From: James Smart <James.Smart@Emulex.Com>
To: linux-scsi <linux-scsi@vger.kernel.org>
Subject: [PATCH 6/17] lpfc 8.3.2 : Addition of SLI4 Interface - Base Support - Part 3 of 6
Date: Fri, 22 May 2009 14:51:59 -0400 [thread overview]
Message-ID: <1243018319.7729.49.camel@ogier> (raw)
Addition of SLI4 Interface - Base Support - Part 3 of 6
Adds new hardware and interface definitions.
Adds new interface routines - utilizing the reorganized layout of the
driver. Adds SLI-4 specific functions for attachment, initialization,
teardown, etc.
Signed-off-by: James Smart <james.smart@emulex.com>
---
lpfc_scsi.h | 2
lpfc_sli.c | 1263 +++++++++++++++++++++++++++++++++++++++++++++++++++++++++--
lpfc_sli.h | 27 +
lpfc_sli4.h | 467 +++++++++++++++++++++
lpfc_vport.c | 23 +
5 files changed, 1748 insertions(+), 34 deletions(-)
diff -upNr a/drivers/scsi/lpfc/lpfc_scsi.h b/drivers/scsi/lpfc/lpfc_scsi.h
--- a/drivers/scsi/lpfc/lpfc_scsi.h 2008-12-16 09:34:12.000000000 -0500
+++ b/drivers/scsi/lpfc/lpfc_scsi.h 2009-05-22 13:16:40.000000000 -0400
@@ -140,6 +140,8 @@ struct lpfc_scsi_buf {
struct fcp_rsp *fcp_rsp;
struct ulp_bde64 *fcp_bpl;
+ dma_addr_t dma_phys_bpl;
+
/* cur_iocbq has phys of the dma-able buffer.
* Iotag is in here
*/
diff -upNr a/drivers/scsi/lpfc/lpfc_sli4.h b/drivers/scsi/lpfc/lpfc_sli4.h
--- a/drivers/scsi/lpfc/lpfc_sli4.h 1969-12-31 19:00:00.000000000 -0500
+++ b/drivers/scsi/lpfc/lpfc_sli4.h 2009-05-22 13:16:40.000000000 -0400
@@ -0,0 +1,467 @@
+/*******************************************************************
+ * This file is part of the Emulex Linux Device Driver for *
+ * Fibre Channel Host Bus Adapters. *
+ * Copyright (C) 2009 Emulex. All rights reserved. *
+ * EMULEX and SLI are trademarks of Emulex. *
+ * www.emulex.com *
+ * *
+ * This program is free software; you can redistribute it and/or *
+ * modify it under the terms of version 2 of the GNU General *
+ * Public License as published by the Free Software Foundation. *
+ * This program is distributed in the hope that it will be useful. *
+ * ALL EXPRESS OR IMPLIED CONDITIONS, REPRESENTATIONS AND *
+ * WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY, *
+ * FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT, ARE *
+ * DISCLAIMED, EXCEPT TO THE EXTENT THAT SUCH DISCLAIMERS ARE HELD *
+ * TO BE LEGALLY INVALID. See the GNU General Public License for *
+ * more details, a copy of which can be found in the file COPYING *
+ * included with this package. *
+ *******************************************************************/
+
+#define LPFC_ACTIVE_MBOX_WAIT_CNT 100
+#define LPFC_RELEASE_NOTIFICATION_INTERVAL 32
+#define LPFC_GET_QE_REL_INT 32
+#define LPFC_RPI_LOW_WATER_MARK 10
+/* Number of SGL entries can be posted in a 4KB nonembedded mbox command */
+#define LPFC_NEMBED_MBOX_SGL_CNT 254
+
+/* Multi-queue arrangement for fast-path FCP work queues */
+#define LPFC_FN_EQN_MAX 8
+#define LPFC_SP_EQN_DEF 1
+#define LPFC_FP_EQN_DEF 1
+#define LPFC_FP_EQN_MIN 1
+#define LPFC_FP_EQN_MAX (LPFC_FN_EQN_MAX - LPFC_SP_EQN_DEF)
+
+#define LPFC_FN_WQN_MAX 32
+#define LPFC_SP_WQN_DEF 1
+#define LPFC_FP_WQN_DEF 4
+#define LPFC_FP_WQN_MIN 1
+#define LPFC_FP_WQN_MAX (LPFC_FN_WQN_MAX - LPFC_SP_WQN_DEF)
+
+/*
+ * Provide the default FCF Record attributes used by the driver
+ * when nonFIP mode is configured and there is no other default
+ * FCF Record attributes.
+ */
+#define LPFC_FCOE_FCF_DEF_INDEX 0
+#define LPFC_FCOE_FCF_GET_FIRST 0xFFFF
+#define LPFC_FCOE_FCF_NEXT_NONE 0xFFFF
+
+/* First 3 bytes of default FCF MAC is specified by FC_MAP */
+#define LPFC_FCOE_FCF_MAC3 0xFF
+#define LPFC_FCOE_FCF_MAC4 0xFF
+#define LPFC_FCOE_FCF_MAC5 0xFE
+#define LPFC_FCOE_FCF_MAP0 0x0E
+#define LPFC_FCOE_FCF_MAP1 0xFC
+#define LPFC_FCOE_FCF_MAP2 0x00
+#define LPFC_FCOE_MAX_RCV_SIZE 0x5AC
+#define LPFC_FCOE_FKA_ADV_PER 0
+#define LPFC_FCOE_FIP_PRIORITY 0x80
+
+enum lpfc_sli4_queue_type {
+ LPFC_EQ,
+ LPFC_GCQ,
+ LPFC_MCQ,
+ LPFC_WCQ,
+ LPFC_RCQ,
+ LPFC_MQ,
+ LPFC_WQ,
+ LPFC_HRQ,
+ LPFC_DRQ
+};
+
+/* The queue sub-type defines the functional purpose of the queue */
+enum lpfc_sli4_queue_subtype {
+ LPFC_NONE,
+ LPFC_MBOX,
+ LPFC_FCP,
+ LPFC_ELS,
+ LPFC_USOL
+};
+
+union sli4_qe {
+ void *address;
+ struct lpfc_eqe *eqe;
+ struct lpfc_cqe *cqe;
+ struct lpfc_mcqe *mcqe;
+ struct lpfc_wcqe_complete *wcqe_complete;
+ struct lpfc_wcqe_release *wcqe_release;
+ struct sli4_wcqe_xri_aborted *wcqe_xri_aborted;
+ struct lpfc_rcqe_complete *rcqe_complete;
+ struct lpfc_mqe *mqe;
+ union lpfc_wqe *wqe;
+ struct lpfc_rqe *rqe;
+};
+
+struct lpfc_queue {
+ struct list_head list;
+ enum lpfc_sli4_queue_type type;
+ enum lpfc_sli4_queue_subtype subtype;
+ struct lpfc_hba *phba;
+ struct list_head child_list;
+ uint32_t entry_count; /* Number of entries to support on the queue */
+ uint32_t entry_size; /* Size of each queue entry. */
+ uint32_t queue_id; /* Queue ID assigned by the hardware */
+ struct list_head page_list;
+ uint32_t page_count; /* Number of pages allocated for this queue */
+
+ uint32_t host_index; /* The host's index for putting or getting */
+ uint32_t hba_index; /* The last known hba index for get or put */
+ union sli4_qe qe[1]; /* array to index entries (must be last) */
+};
+
+struct lpfc_cq_event {
+ struct list_head list;
+ union {
+ struct lpfc_mcqe mcqe_cmpl;
+ struct lpfc_acqe_link acqe_link;
+ struct lpfc_acqe_fcoe acqe_fcoe;
+ struct lpfc_acqe_dcbx acqe_dcbx;
+ struct lpfc_rcqe rcqe_cmpl;
+ struct sli4_wcqe_xri_aborted wcqe_axri;
+ } cqe;
+};
+
+struct lpfc_sli4_link {
+ uint8_t speed;
+ uint8_t duplex;
+ uint8_t status;
+ uint8_t physical;
+ uint8_t fault;
+};
+
+struct lpfc_fcf {
+ uint8_t fabric_name[8];
+ uint8_t mac_addr[6];
+ uint16_t fcf_indx;
+ uint16_t fcfi;
+ uint32_t fcf_flag;
+#define FCF_AVAILABLE 0x01 /* FCF available for discovery */
+#define FCF_REGISTERED 0x02 /* FCF registered with FW */
+#define FCF_DISCOVERED 0x04 /* FCF discovery started */
+#define FCF_BOOT_ENABLE 0x08 /* Boot bios use this FCF */
+#define FCF_IN_USE 0x10 /* Atleast one discovery completed */
+#define FCF_VALID_VLAN 0x20 /* Use the vlan id specified */
+ uint32_t priority;
+ uint32_t addr_mode;
+ uint16_t vlan_id;
+};
+
+#define LPFC_REGION23_SIGNATURE "RG23"
+#define LPFC_REGION23_VERSION 1
+#define LPFC_REGION23_LAST_REC 0xff
+struct lpfc_fip_param_hdr {
+ uint8_t type;
+#define FCOE_PARAM_TYPE 0xA0
+ uint8_t length;
+#define FCOE_PARAM_LENGTH 2
+ uint8_t parm_version;
+#define FIPP_VERSION 0x01
+ uint8_t parm_flags;
+#define lpfc_fip_param_hdr_fipp_mode_SHIFT 6
+#define lpfc_fip_param_hdr_fipp_mode_MASK 0x3
+#define lpfc_fip_param_hdr_fipp_mode_WORD parm_flags
+#define FIPP_MODE_ON 0x2
+#define FIPP_MODE_OFF 0x0
+#define FIPP_VLAN_VALID 0x1
+};
+
+struct lpfc_fcoe_params {
+ uint8_t fc_map[3];
+ uint8_t reserved1;
+ uint16_t vlan_tag;
+ uint8_t reserved[2];
+};
+
+struct lpfc_fcf_conn_hdr {
+ uint8_t type;
+#define FCOE_CONN_TBL_TYPE 0xA1
+ uint8_t length; /* words */
+ uint8_t reserved[2];
+};
+
+struct lpfc_fcf_conn_rec {
+ uint16_t flags;
+#define FCFCNCT_VALID 0x0001
+#define FCFCNCT_BOOT 0x0002
+#define FCFCNCT_PRIMARY 0x0004 /* if not set, Secondary */
+#define FCFCNCT_FBNM_VALID 0x0008
+#define FCFCNCT_SWNM_VALID 0x0010
+#define FCFCNCT_VLAN_VALID 0x0020
+#define FCFCNCT_AM_VALID 0x0040
+#define FCFCNCT_AM_PREFERRED 0x0080 /* if not set, AM Required */
+#define FCFCNCT_AM_SPMA 0x0100 /* if not set, FPMA */
+
+ uint16_t vlan_tag;
+ uint8_t fabric_name[8];
+ uint8_t switch_name[8];
+};
+
+struct lpfc_fcf_conn_entry {
+ struct list_head list;
+ struct lpfc_fcf_conn_rec conn_rec;
+};
+
+/*
+ * Define the host's bootstrap mailbox. This structure contains
+ * the member attributes needed to create, use, and destroy the
+ * bootstrap mailbox region.
