-0062: chip found @ 0xc4 (saa7133[0])
[ 13.548912] xc2028 2-0062: creating new instance
[ 13.548916] xc2028 2-0062: type set to XCeive xc2028/xc3028 tuner
[ 13.548926] firmware: requesting xc3028-v27.fw
[ 13.999716] input: ImPS/2 Generic Wheel Mouse
as /devices/platform/i8042/serio1/input/input5
[ 14.055433] xc2028 2-0062: Loading 80 firmware images from
xc3028-v27.fw, type: xc2028 firmware, ver 2.7
[ 14.055534] xc2028 2-0062: Loading firmware for type=BASE F8MHZ MTS
(7), id 0000000000000000.
[ 14.055940] xc2028 2-0062: i2c output error: rc = -5 (should be 64)
[ 14.055943] xc2028 2-0062: -5 returned from send
[ 14.055947] xc2028 2-0062: Error -22 while loading base firmware
[ 14.108032] xc2028 2-0062: Loading firmware for type=BASE F8MHZ MTS
(7), id 0000000000000000.
[ 14.108570] xc2028 2-0062: i2c output error: rc = -5 (should be 64)
[ 14.108573] xc2028 2-0062: -5 returned from send
[ 14.108576] xc2028 2-0062: Error -22 while loading base firmware
[ 14.108589] xc2028 2-0062: Loading firmware for type=BASE F8MHZ MTS
(7), id 0000000000000000.
[ 14.109126] xc2028 2-0062: i2c output error: rc = -5 (should be 64)
[ 14.109128] xc2028 2-0062: -5 returned from send
[ 14.109131] xc2028 2-0062: Error -22 while loading base firmware
[ 14.165021] xc2028 2-0062: Loading firmware for type=BASE F8MHZ MTS
(7), id 0000000000000000.
[ 14.165555] xc2028 2-0062: i2c output error: rc = -5 (should be 64)
[ 14.165557] xc2028 2-0062: -5 returned from send
[ 14.165560] xc2028 2-0062: Error -22 while loading base firmware
[ 14.166394] xc2028 2-0062: Error on line 1124: -5
[ 14.173289] saa7133[0]: registered device video0 [v4l2]
[ 14.173451] saa7133[0]: registered device vbi0
[ 14.173507] saa7133[0]: registered device radio0
[ 14.174059] ACPI: PCI Interrupt Link [AAZA] enabled at IRQ 23
[ 14.174064] HDA Intel 0000:00:10.1: PCI INT B -> Link[AAZA] -> GSI 23
(level, low) -> IRQ 23
[ 14.174089] HDA Intel 0000:00:10.1: setting latency timer to 64
[ 14.196322] saa7134 ALSA driver for DMA sound loaded
[ 14.196353] saa7133[0]/alsa: saa7133[0] at 0xfdbfe000 irq 16 registered
as card -2
[ 14.337099] dvb_init() allocating 1 frontend
[ 14.337105] saa7133[0]/dvb: Huh? unknown DVB card?
[ 14.337108] saa7133[0]/dvb: frontend initialization failed
prev parent reply other threads:[~2009-03-14 5:14 UTC|newest]
Thread overview: 5+ messages / expand[flat|nested] mbox.gz Atom feed top
2009-03-12 21:46 [linux-dvb] getting started Rolf Schumacher
2009-03-12 22:02 ` Antti Palosaari
2009-03-12 22:47 ` Rolf Schumacher
2009-03-12 22:04 ` Thomas Kaiser
2009-03-14 5:14 ` Andrew Reay [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1237007658.19797.0.camel@desktop \
--to=certain@tpg.com.au \
--cc=linux-media@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.