+ *
+ * The macro definitions for the bmbx data structure are defined
+ * in lpfc_hw4.h with the register definition.
+ */
+struct lpfc_bmbx {
+ struct lpfc_dmabuf *dmabuf;
+ struct dma_address dma_address;
+ void *avirt;
+ dma_addr_t aphys;
+ uint32_t bmbx_size;
+};
+
+#define LPFC_EQE_SIZE LPFC_EQE_SIZE_4
+
+#define LPFC_EQE_SIZE_4B 4
+#define LPFC_EQE_SIZE_16B 16
+#define LPFC_CQE_SIZE 16
+#define LPFC_WQE_SIZE 64
+#define LPFC_MQE_SIZE 256
+#define LPFC_RQE_SIZE 8
+
+#define LPFC_EQE_DEF_COUNT 1024
+#define LPFC_CQE_DEF_COUNT 256
+#define LPFC_WQE_DEF_COUNT 64
+#define LPFC_MQE_DEF_COUNT 16
+#define LPFC_RQE_DEF_COUNT 512
+
+#define LPFC_QUEUE_NOARM false
+#define LPFC_QUEUE_REARM true
+
+
+/*
+ * SLI4 CT field defines
+ */
+#define SLI4_CT_RPI 0
+#define SLI4_CT_VPI 1
+#define SLI4_CT_VFI 2
+#define SLI4_CT_FCFI 3
+
+#define LPFC_SLI4_MAX_SEGMENT_SIZE 0x10000
+
+/*
+ * SLI4 specific data structures
+ */
+struct lpfc_max_cfg_param {
+ uint16_t max_xri;
+ uint16_t xri_base;
+ uint16_t xri_used;
+ uint16_t max_rpi;
+ uint16_t rpi_base;
+ uint16_t rpi_used;
+ uint16_t max_vpi;
+ uint16_t vpi_base;
+ uint16_t vpi_used;
+ uint16_t max_vfi;
+ uint16_t vfi_base;
+ uint16_t vfi_used;
+ uint16_t max_fcfi;
+ uint16_t fcfi_base;
+ uint16_t fcfi_used;
+ uint16_t max_eq;
+ uint16_t max_rq;
+ uint16_t max_cq;
+ uint16_t max_wq;
+};
+
+struct lpfc_hba;
+/* SLI4 HBA multi-fcp queue handler struct */
+struct lpfc_fcp_eq_hdl {
+ uint32_t idx;
+ struct lpfc_hba *phba;
+};
+
+/* SLI4 HBA data structure entries */
+struct lpfc_sli4_hba {
+ void __iomem *conf_regs_memmap_p; /* Kernel memory mapped address for
+ PCI BAR0, config space registers */
+ void __iomem *ctrl_regs_memmap_p; /* Kernel memory mapped address for
+ PCI BAR1, control registers */
+ void __iomem *drbl_regs_memmap_p; /* Kernel memory mapped address for
+ PCI BAR2, doorbell registers */
+ /* BAR0 PCI config space register memory map */
+ void __iomem *UERRLOregaddr; /* Address to UERR_STATUS_LO register */
+ void __iomem *UERRHIregaddr; /* Address to UERR_STATUS_HI register */
+ void __iomem *ONLINE0regaddr; /* Address to components of internal UE */
+ void __iomem *ONLINE1regaddr; /* Address to components of internal UE */
+#define LPFC_ONLINE_NERR 0xFFFFFFFF
+ void __iomem *SCRATCHPADregaddr; /* Address to scratchpad register */
+ /* BAR1 FCoE function CSR register memory map */
+ void __iomem *STAregaddr; /* Address to HST_STATE register */
+ void __iomem *ISRregaddr; /* Address to HST_ISR register */
+ void __iomem *IMRregaddr; /* Address to HST_IMR register */
+ void __iomem *ISCRregaddr; /* Address to HST_ISCR register */
+ /* BAR2 VF-0 doorbell register memory map */
+ void __iomem *RQDBregaddr; /* Address to RQ_DOORBELL register */
+ void __iomem *WQDBregaddr; /* Address to WQ_DOORBELL register */
+ void __iomem *EQCQDBregaddr; /* Address to EQCQ_DOORBELL register */
+ void __iomem *MQDBregaddr; /* Address to MQ_DOORBELL register */
+ void __iomem *BMBXregaddr; /* Address to BootStrap MBX register */
+
+ struct msix_entry *msix_entries;
+ uint32_t cfg_eqn;
+ struct lpfc_fcp_eq_hdl *fcp_eq_hdl; /* FCP per-WQ handle */
+ /* Pointers to the constructed SLI4 queues */
+ struct lpfc_queue **fp_eq; /* Fast-path event queue */
+ struct lpfc_queue *sp_eq; /* Slow-path event queue */
+ struct lpfc_queue **fcp_wq;/* Fast-path FCP work queue */
+ struct lpfc_queue *mbx_wq; /* Slow-path MBOX work queue */
+ struct lpfc_queue *els_wq; /* Slow-path ELS work queue */
+ struct lpfc_queue *hdr_rq; /* Slow-path Header Receive queue */
+ struct lpfc_queue *dat_rq; /* Slow-path Data Receive queue */
+ struct lpfc_queue **fcp_cq;/* Fast-path FCP compl queue */
+ struct lpfc_queue *mbx_cq; /* Slow-path mailbox complete queue */
+ struct lpfc_queue *els_cq; /* Slow-path ELS response complete queue */
+ struct lpfc_queue *rxq_cq; /* Slow-path unsolicited complete queue */
+
+ /* Setup information for various queue parameters */
+ int eq_esize;
+ int eq_ecount;
+ int cq_esize;
+ int cq_ecount;
+ int wq_esize;
+ int wq_ecount;
+ int mq_esize;
+ int mq_ecount;
+ int rq_esize;
+ int rq_ecount;
+#define LPFC_SP_EQ_MAX_INTR_SEC 10000
+#define LPFC_FP_EQ_MAX_INTR_SEC 10000
+
+ uint32_t intr_enable;
+ struct lpfc_bmbx bmbx;
+ struct lpfc_max_cfg_param max_cfg_param;
+ uint16_t next_xri; /* last_xri - max_cfg_param.xri_base = used */
+ uint16_t next_rpi;
+ uint16_t scsi_xri_max;
+ uint16_t scsi_xri_cnt;
+ struct list_head lpfc_free_sgl_list;
+ struct list_head lpfc_sgl_list;
+ struct lpfc_sglq **lpfc_els_sgl_array;
+ struct list_head lpfc_abts_els_sgl_list;
+ struct lpfc_scsi_buf **lpfc_scsi_psb_array;
+ struct list_head lpfc_abts_scsi_buf_list;
+ uint32_t total_sglq_bufs;
+ struct lpfc_sglq **lpfc_sglq_active_list;
+ struct list_head lpfc_rpi_hdr_list;
+ unsigned long *rpi_bmask;
+ uint16_t rpi_count;
+ struct lpfc_sli4_flags sli4_flags;
+ struct list_head sp_rspiocb_work_queue;
+ struct list_head sp_cqe_event_pool;
+ struct list_head sp_asynce_work_queue;
+ struct list_head sp_fcp_xri_aborted_work_queue;
+ struct list_head sp_els_xri_aborted_work_queue;
+ struct list_head sp_unsol_work_queue;
+ struct lpfc_sli4_link link_state;
+ spinlock_t abts_scsi_buf_list_lock; /* list of aborted SCSI IOs */
+ spinlock_t abts_sgl_list_lock; /* list of aborted els IOs */
+};
+
+enum lpfc_sge_type {
+ GEN_BUFF_TYPE,
+ SCSI_BUFF_TYPE
+};
+
+struct lpfc_sglq {
+ /* lpfc_sglqs are used in double linked lists */
+ struct list_head list;
+ struct list_head clist;
+ enum lpfc_sge_type buff_type; /* is this a scsi sgl */
+ uint16_t iotag; /* pre-assigned IO tag */
+ uint16_t sli4_xritag; /* pre-assigned XRI, (OXID) tag. */
+ struct sli4_sge *sgl; /* pre-assigned SGL */
+ void *virt; /* virtual address. */
+ dma_addr_t phys; /* physical address */
+};
+
+struct lpfc_rpi_hdr {
+ struct list_head list;
+ uint32_t len;
+ struct lpfc_dmabuf *dmabuf;
+ uint32_t page_count;
+ uint32_t start_rpi;
+};
+
+/*
+ * SLI4 specific function prototypes
+ */
+int lpfc_pci_function_reset(struct lpfc_hba *);
+int lpfc_sli4_hba_setup(struct lpfc_hba *);
+int lpfc_sli4_hba_down(struct lpfc_hba *);
+int lpfc_sli4_config(struct lpfc_hba *, struct lpfcMboxq *, uint8_t,
+ uint8_t, uint32_t, bool);
+void lpfc_sli4_mbox_cmd_free(struct lpfc_hba *, struct lpfcMboxq *);
+void lpfc_sli4_mbx_sge_set(struct lpfcMboxq *, uint32_t, dma_addr_t, uint32_t);
+void lpfc_sli4_mbx_sge_get(struct lpfcMboxq *, uint32_t,
+ struct lpfc_mbx_sge *);
+
+void lpfc_sli4_hba_reset(struct lpfc_hba *);
+struct lpfc_queue *lpfc_sli4_queue_alloc(struct lpfc_hba *, uint32_t,
+ uint32_t);
+void lpfc_sli4_queue_free(struct lpfc_queue *);
+uint32_t lpfc_eq_create(struct lpfc_hba *, struct lpfc_queue *, uint16_t);
+uint32_t lpfc_cq_create(struct lpfc_hba *, struct lpfc_queue *,
+ struct lpfc_queue *, uint32_t, uint32_t);
+uint32_t lpfc_mq_create(struct lpfc_hba *, struct lpfc_queue *,
+ struct lpfc_queue *, uint32_t);
+uint32_t lpfc_wq_create(struct lpfc_hba *, struct lpfc_queue *,
+ struct lpfc_queue *, uint32_t);
+uint32_t lpfc_rq_create(struct lpfc_hba *, struct lpfc_queue *,
+ struct lpfc_queue *, struct lpfc_queue *, uint32_t);
+uint32_t lpfc_eq_destroy(struct lpfc_hba *, struct lpfc_queue *);
+uint32_t lpfc_cq_destroy(struct lpfc_hba *, struct lpfc_queue *);
+uint32_t lpfc_mq_destroy(struct lpfc_hba *, struct lpfc_queue *);
+uint32_t lpfc_wq_destroy(struct lpfc_hba *, struct lpfc_queue *);
+uint32_t lpfc_rq_destroy(struct lpfc_hba *, struct lpfc_queue *,
+ struct lpfc_queue *);
+int lpfc_sli4_queue_setup(struct lpfc_hba *);
+void lpfc_sli4_queue_unset(struct lpfc_hba *);
+int lpfc_sli4_post_sgl(struct lpfc_hba *, dma_addr_t, dma_addr_t, uint16_t);
+int lpfc_sli4_repost_scsi_sgl_list(struct lpfc_hba *);
+int lpfc_sli4_remove_all_sgl_pages(struct lpfc_hba *);
+uint16_t lpfc_sli4_next_xritag(struct lpfc_hba *);
+int lpfc_sli4_post_async_mbox(struct lpfc_hba *);
+int lpfc_sli4_post_sgl_list(struct lpfc_hba *phba);
+int lpfc_sli4_post_scsi_sgl_block(struct lpfc_hba *, struct list_head *, int);
+struct lpfc_cq_event *__lpfc_sli4_cq_event_alloc(struct lpfc_hba *);
+struct lpfc_cq_event *lpfc_sli4_cq_event_alloc(struct lpfc_hba *);
+void __lpfc_sli4_cq_event_release(struct lpfc_hba *, struct lpfc_cq_event *);
+void lpfc_sli4_cq_event_release(struct lpfc_hba *, struct lpfc_cq_event *);
+int lpfc_sli4_init_rpi_hdrs(struct lpfc_hba *);
+int lpfc_sli4_post_rpi_hdr(struct lpfc_hba *, struct lpfc_rpi_hdr *);
+int lpfc_sli4_post_all_rpi_hdrs(struct lpfc_hba *);
+struct lpfc_rpi_hdr *lpfc_sli4_create_rpi_hdr(struct lpfc_hba *);
+void lpfc_sli4_remove_rpi_hdrs(struct lpfc_hba *);
+int lpfc_sli4_alloc_rpi(struct lpfc_hba *);
+void lpfc_sli4_free_rpi(struct lpfc_hba *, int);
+void lpfc_sli4_remove_rpis(struct lpfc_hba *);
+void lpfc_sli4_async_event_proc(struct lpfc_hba *);
+int lpfc_sli4_resume_rpi(struct lpfc_nodelist *);
+void lpfc_sli4_fcp_xri_abort_event_proc(struct lpfc_hba *);
+void lpfc_sli4_els_xri_abort_event_proc(struct lpfc_hba *);
+void lpfc_sli4_fcp_xri_aborted(struct lpfc_hba *,
+ struct sli4_wcqe_xri_aborted *);
+void lpfc_sli4_els_xri_aborted(struct lpfc_hba *,
+ struct sli4_wcqe_xri_aborted *);
+int lpfc_sli4_brdreset(struct lpfc_hba *);
+int lpfc_sli4_add_fcf_record(struct lpfc_hba *, struct fcf_record *);
+void lpfc_sli_remove_dflt_fcf(struct lpfc_hba *);
+int lpfc_sli4_get_els_iocb_cnt(struct lpfc_hba *);
+int lpfc_sli4_init_vpi(struct lpfc_hba *, uint16_t);
+uint32_t lpfc_sli4_cq_release(struct lpfc_queue *, bool);
+uint32_t lpfc_sli4_eq_release(struct lpfc_queue *, bool);
+void lpfc_sli4_fcfi_unreg(struct lpfc_hba *, uint16_t);
+int lpfc_sli4_read_fcf_record(struct lpfc_hba *, uint16_t);
+void lpfc_mbx_cmpl_read_fcf_record(struct lpfc_hba *, LPFC_MBOXQ_t *);
+int lpfc_sli4_post_status_check(struct lpfc_hba *);
+uint8_t lpfc_sli4_mbox_opcode_get(struct lpfc_hba *, struct lpfcMboxq *);
+
diff -upNr a/drivers/scsi/lpfc/lpfc_sli.c b/drivers/scsi/lpfc/lpfc_sli.c
--- a/drivers/scsi/lpfc/lpfc_sli.c 2009-05-22 13:14:55.000000000 -0400
+++ b/drivers/scsi/lpfc/lpfc_sli.c 2009-05-22 13:16:40.000000000 -0400
@@ -29,9 +29,12 @@
#include <scsi/scsi_device.h>
#include <scsi/scsi_host.h>
#include <scsi/scsi_transport_fc.h>
+#include <scsi/fc/fc_fs.h>
+#include "lpfc_hw4.h"
#include "lpfc_hw.h"
#include "lpfc_sli.h"
+#include "lpfc_sli4.h"
#include "lpfc_nl.h"
#include "lpfc_disc.h"
#include "lpfc_scsi.h"
@@ -121,6 +124,76 @@ __lpfc_sli_get_iocbq(struct lpfc_hba *ph
}
/**
+ * __lpfc_clear_active_sglq - Remove the active sglq for this XRI.
+ * @phba: Pointer to HBA context object.
+ * @xritag: XRI value.
+ *
+ * This function clears the sglq pointer from the array of acive
+ * sglq's. The xritag that is passed in is used to index into the
+ * array. Before the xritag can be used it needs to be adjusted
+ * by subtracting the xribase.
+ *
+ * Returns sglq ponter = success, NULL = Failure.
+ **/
+static struct lpfc_sglq *
+__lpfc_clear_active_sglq(struct lpfc_hba *phba, uint16_t xritag)
+{
+ uint16_t adj_xri;
+ struct lpfc_sglq *sglq;
+ adj_xri = xritag - phba->sli4_hba.max_cfg_param.xri_base;
+ if (adj_xri > phba->sli4_hba.max_cfg_param.max_xri)
+ return NULL;
+ sglq = phba->sli4_hba.lpfc_sglq_active_list[adj_xri];
+ phba->sli4_hba.lpfc_sglq_active_list[adj_xri] = NULL;
+ return sglq;
+}
+
+/**
+ * __lpfc_get_active_sglq - Get the active sglq for this XRI.
+ * @phba: Pointer to HBA context object.
+ * @xritag: XRI value.
+ *
+ * This function returns the sglq pointer from the array of acive
+ * sglq's. The xritag that is passed in is used to index into the
+ * array. Before the xritag can be used it needs to be adjusted
+ * by subtracting the xribase.
+ *
+ * Returns sglq ponter = success, NULL = Failure.
+ **/
+static struct lpfc_sglq *
+__lpfc_get_active_sglq(struct lpfc_hba *phba, uint16_t xritag)
+{
+ uint16_t adj_xri;
+ struct lpfc_sglq *sglq;
+ adj_xri = xritag - phba->sli4_hba.max_cfg_param.xri_base;
+ if (adj_xri > phba->sli4_hba.max_cfg_param.max_xri)
+ return NULL;
+ sglq = phba->sli4_hba.lpfc_sglq_active_list[adj_xri];
+ return sglq;
+}
+
+/**
+ * __lpfc_sli_get_sglq - Allocates an iocb object from sgl pool
+ * @phba: Pointer to HBA context object.
+ *
+ * This function is called with hbalock held. This function
+ * Gets a new driver sglq object from the sglq list. If the
+ * list is not empty then it is successful, it returns pointer to the newly
+ * allocated sglq object else it returns NULL.
+ **/
+static struct lpfc_sglq *
+__lpfc_sli_get_sglq(struct lpfc_hba *phba)
+{
+ struct list_head *lpfc_sgl_list = &phba->sli4_hba.lpfc_sgl_list;
+ struct lpfc_sglq *sglq = NULL;
+ uint16_t adj_xri;
+ list_remove_head(lpfc_sgl_list, sglq, struct lpfc_sglq, list);
+ adj_xri = sglq->sli4_xritag - phba->sli4_hba.max_cfg_param.xri_base;
+ phba->sli4_hba.lpfc_sglq_active_list[adj_xri] = sglq;
+ return sglq;
+}
+
+/**
* lpfc_sli_get_iocbq - Allocates an iocb object from iocb pool
* @phba: Pointer to HBA context object.
*
@@ -298,6 +371,14 @@ lpfc_sli_iocb_cmd_type(uint8_t iocb_cmnd
case CMD_GEN_REQUEST64_CR:
case CMD_GEN_REQUEST64_CX:
case CMD_XMIT_ELS_RSP64_CX:
+ case DSSCMD_IWRITE64_CR:
+ case DSSCMD_IWRITE64_CX:
+ case DSSCMD_IREAD64_CR:
+ case DSSCMD_IREAD64_CX:
+ case DSSCMD_INVALIDATE_DEK:
+ case DSSCMD_SET_KEK:
+ case DSSCMD_GET_KEK_ID:
+ case DSSCMD_GEN_XFER:
type = LPFC_SOL_IOCB;
break;
case CMD_ABORT_XRI_CN:
@@ -2629,6 +2710,56 @@ lpfc_sli_brdready_s3(struct lpfc_hba *ph
return retval;
}
+/**
+ * lpfc_sli_brdready_s4 - Check for sli4 host ready status
+ * @phba: Pointer to HBA context object.
+ * @mask: Bit mask to be checked.
+ *
+ * This function checks the host status register to check if HBA is
+ * ready. This function will wait in a loop for the HBA to be ready
+ * If the HBA is not ready , the function will will reset the HBA PCI
+ * function again. The function returns 1 when HBA fail to be ready
+ * otherwise returns zero.
+ **/
+static int
+lpfc_sli_brdready_s4(struct lpfc_hba *phba, uint32_t mask)
+{
+ uint32_t status;
+ int retval = 0;
+
+ /* Read the HBA Host Status Register */
+ status = lpfc_sli4_post_status_check(phba);
+
+ if (status) {
+ phba->pport->port_state = LPFC_VPORT_UNKNOWN;
+ lpfc_sli_brdrestart(phba);
+ status = lpfc_sli4_post_status_check(phba);
+ }
+
+ /* Check to see if any errors occurred during init */
+ if (status) {
+ phba->link_state = LPFC_HBA_ERROR;
+ retval = 1;
+ } else
+ phba->sli4_hba.intr_enable = 0;
+
+ return retval;
+}
+
+/**
+ * lpfc_sli_brdready - Wrapper func for checking the hba readyness
+ * @phba: Pointer to HBA context object.
+ * @mask: Bit mask to be checked.
+ *
+ * This routine wraps the actual SLI3 or SLI4 hba readyness check routine
+ * from the API jump table function pointer from the lpfc_hba struct.
+ **/
+int
+lpfc_sli_brdready(struct lpfc_hba *phba, uint32_t mask)
+{
+ return phba->lpfc_sli_brdready(phba, mask);
+}
+
#define BARRIER_TEST_PATTERN (0xdeadbeef)
/**
@@ -2863,7 +2994,66 @@ lpfc_sli_brdreset(struct lpfc_hba *phba)
}
/**
- * lpfc_sli_brdrestart - Restart the HBA
+ * lpfc_sli4_brdreset - Reset a sli-4 HBA
+ * @phba: Pointer to HBA context object.
+ *
+ * This function resets a SLI4 HBA. This function disables PCI layer parity
+ * checking during resets the device. The caller is not required to hold
+ * any locks.
+ *
+ * This function returns 0 always.
+ **/
+int
+lpfc_sli4_brdreset(struct lpfc_hba *phba)
+{
+ struct lpfc_sli *psli = &phba->sli;
+ uint16_t cfg_value;
+ uint8_t qindx;
+
+ /* Reset HBA */
+ lpfc_printf_log(phba, KERN_INFO, LOG_SLI,
+ "0295 Reset HBA Data: x%x x%x\n",
+ phba->pport->port_state, psli->sli_flag);
+
+ /* perform board reset */
+ phba->fc_eventTag = 0;
+ phba->pport->fc_myDID = 0;
+ phba->pport->fc_prevDID = 0;
+
+ /* Turn off parity checking and serr during the physical reset */
+ pci_read_config_word(phba->pcidev, PCI_COMMAND, &cfg_value);
+ pci_write_config_word(phba->pcidev, PCI_COMMAND,
+ (cfg_value &
+ ~(PCI_COMMAND_PARITY | PCI_COMMAND_SERR)));
+
+ spin_lock_irq(&phba->hbalock);
+ psli->sli_flag &= ~(LPFC_PROCESS_LA);
+ phba->fcf.fcf_flag = 0;
+ /* Clean up the child queue list for the CQs */
+ list_del_init(&phba->sli4_hba.mbx_wq->list);
+ list_del_init(&phba->sli4_hba.els_wq->list);
+ list_del_init(&phba->sli4_hba.hdr_rq->list);
+ list_del_init(&phba->sli4_hba.dat_rq->list);
+ list_del_init(&phba->sli4_hba.mbx_cq->list);
+ list_del_init(&phba->sli4_hba.els_cq->list);
+ list_del_init(&phba->sli4_hba.rxq_cq->list);
+ for (qindx = 0; qindx < phba->cfg_fcp_wq_count; qindx++)
+ list_del_init(&phba->sli4_hba.fcp_wq[qindx]->list);
+ for (qindx = 0; qindx < phba->cfg_fcp_eq_count; qindx++)
+ list_del_init(&phba->sli4_hba.fcp_cq[qindx]->list);
+ spin_unlock_irq(&phba->hbalock);
+
+ /* Now physically reset the device */
+ lpfc_printf_log(phba, KERN_INFO, LOG_INIT,
+ "0389 Performing PCI function reset!\n");
+ /* Perform FCoE PCI function reset */
+ lpfc_pci_function_reset(phba);
+
+ return 0;
+}
+
+/**
+ * lpfc_sli_brdrestart_s3 - Restart a sli-3 hba
* @phba: Pointer to HBA context object.
*
* This function is called in the SLI initialization code path to
@@ -2875,8 +3065,8 @@ lpfc_sli_brdreset(struct lpfc_hba *phba)
* The function does not guarantee completion of MBX_RESTART mailbox
* command before the return of this function.
**/
-int
-lpfc_sli_brdrestart(struct lpfc_hba *phba)
+static int
+lpfc_sli_brdrestart_s3(struct lpfc_hba *phba)
{
MAILBOX_t *mb;
struct lpfc_sli *psli;
@@ -2915,7 +3105,7 @@ lpfc_sli_brdrestart(struct lpfc_hba *phb
lpfc_sli_brdreset(phba);
phba->pport->stopped = 0;
phba->link_state = LPFC_INIT_START;
-
+ phba->hba_flag = 0;
spin_unlock_irq(&phba->hbalock);
memset(&psli->lnk_stat_offsets, 0, sizeof(psli->lnk_stat_offsets));
@@ -2930,6 +3120,55 @@ lpfc_sli_brdrestart(struct lpfc_hba *phb
}
/**
+ * lpfc_sli_brdrestart_s4 - Restart the sli-4 hba
+ * @phba: Pointer to HBA context object.
+ *
+ * This function is called in the SLI initialization code path to restart
+ * a SLI4 HBA. The caller is not required to hold any lock.
+ * At the end of the function, it calls lpfc_hba_down_post function to
+ * free any pending commands.
+ **/
+static int
+lpfc_sli_brdrestart_s4(struct lpfc_hba *phba)
+{
+ struct lpfc_sli *psli = &phba->sli;
+
+
+ /* Restart HBA */
+ lpfc_printf_log(phba, KERN_INFO, LOG_SLI,
+ "0296 Restart HBA Data: x%x x%x\n",
+ phba->pport->port_state, psli->sli_flag);
+
+ lpfc_sli4_brdreset(phba);
+
+ spin_lock_irq(&phba->hbalock);
+ phba->pport->stopped = 0;
+ phba->link_state = LPFC_INIT_START;
+ phba->hba_flag = 0;
+ spin_unlock_irq(&phba->hbalock);
+
+ memset(&psli->lnk_stat_offsets, 0, sizeof(psli->lnk_stat_offsets));
+ psli->stats_start = get_seconds();
+
+ lpfc_hba_down_post(phba);
+
+ return 0;
+}
+
+/**
+ * lpfc_sli_brdrestart - Wrapper func for restarting hba
+ * @phba: Pointer to HBA context object.
+ *
+ * This routine wraps the actual SLI3 or SLI4 hba restart routine from the
+ * API jump table function pointer from the lpfc_hba struct.
+**/
+int
+lpfc_sli_brdrestart(struct lpfc_hba *phba)
+{
+ return phba->lpfc_sli_brdrestart(phba);
+}
+
+/**
* lpfc_sli_chipset_init - Wait for the restart of the HBA after a restart
* @phba: Pointer to HBA context object.
*
@@ -3353,6 +3592,488 @@ lpfc_sli_hba_setup_error:
return rc;
}
+/**
+ * lpfc_sli4_read_fcoe_params - Read fcoe params from conf region
+ * @phba: Pointer to HBA context object.
+ * @mboxq: mailbox pointer.
+ * This function issue a dump mailbox command to read config region
+ * 23 and parse the records in the region and populate driver
+ * data structure.
+ **/
+static int
+lpfc_sli4_read_fcoe_params(struct lpfc_hba *phba,
+ LPFC_MBOXQ_t *mboxq)
+{
+ struct lpfc_dmabuf *mp;
+ struct lpfc_mqe *mqe;
+ uint32_t data_length;
+ int rc;
+
+ /* Program the default value of vlan_id and fc_map */
+ phba->valid_vlan = 0;
+ phba->fc_map[0] = LPFC_FCOE_FCF_MAP0;
+ phba->fc_map[1] = LPFC_FCOE_FCF_MAP1;
+ phba->fc_map[2] = LPFC_FCOE_FCF_MAP2;
+
+ mqe = &mboxq->u.mqe;
+ if (lpfc_dump_fcoe_param(phba, mboxq))
+ return -ENOMEM;
+
+ mp = (struct lpfc_dmabuf *) mboxq->context1;
+ rc = lpfc_sli_issue_mbox(phba, mboxq, MBX_POLL);
+
+ lpfc_printf_log(phba, KERN_INFO, LOG_MBOX | LOG_SLI,
+ "(%d):2571 Mailbox cmd x%x Status x%x "
+ "Data: x%x x%x x%x x%x x%x x%x x%x x%x x%x "
+ "x%x x%x x%x x%x x%x x%x x%x x%x x%x "
+ "CQ: x%x x%x x%x x%x\n",
+ mboxq->vport ? mboxq->vport->vpi : 0,
+ bf_get(lpfc_mqe_command, mqe),
+ bf_get(lpfc_mqe_status, mqe),
+ mqe->un.mb_words[0], mqe->un.mb_words[1],
+ mqe->un.mb_words[2], mqe->un.mb_words[3],
+ mqe->un.mb_words[4], mqe->un.mb_words[5],
+ mqe->un.mb_words[6], mqe->un.mb_words[7],
+ mqe->un.mb_words[8], mqe->un.mb_words[9],
+ mqe->un.mb_words[10], mqe->un.mb_words[11],
+ mqe->un.mb_words[12], mqe->un.mb_words[13],
+ mqe->un.mb_words[14], mqe->un.mb_words[15],
+ mqe->un.mb_words[16], mqe->un.mb_words[50],
+ mboxq->mcqe.word0,
+ mboxq->mcqe.mcqe_tag0, mboxq->mcqe.mcqe_tag1,
+ mboxq->mcqe.trailer);
+
+ if (rc) {
+ lpfc_mbuf_free(phba, mp->virt, mp->phys);
+ kfree(mp);
+ return -EIO;
+ }
+ data_length = mqe->un.mb_words[5];
+ if (data_length > DMP_FCOEPARAM_RGN_SIZE)
+ return -EIO;
+
+ lpfc_parse_fcoe_conf(phba, mp->virt, data_length);
+ lpfc_mbuf_free(phba, mp->virt, mp->phys);
+ kfree(mp);
+ return 0;
+}
+
+/**
+ * lpfc_sli4_read_rev - Issue READ_REV and collect vpd data
+ * @phba: pointer to lpfc hba data structure.
+ * @mboxq: pointer to the LPFC_MBOXQ_t structure.
+ * @vpd: pointer to the memory to hold resulting port vpd data.
+ * @vpd_size: On input, the number of bytes allocated to @vpd.
+ * On output, the number of data bytes in @vpd.
+ *
+ * This routine executes a READ_REV SLI4 mailbox command. In
+ * addition, this routine gets the port vpd data.
+ *
+ * Return codes
+ * 0 - sucessful
+ * ENOMEM - could not allocated memory.
+ **/
+static int
+lpfc_sli4_read_rev(struct lpfc_hba *phba, LPFC_MBOXQ_t *mboxq,
+ uint8_t *vpd, uint32_t *vpd_size)
+{
+ int rc = 0;
+ uint32_t dma_size;
+ struct lpfc_dmabuf *dmabuf;
+ struct lpfc_mqe *mqe;
+
+ dmabuf = kzalloc(sizeof(struct lpfc_dmabuf), GFP_KERNEL);
+ if (!dmabuf)
+ return -ENOMEM;
+
+ /*
+ * Get a DMA buffer for the vpd data resulting from the READ_REV
+ * mailbox command.
+ */
+ dma_size = *vpd_size;
+ dmabuf->virt = dma_alloc_coherent(&phba->pcidev->dev,
+ dma_size,
+ &dmabuf->phys,
+ GFP_KERNEL);
+ if (!dmabuf->virt) {
+ kfree(dmabuf);
+ return -ENOMEM;
+ }
+ memset(dmabuf->virt, 0, dma_size);
+
+ /*
+ * The SLI4 implementation of READ_REV conflicts at word1,
+ * bits 31:16 and SLI4 adds vpd functionality not present
+ * in SLI3. This code corrects the conflicts.
+ */
+ lpfc_read_rev(phba, mboxq);
+ mqe = &mboxq->u.mqe;
+ mqe->un.read_rev.vpd_paddr_high = putPaddrHigh(dmabuf->phys);
+ mqe->un.read_rev.vpd_paddr_low = putPaddrLow(dmabuf->phys);
+ mqe->un.read_rev.word1 &= 0x0000FFFF;
+ bf_set(lpfc_mbx_rd_rev_vpd, &mqe->un.read_rev, 1);
+ bf_set(lpfc_mbx_rd_rev_avail_len, &mqe->un.read_rev, dma_size);
+
+ rc = lpfc_sli_issue_mbox(phba, mboxq, MBX_POLL);
+ if (rc) {
+ dma_free_coherent(&phba->pcidev->dev, dma_size,
+ dmabuf->virt, dmabuf->phys);
+ return -EIO;
+ }
+
+ lpfc_printf_log(phba, KERN_INFO, LOG_MBOX | LOG_SLI,
+ "(%d):0380 Mailbox cmd x%x Status x%x "
+ "Data: x%x x%x x%x x%x x%x x%x x%x x%x x%x "
+ "x%x x%x x%x x%x x%x x%x x%x x%x x%x "
+ "CQ: x%x x%x x%x x%x\n",
+ mboxq->vport ? mboxq->vport->vpi : 0,
+ bf_get(lpfc_mqe_command, mqe),
+ bf_get(lpfc_mqe_status, mqe),
+ mqe->un.mb_words[0], mqe->un.mb_words[1],
+ mqe->un.mb_words[2], mqe->un.mb_words[3],
+ mqe->un.mb_words[4], mqe->un.mb_words[5],
+ mqe->un.mb_words[6], mqe->un.mb_words[7],
+ mqe->un.mb_words[8], mqe->un.mb_words[9],
+ mqe->un.mb_words[10], mqe->un.mb_words[11],
+ mqe->un.mb_words[12], mqe->un.mb_words[13],
+ mqe->un.mb_words[14], mqe->un.mb_words[15],
+ mqe->un.mb_words[16], mqe->un.mb_words[50],
+ mboxq->mcqe.word0,
+ mboxq->mcqe.mcqe_tag0, mboxq->mcqe.mcqe_tag1,
+ mboxq->mcqe.trailer);
+
+ /*
+ * The available vpd length cannot be bigger than the
+ * DMA buffer passed to the port. Catch the less than
+ * case and update the caller's size.
+ */
+ if (mqe->un.read_rev.avail_vpd_len < *vpd_size)
+ *vpd_size = mqe->un.read_rev.avail_vpd_len;
+
+ lpfc_sli_pcimem_bcopy(dmabuf->virt, vpd, *vpd_size);
+ dma_free_coherent(&phba->pcidev->dev, dma_size,
+ dmabuf->virt, dmabuf->phys);
+ kfree(dmabuf);
+ return 0;
+}
+
+/**
+ * lpfc_sli4_arm_cqeq_intr - Arm sli-4 device completion and event queues
+ * @phba: pointer to lpfc hba data structure.
+ *
+ * This routine is called to explicitly arm the SLI4 device's completion and
+ * event queues
+ **/
+static void
+lpfc_sli4_arm_cqeq_intr(struct lpfc_hba *phba)
+{
+ uint8_t fcp_eqidx;
+
+ lpfc_sli4_cq_release(phba->sli4_hba.mbx_cq, LPFC_QUEUE_REARM);
+ lpfc_sli4_cq_release(phba->sli4_hba.els_cq, LPFC_QUEUE_REARM);
+ lpfc_sli4_cq_release(phba->sli4_hba.rxq_cq, LPFC_QUEUE_REARM);
+ for (fcp_eqidx = 0; fcp_eqidx < phba->cfg_fcp_eq_count; fcp_eqidx++)
+ lpfc_sli4_cq_release(phba->sli4_hba.fcp_cq[fcp_eqidx],
+ LPFC_QUEUE_REARM);
+ lpfc_sli4_eq_release(phba->sli4_hba.sp_eq, LPFC_QUEUE_REARM);
+ for (fcp_eqidx = 0; fcp_eqidx < phba->cfg_fcp_eq_count; fcp_eqidx++)
+ lpfc_sli4_eq_release(phba->sli4_hba.fp_eq[fcp_eqidx],
+ LPFC_QUEUE_REARM);
+}
+
+/**
+ * lpfc_sli4_hba_setup - SLI4 device intialization PCI function
+ * @phba: Pointer to HBA context object.
+ *
+ * This function is the main SLI4 device intialization PCI function. This
+ * function is called by the HBA intialization code, HBA reset code and
+ * HBA error attention handler code. Caller is not required to hold any
+ * locks.
+ **/
+int
+lpfc_sli4_hba_setup(struct lpfc_hba *phba)
+{
+ int rc;
+ LPFC_MBOXQ_t *mboxq;
+ struct lpfc_mqe *mqe;
+ uint8_t *vpd;
+ uint32_t vpd_size;
+ uint32_t ftr_rsp = 0;
+ struct Scsi_Host *shost = lpfc_shost_from_vport(phba->pport);
+ struct lpfc_vport *vport = phba->pport;
+ struct lpfc_dmabuf *mp;
+
+ /* Perform a PCI function reset to start from clean */
+ rc = lpfc_pci_function_reset(phba);
+ if (unlikely(rc))
+ return -ENODEV;
+
+ /* Check the HBA Host Status Register for readyness */
+ rc = lpfc_sli4_post_status_check(phba);
+ if (unlikely(rc))
+ return -ENODEV;
+ else {
+ spin_lock_irq(&phba->hbalock);
+ phba->sli.sli_flag |= LPFC_SLI_ACTIVE;
+ spin_unlock_irq(&phba->hbalock);
+ }
+
+ /*
+ * Allocate a single mailbox container for initializing the
+ * port.
+ */
+ mboxq = (LPFC_MBOXQ_t *) mempool_alloc(phba->mbox_mem_pool, GFP_KERNEL);
+ if (!mboxq)
+ return -ENOMEM;
+
+ /*
+ * Continue initialization with default values even if driver failed
+ * to read FCoE param config regions
+ */
+ if (lpfc_sli4_read_fcoe_params(phba, mboxq))
+ lpfc_printf_log(phba, KERN_ERR, LOG_MBOX | LOG_INIT,
+ "2570 Failed to read FCoE parameters \n");
+
+ /* Issue READ_REV to collect vpd and FW information. */
+ vpd_size = PAGE_SIZE;
+ vpd = kzalloc(vpd_size, GFP_KERNEL);
+ if (!vpd) {
+ rc = -ENOMEM;
+ goto out_free_mbox;
+ }
+
+ rc = lpfc_sli4_read_rev(phba, mboxq, vpd, &vpd_size);
+ if (unlikely(rc))
+ goto out_free_vpd;
+
+ mqe = &mboxq->u.mqe;
+ if ((bf_get(lpfc_mbx_rd_rev_sli_lvl,
+ &mqe->un.read_rev) != LPFC_SLI_REV4) ||
+ (bf_get(lpfc_mbx_rd_rev_fcoe, &mqe->un.read_rev) == 0)) {
+ lpfc_printf_log(phba, KERN_ERR, LOG_MBOX | LOG_SLI,
+ "0376 READ_REV Error. SLI Level %d "
+ "FCoE enabled %d\n",
+ bf_get(lpfc_mbx_rd_rev_sli_lvl, &mqe->un.read_rev),
+ bf_get(lpfc_mbx_rd_rev_fcoe, &mqe->un.read_rev));
+ rc = -EIO;
+ goto out_free_vpd;
+ }
+ /* Single threaded at this point, no need for lock */
+ spin_lock_irq(&phba->hbalock);
+ phba->hba_flag |= HBA_FCOE_SUPPORT;
+ spin_unlock_irq(&phba->hbalock);
+ /*
+ * Evaluate the read rev and vpd data. Populate the driver
+ * state with the results. If this routine fails, the failure
+ * is not fatal as the driver will use generic values.
+ */
+ rc = lpfc_parse_vpd(phba, vpd, vpd_size);
+ if (unlikely(!rc)) {
+ lpfc_printf_log(phba, KERN_ERR, LOG_MBOX | LOG_SLI,
+ "0377 Error %d parsing vpd. "
+ "Using defaults.\n", rc);
+ rc = 0;
+ }
+
+ /* By now, we should determine the SLI revision, hard code for now */
+ phba->sli_rev = LPFC_SLI_REV4;
+
+ /*
+ * Discover the port's supported feature set and match it against the
+ * hosts requests.
+ */
+ lpfc_request_features(phba, mboxq);
+ rc = lpfc_sli_issue_mbox(phba, mboxq, MBX_POLL);
+ if (unlikely(rc)) {
+ rc = -EIO;
+ goto out_free_vpd;
+ }
+
+ /*
+ * The port must support FCP initiator mode as this is the
+ * only mode running in the host.
+ */
+ if (!(bf_get(lpfc_mbx_rq_ftr_rsp_fcpi, &mqe->un.req_ftrs))) {
+ lpfc_printf_log(phba, KERN_WARNING, LOG_MBOX | LOG_SLI,
+ "0378 No support for fcpi mode.\n");
+ ftr_rsp++;
+ }
+
+ /*
+ * If the port cannot support the host's requested features
+ * then turn off the global config parameters to disable the
+ * feature in the driver. This is not a fatal error.
+ */
+ if ((phba->cfg_enable_bg) &&
+ !(bf_get(lpfc_mbx_rq_ftr_rsp_dif, &mqe->un.req_ftrs)))
+ ftr_rsp++;
+
+ if (phba->max_vpi && phba->cfg_enable_npiv &&
+ !(bf_get(lpfc_mbx_rq_ftr_rsp_npiv, &mqe->un.req_ftrs)))
+ ftr_rsp++;
+
+ if (ftr_rsp) {
+ lpfc_printf_log(phba, KERN_WARNING, LOG_MBOX | LOG_SLI,
+ "0379 Feature Mismatch Data: x%08x %08x "
+ "x%x x%x x%x\n", mqe->un.req_ftrs.word2,
+ mqe->un.req_ftrs.word3, phba->cfg_enable_bg,
+ phba->cfg_enable_npiv, phba->max_vpi);
+ if (!(bf_get(lpfc_mbx_rq_ftr_rsp_dif, &mqe->un.req_ftrs)))
+ phba->cfg_enable_bg = 0;
+ if (!(bf_get(lpfc_mbx_rq_ftr_rsp_npiv, &mqe->un.req_ftrs)))
+ phba->cfg_enable_npiv = 0;
+ }
+
+ /* These SLI3 features are assumed in SLI4 */
+ spin_lock_irq(&phba->hbalock);
+ phba->sli3_options |= (LPFC_SLI3_NPIV_ENABLED | LPFC_SLI3_HBQ_ENABLED);
+ spin_unlock_irq(&phba->hbalock);
+
+ /* Read the port's service parameters. */
+ lpfc_read_sparam(phba, mboxq, vport->vpi);
+ mboxq->vport = vport;
+ rc = lpfc_sli_issue_mbox(phba, mboxq, MBX_POLL);
+ mp = (struct lpfc_dmabuf *) mboxq->context1;
+ if (rc == MBX_SUCCESS) {
+ memcpy(&vport->fc_sparam, mp->virt, sizeof(struct serv_parm));
+ rc = 0;
+ }
+
+ /*
+ * This memory was allocated by the lpfc_read_sparam routine. Release
+ * it to the mbuf pool.
+ */
+ lpfc_mbuf_free(phba, mp->virt, mp->phys);
+ kfree(mp);
+ mboxq->context1 = NULL;
+ if (unlikely(rc)) {
+ lpfc_printf_log(phba, KERN_ERR, LOG_MBOX | LOG_SLI,
+ "0382 READ_SPARAM command failed "
+ "status %d, mbxStatus x%x\n",
+ rc, bf_get(lpfc_mqe_status, mqe));
+ phba->link_state = LPFC_HBA_ERROR;
+ rc = -EIO;
+ goto out_free_vpd;
+ }
+
+ if (phba->cfg_soft_wwnn)
+ u64_to_wwn(phba->cfg_soft_wwnn,
+ vport->fc_sparam.nodeName.u.wwn);
+ if (phba->cfg_soft_wwpn)
+ u64_to_wwn(phba->cfg_soft_wwpn,
+ vport->fc_sparam.portName.u.wwn);
+ memcpy(&vport->fc_nodename, &vport->fc_sparam.nodeName,
+ sizeof(struct lpfc_name));
+ memcpy(&vport->fc_portname, &vport->fc_sparam.portName,
+ sizeof(struct lpfc_name));
+
+ /* Update the fc_host data structures with new wwn. */
+ fc_host_node_name(shost) = wwn_to_u64(vport->fc_nodename.u.wwn);
+ fc_host_port_name(shost) = wwn_to_u64(vport->fc_portname.u.wwn);
+
+ /* Register SGL pool to the device using non-embedded mailbox command */
+ rc = lpfc_sli4_post_sgl_list(phba);
+ if (unlikely(rc)) {
+ lpfc_printf_log(phba, KERN_ERR, LOG_MBOX | LOG_SLI,
+ "0582 Error %d during sgl post operation", rc);
+ rc = -ENODEV;
+ goto out_free_vpd;
+ }
+
+ /* Register SCSI SGL pool to the device */
+ rc = lpfc_sli4_repost_scsi_sgl_list(phba);
+ if (unlikely(rc)) {
+ lpfc_printf_log(phba, KERN_WARNING, LOG_MBOX | LOG_SLI,
+ "0383 Error %d during scsi sgl post opeation",
+ rc);
+ /* Some Scsi buffers were moved to the abort scsi list */
+ /* A pci function reset will repost them */
+ rc = -ENODEV;
+ goto out_free_vpd;
+ }
+
+ /* Post the rpi header region to the device. */
+ rc = lpfc_sli4_post_all_rpi_hdrs(phba);
+ if (unlikely(rc)) {
+ lpfc_printf_log(phba, KERN_ERR, LOG_MBOX | LOG_SLI,
+ "0393 Error %d during rpi post operation\n",
+ rc);
+ rc = -ENODEV;
+ goto out_free_vpd;
+ }
+ /* Temporary initialization of lpfc_fip_flag to non-fip */
+ bf_set(lpfc_fip_flag, &phba->sli4_hba.sli4_flags, 0);
+
+ /* Set up all the queues to the device */
+ rc = lpfc_sli4_queue_setup(phba);
+ if (unlikely(rc)) {
+ lpfc_printf_log(phba, KERN_ERR, LOG_MBOX | LOG_SLI,
+ "0381 Error %d during queue setup.\n ", rc);
+ goto out_stop_timers;
+ }
+
+ /* Arm the CQs and then EQs on device */
+ lpfc_sli4_arm_cqeq_intr(phba);
+
+ /* Indicate device interrupt mode */
+ phba->sli4_hba.intr_enable = 1;
+
+ /* Allow asynchronous mailbox command to go through */
+ spin_lock_irq(&phba->hbalock);
+ phba->sli.sli_flag &= ~LPFC_SLI_ASYNC_MBX_BLK;
+ spin_unlock_irq(&phba->hbalock);
+
+ /* Post receive buffers to the device */
+ lpfc_sli4_rb_setup(phba);
+
+ /* Start the ELS watchdog timer */
+ /*
+ * The driver for SLI4 is not yet ready to process timeouts
+ * or interrupts. Once it is, the comment bars can be removed.
+ */
+ /* mod_timer(&vport->els_tmofunc,
+ * jiffies + HZ * (phba->fc_ratov*2)); */
+
+ /* Start heart beat timer */
+ mod_timer(&phba->hb_tmofunc,
+ jiffies + HZ * LPFC_HB_MBOX_INTERVAL);
+ phba->hb_outstanding = 0;
+ phba->last_completion_time = jiffies;
+
+ /* Start error attention (ERATT) polling timer */
+ mod_timer(&phba->eratt_poll, jiffies + HZ * LPFC_ERATT_POLL_INTERVAL);
+
+ /*
+ * The port is ready, set the host's link state to LINK_DOWN
+ * in preparation for link interrupts.
+ */
+ lpfc_init_link(phba, mboxq, phba->cfg_topology, phba->cfg_link_speed);
+ mboxq->mbox_cmpl = lpfc_sli_def_mbox_cmpl;
+ lpfc_set_loopback_flag(phba);
+ /* Change driver state to LPFC_LINK_DOWN right before init link */
+ spin_lock_irq(&phba->hbalock);
+ phba->link_state = LPFC_LINK_DOWN;
+ spin_unlock_irq(&phba->hbalock);
+ rc = lpfc_sli_issue_mbox(phba, mboxq, MBX_NOWAIT);
+ if (unlikely(rc != MBX_NOT_FINISHED)) {
+ kfree(vpd);
+ return 0;
+ } else
+ rc = -EIO;
+
+ /* Unset all the queues set up in this routine when error out */
+ if (rc)
+ lpfc_sli4_queue_unset(phba);
+
+out_stop_timers:
+ if (rc)
+ lpfc_stop_hba_timers(phba);
+out_free_vpd:
+ kfree(vpd);
+out_free_mbox:
+ mempool_free(mboxq, phba->mbox_mem_pool);
+ return rc;
+}
/**
* lpfc_mbox_timeout - Timeout call back function for mbox timer
@@ -3812,13 +4533,420 @@ lpfc_sli_issue_mbox_s3(struct lpfc_hba *
out_not_finished:
if (processing_queue) {
- pmbox->mb.mbxStatus = MBX_NOT_FINISHED;
+ pmbox->u.mb.mbxStatus = MBX_NOT_FINISHED;
lpfc_mbox_cmpl_put(phba, pmbox);
}
return MBX_NOT_FINISHED;
}
/**
+ * lpfc_sli4_post_sync_mbox - Post an SLI4 mailbox to the bootstrap mailbox
+ * @phba: Pointer to HBA context object.
+ * @mboxq: Pointer to mailbox object.
+ *
+ * The function posts a mailbox to the port. The mailbox is expected
+ * to be comletely filled in and ready for the port to operate on it.
+ * This routine executes a synchronous completion operation on the
+ * mailbox by polling for its completion.
+ *
+ * The caller must not be holding any locks when calling this routine.
+ *
+ * Returns:
+ * MBX_SUCCESS - mailbox posted successfully
+ * Any of the MBX error values.
+ **/
+static int
+lpfc_sli4_post_sync_mbox(struct lpfc_hba *phba, LPFC_MBOXQ_t *mboxq)
+{
+ int rc = MBX_SUCCESS;
+ unsigned long iflag;
+ uint32_t db_ready;
+ uint32_t mcqe_status;
+ uint32_t mbx_cmnd;
+ unsigned long timeout;
+ struct lpfc_sli *psli = &phba->sli;
+ struct lpfc_mqe *mb = &mboxq->u.mqe;
+ struct lpfc_bmbx_create *mbox_rgn;
+ struct dma_address *dma_address;
+ struct lpfc_register bmbx_reg;
+
+ /*
+ * Only one mailbox can be active to the bootstrap mailbox region
+ * at a time and there is no queueing provided.
+ */
+ spin_lock_irqsave(&phba->hbalock, iflag);
+ if (psli->sli_flag & LPFC_SLI_MBOX_ACTIVE) {
+ spin_unlock_irqrestore(&phba->hbalock, iflag);
+ lpfc_printf_log(phba, KERN_ERR, LOG_MBOX | LOG_SLI,
+ "(%d):2532 Mailbox command x%x (x%x) "
+ "cannot issue Data: x%x x%x\n",
+ mboxq->vport ? mboxq->vport->vpi : 0,
+ mboxq->u.mb.mbxCommand,
+ lpfc_sli4_mbox_opcode_get(phba, mboxq),
+ psli->sli_flag, MBX_POLL);
+ return MBXERR_ERROR;
+ }
+ /* The server grabs the token and owns it until release */
+ psli->sli_flag |= LPFC_SLI_MBOX_ACTIVE;
+ phba->sli.mbox_active = mboxq;
+ spin_unlock_irqrestore(&phba->hbalock, iflag);
+
+ /*
+ * Initialize the bootstrap memory region to avoid stale data areas
+ * in the mailbox post. Then copy the caller's mailbox contents to
+ * the bmbx mailbox region.
+ */
+ mbx_cmnd = bf_get(lpfc_mqe_command, mb);
+ memset(phba->sli4_hba.bmbx.avirt, 0, sizeof(struct lpfc_bmbx_create));
+ lpfc_sli_pcimem_bcopy(mb, phba->sli4_hba.bmbx.avirt,
+ sizeof(struct lpfc_mqe));
+
+ /* Post the high mailbox dma address to the port and wait for ready. */
+ dma_address = &phba->sli4_hba.bmbx.dma_address;
+ writel(dma_address->addr_hi, phba->sli4_hba.BMBXregaddr);
+
+ timeout = msecs_to_jiffies(lpfc_mbox_tmo_val(phba, mbx_cmnd)
+ * 1000) + jiffies;
+ do {
+ bmbx_reg.word0 = readl(phba->sli4_hba.BMBXregaddr);
+ db_ready = bf_get(lpfc_bmbx_rdy, &bmbx_reg);
+ if (!db_ready)
+ msleep(2);
+
+ if (time_after(jiffies, timeout)) {
+ rc = MBXERR_ERROR;
+ goto exit;
+ }
+ } while (!db_ready);
+
+ /* Post the low mailbox dma address to the port. */
+ writel(dma_address->addr_lo, phba->sli4_hba.BMBXregaddr);
+ timeout = msecs_to_jiffies(lpfc_mbox_tmo_val(phba, mbx_cmnd)
+ * 1000) + jiffies;
+ do {
+ bmbx_reg.word0 = readl(phba->sli4_hba.BMBXregaddr);
+ db_ready = bf_get(lpfc_bmbx_rdy, &bmbx_reg);
+ if (!db_ready)
+ msleep(2);
+
+ if (time_after(jiffies, timeout)) {
+ rc = MBXERR_ERROR;
+ goto exit;
+ }
+ } while (!db_ready);
+
+ /*
+ * Read the CQ to ensure the mailbox has completed.
+ * If so, update the mailbox status so that the upper layers
+ * can complete the request normally.
+ */
+ lpfc_sli_pcimem_bcopy(phba->sli4_hba.bmbx.avirt, mb,
+ sizeof(struct lpfc_mqe));
+ mbox_rgn = (struct lpfc_bmbx_create *) phba->sli4_hba.bmbx.avirt;
+ lpfc_sli_pcimem_bcopy(&mbox_rgn->mcqe, &mboxq->mcqe,
+ sizeof(struct lpfc_mcqe));
+ mcqe_status = bf_get(lpfc_mcqe_status, &mbox_rgn->mcqe);
+
+ /* Prefix the mailbox status with range x4000 to note SLI4 status. */
+ if (mcqe_status != MB_CQE_STATUS_SUCCESS) {
+ bf_set(lpfc_mqe_status, mb, LPFC_MBX_ERROR_RANGE | mcqe_status);
+ rc = MBXERR_ERROR;
+ }
+
+ lpfc_printf_log(phba, KERN_INFO, LOG_MBOX | LOG_SLI,
+ "(%d):0356 Mailbox cmd x%x (x%x) Status x%x "
+ "Data: x%x x%x x%x x%x x%x x%x x%x x%x x%x x%x x%x"
+ " x%x x%x CQ: x%x x%x x%x x%x\n",
+ mboxq->vport ? mboxq->vport->vpi : 0,
+ mbx_cmnd, lpfc_sli4_mbox_opcode_get(phba, mboxq),
+ bf_get(lpfc_mqe_status, mb),
+ mb->un.mb_words[0], mb->un.mb_words[1],
+ mb->un.mb_words[2], mb->un.mb_words[3],
+ mb->un.mb_words[4], mb->un.mb_words[5],
+ mb->un.mb_words[6], mb->un.mb_words[7],
+ mb->un.mb_words[8], mb->un.mb_words[9],
+ mb->un.mb_words[10], mb->un.mb_words[11],
+ mb->un.mb_words[12], mboxq->mcqe.word0,
+ mboxq->mcqe.mcqe_tag0, mboxq->mcqe.mcqe_tag1,
+ mboxq->mcqe.trailer);
+exit:
+ /* We are holding the token, no needed for lock when release */
+ spin_lock_irqsave(&phba->hbalock, iflag);
+ psli->sli_flag &= ~LPFC_SLI_MBOX_ACTIVE;
+ phba->sli.mbox_active = NULL;
+ spin_unlock_irqrestore(&phba->hbalock, iflag);
+ return rc;
+}
+
+/**
+ * lpfc_sli_issue_mbox_s4 - Issue an SLI4 mailbox command to firmware
+ * @phba: Pointer to HBA context object.
+ * @pmbox: Pointer to mailbox object.
+ * @flag: Flag indicating how the mailbox need to be processed.
+ *
+ * This function is called by discovery code and HBA management code to submit
+ * a mailbox command to firmware with SLI-4 interface spec.
+ *
+ * Return codes the caller owns the mailbox command after the return of the
+ * function.
+ **/
+static int
+lpfc_sli_issue_mbox_s4(struct lpfc_hba *phba, LPFC_MBOXQ_t *mboxq,
+ uint32_t flag)
+{
+ struct lpfc_sli *psli = &phba->sli;
+ unsigned long iflags;
+ int rc;
+
+ /* Detect polling mode and jump to a handler */
+ if (!phba->sli4_hba.intr_enable) {
+ if (flag == MBX_POLL)
+ rc = lpfc_sli4_post_sync_mbox(phba, mboxq);
+ else
+ rc = -EIO;
+ if (rc != MBX_SUCCESS)
+ lpfc_printf_log(phba, KERN_ERR, LOG_MBOX | LOG_SLI,
+ "(%d):2541 Mailbox command x%x "
+ "(x%x) cannot issue Data: x%x x%x\n",
+ mboxq->vport ? mboxq->vport->vpi : 0,
+ mboxq->u.mb.mbxCommand,
+ lpfc_sli4_mbox_opcode_get(phba, mboxq),
+ psli->sli_flag, flag);
+ return rc;
+ } else if (flag == MBX_POLL) {
+ lpfc_printf_log(phba, KERN_ERR, LOG_MBOX | LOG_SLI,
+ "(%d):2542 Mailbox command x%x (x%x) "
+ "cannot issue Data: x%x x%x\n",
+ mboxq->vport ? mboxq->vport->vpi : 0,
+ mboxq->u.mb.mbxCommand,
+ lpfc_sli4_mbox_opcode_get(phba, mboxq),
+ psli->sli_flag, flag);
+ return -EIO;
+ }
+
+ /* Now, interrupt mode asynchrous mailbox command */
+ rc = lpfc_mbox_cmd_check(phba, mboxq);
+ if (rc) {
+ lpfc_printf_log(phba, KERN_ERR, LOG_MBOX | LOG_SLI,
+ "(%d):2543 Mailbox command x%x (x%x) "
+ "cannot issue Data: x%x x%x\n",
+ mboxq->vport ? mboxq->vport->vpi : 0,
+ mboxq->u.mb.mbxCommand,
+ lpfc_sli4_mbox_opcode_get(phba, mboxq),
+ psli->sli_flag, flag);
+ goto out_not_finished;
+ }
+ rc = lpfc_mbox_dev_check(phba);
+ if (unlikely(rc)) {
+ lpfc_printf_log(phba, KERN_ERR, LOG_MBOX | LOG_SLI,
+ "(%d):2544 Mailbox command x%x (x%x) "
+ "cannot issue Data: x%x x%x\n",
+ mboxq->vport ? mboxq->vport->vpi : 0,
+ mboxq->u.mb.mbxCommand,
+ lpfc_sli4_mbox_opcode_get(phba, mboxq),
+ psli->sli_flag, flag);
+ goto out_not_finished;
+ }
+
+ /* Put the mailbox command to the driver internal FIFO */
+ psli->slistat.mbox_busy++;
+ spin_lock_irqsave(&phba->hbalock, iflags);
+ lpfc_mbox_put(phba, mboxq);
+ spin_unlock_irqrestore(&phba->hbalock, iflags);
+ lpfc_printf_log(phba, KERN_INFO, LOG_MBOX | LOG_SLI,
+ "(%d):0354 Mbox cmd issue - Enqueue Data: "
+ "x%x (x%x) x%x x%x x%x\n",
+ mboxq->vport ? mboxq->vport->vpi : 0xffffff,
+ bf_get(lpfc_mqe_command, &mboxq->u.mqe),
+ lpfc_sli4_mbox_opcode_get(phba, mboxq),
+ phba->pport->port_state,
+ psli->sli_flag, MBX_NOWAIT);
+ /* Wake up worker thread to transport mailbox command from head */
+ lpfc_worker_wake_up(phba);
+
+ return MBX_BUSY;
+
+out_not_finished:
+ return MBX_NOT_FINISHED;
+}
+
+/**
+ * lpfc_sli4_post_async_mbox - Post an SLI4 mailbox command to device
+ * @phba: Pointer to HBA context object.
+ *
+ * This function is called by worker thread to send a mailbox command to
+ * SLI4 HBA firmware.
+ *
+ **/
+int
+lpfc_sli4_post_async_mbox(struct lpfc_hba *phba)
+{
+ struct lpfc_sli *psli = &phba->sli;
+ LPFC_MBOXQ_t *mboxq;
+ int rc = MBX_SUCCESS;
+ unsigned long iflags;
+ struct lpfc_mqe *mqe;
+ uint32_t mbx_cmnd;
+
+ /* Check interrupt mode before post async mailbox command */
+ if (unlikely(!phba->sli4_hba.intr_enable))
+ return MBX_NOT_FINISHED;
+
+ /* Check for mailbox command service token */
+ spin_lock_irqsave(&phba->hbalock, iflags);
+ if (unlikely(psli->sli_flag & LPFC_SLI_ASYNC_MBX_BLK)) {
+ spin_unlock_irqrestore(&phba->hbalock, iflags);
+ return MBX_NOT_FINISHED;
+ }
+ if (psli->sli_flag & LPFC_SLI_MBOX_ACTIVE) {
+ spin_unlock_irqrestore(&phba->hbalock, iflags);
+ return MBX_NOT_FINISHED;
+ }
+ if (unlikely(phba->sli.mbox_active)) {
+ spin_unlock_irqrestore(&phba->hbalock, iflags);
+ lpfc_printf_log(phba, KERN_ERR, LOG_MBOX | LOG_SLI,
+ "0384 There is pending active mailbox cmd\n");
+ return MBX_NOT_FINISHED;
+ }
+ /* Take the mailbox command service token */
+ psli->sli_flag |= LPFC_SLI_MBOX_ACTIVE;
+
+ /* Get the next mailbox command from head of queue */
+ mboxq = lpfc_mbox_get(phba);
+
+ /* If no more mailbox command waiting for post, we're done */
+ if (!mboxq) {
+ psli->sli_flag &= ~LPFC_SLI_MBOX_ACTIVE;
+ spin_unlock_irqrestore(&phba->hbalock, iflags);
+ return MBX_SUCCESS;
+ }
+ phba->sli.mbox_active = mboxq;
+ spin_unlock_irqrestore(&phba->hbalock, iflags);
+
+ /* Check device readiness for posting mailbox command */
+ rc = lpfc_mbox_dev_check(phba);
+ if (unlikely(rc))
+ /* Driver clean routine will clean up pending mailbox */
+ goto out_not_finished;
+
+ /* Prepare the mbox command to be posted */
+ mqe = &mboxq->u.mqe;
+ mbx_cmnd = bf_get(lpfc_mqe_command, mqe);
+
+ /* Start timer for the mbox_tmo and log some mailbox post messages */
+ mod_timer(&psli->mbox_tmo, (jiffies +
+ (HZ * lpfc_mbox_tmo_val(phba, mbx_cmnd))));
+
+ lpfc_printf_log(phba, KERN_INFO, LOG_MBOX | LOG_SLI,
+ "(%d):0355 Mailbox cmd x%x (x%x) issue Data: "
+ "x%x x%x\n",
+ mboxq->vport ? mboxq->vport->vpi : 0, mbx_cmnd,
+ lpfc_sli4_mbox_opcode_get(phba, mboxq),
+ phba->pport->port_state, psli->sli_flag);
+
+ if (mbx_cmnd != MBX_HEARTBEAT) {
+ if (mboxq->vport) {
+ lpfc_debugfs_disc_trc(mboxq->vport,
+ LPFC_DISC_TRC_MBOX_VPORT,
+ "MBOX Send vport: cmd:x%x mb:x%x x%x",
+ mbx_cmnd, mqe->un.mb_words[0],
+ mqe->un.mb_words[1]);
+ } else {
+ lpfc_debugfs_disc_trc(phba->pport,
+ LPFC_DISC_TRC_MBOX,
+ "MBOX Send: cmd:x%x mb:x%x x%x",
+ mbx_cmnd, mqe->un.mb_words[0],
+ mqe->un.mb_words[1]);
+ }
+ }
+ psli->slistat.mbox_cmd++;
+
+ /* Post the mailbox command to the port */
+ rc = lpfc_sli4_mq_put(phba->sli4_hba.mbx_wq, mqe);
+ if (rc != MBX_SUCCESS) {
+ lpfc_printf_log(phba, KERN_ERR, LOG_MBOX | LOG_SLI,
+ "(%d):2533 Mailbox command x%x (x%x) "
+ "cannot issue Data: x%x x%x\n",
+ mboxq->vport ? mboxq->vport->vpi : 0,
+ mboxq->u.mb.mbxCommand,
+ lpfc_sli4_mbox_opcode_get(phba, mboxq),
+ psli->sli_flag, MBX_NOWAIT);
+ goto out_not_finished;
+ }
+
+ return rc;
+
+out_not_finished:
+ spin_lock_irqsave(&phba->hbalock, iflags);
+ mboxq->u.mb.mbxStatus = MBX_NOT_FINISHED;
+ __lpfc_mbox_cmpl_put(phba, mboxq);
+ /* Release the token */
+ psli->sli_flag &= ~LPFC_SLI_MBOX_ACTIVE;
+ phba->sli.mbox_active = NULL;
+ spin_unlock_irqrestore(&phba->hbalock, iflags);
+
+ return MBX_NOT_FINISHED;
+}
+
+/**
+ * lpfc_sli_issue_mbox - Wrapper func for issuing mailbox command
+ * @phba: Pointer to HBA context object.
+ * @pmbox: Pointer to mailbox object.
+ * @flag: Flag indicating how the mailbox need to be processed.
+ *
+ * This routine wraps the actual SLI3 or SLI4 mailbox issuing routine from
+ * the API jump table function pointer from the lpfc_hba struct.
+ *
+ * Return codes the caller owns the mailbox command after the return of the
+ * function.
+ **/
+int
+lpfc_sli_issue_mbox(struct lpfc_hba *phba, LPFC_MBOXQ_t *pmbox, uint32_t flag)
+{
+ return phba->lpfc_sli_issue_mbox(phba, pmbox, flag);
+}
+
+/**
+ * lpfc_mbox_api_table_setup - Set up mbox api fucntion jump table
+ * @phba: The hba struct for which this call is being executed.
+ * @dev_grp: The HBA PCI-Device group number.
+ *
+ * This routine sets up the mbox interface API function jump table in @phba
+ * struct.
+ * Returns: 0 - success, -ENODEV - failure.
+ **/
+int
+lpfc_mbox_api_table_setup(struct lpfc_hba *phba, uint8_t dev_grp)
+{
+
+ switch (dev_grp) {
+ case LPFC_PCI_DEV_LP:
+ phba->lpfc_sli_issue_mbox = lpfc_sli_issue_mbox_s3;
+ phba->lpfc_sli_handle_slow_ring_event =
+ lpfc_sli_handle_slow_ring_event_s3;
+ phba->lpfc_sli_hbq_to_firmware = lpfc_sli_hbq_to_firmware_s3;
+ phba->lpfc_sli_brdrestart = lpfc_sli_brdrestart_s3;
+ phba->lpfc_sli_brdready = lpfc_sli_brdready_s3;
+ break;
+ case LPFC_PCI_DEV_OC:
+ phba->lpfc_sli_issue_mbox = lpfc_sli_issue_mbox_s4;
+ phba->lpfc_sli_handle_slow_ring_event =
+ lpfc_sli_handle_slow_ring_event_s4;
+ phba->lpfc_sli_hbq_to_firmware = lpfc_sli_hbq_to_firmware_s4;
+ phba->lpfc_sli_brdrestart = lpfc_sli_brdrestart_s4;
+ phba->lpfc_sli_brdready = lpfc_sli_brdready_s4;
+ break;
+ default:
+ lpfc_printf_log(phba, KERN_ERR, LOG_INIT,
+ "1420 Invalid HBA PCI-device group: 0x%x\n",
+ dev_grp);
+ return -ENODEV;
+ break;
+ }
+ return 0;
+}
+
+/**
* __lpfc_sli_ringtx_put - Add an iocb to the txq
* @phba: Pointer to HBA context object.
* @pring: Pointer to driver SLI ring object.
@@ -4501,28 +5629,42 @@ lpfc_sli_hba_down(struct lpfc_hba *phba)
/* Return any active mbox cmds */
del_timer_sync(&psli->mbox_tmo);
- spin_lock_irqsave(&phba->hbalock, flags);
- spin_lock(&phba->pport->work_port_lock);
+ spin_lock_irqsave(&phba->pport->work_port_lock, flags);
phba->pport->work_port_events &= ~WORKER_MBOX_TMO;
- spin_unlock(&phba->pport->work_port_lock);
+ spin_unlock_irqrestore(&phba->pport->work_port_lock, flags);
- /* Return any pending or completed mbox cmds */
- list_splice_init(&phba->sli.mboxq, &completions);
- if (psli->mbox_active) {
- list_add_tail(&psli->mbox_active->list, &completions);
- psli->mbox_active = NULL;
- psli->sli_flag &= ~LPFC_SLI_MBOX_ACTIVE;
- }
- list_splice_init(&phba->sli.mboxq_cmpl, &completions);
- spin_unlock_irqrestore(&phba->hbalock, flags);
+ return 1;
+}
+
+/**
+ * lpfc_sli4_hba_down - PCI function resource cleanup for the SLI4 HBA
+ * @phba: Pointer to HBA context object.
+ *
+ * This function cleans up all queues, iocb, buffers, mailbox commands while
+ * shutting down the SLI4 HBA FCoE function. This function is called with no
+ * lock held and always returns 1.
+ *
+ * This function does the following to cleanup driver FCoE function resources:
+ * - Free discovery resources for each virtual port
+ * - Cleanup any pending fabric iocbs
+ * - Iterate through the iocb txq and free each entry in the list.
+ * - Free up any buffer posted to the HBA.
+ * - Clean up all the queue entries: WQ, RQ, MQ, EQ, CQ, etc.
+ * - Free mailbox commands in the mailbox queue.
+ **/
+int
+lpfc_sli4_hba_down(struct lpfc_hba *phba)
+{
+ /* Stop the SLI4 device port */
+ lpfc_stop_port(phba);
+
+ /* Tear down the queues in the HBA */
+ lpfc_sli4_queue_unset(phba);
+
+ /* unregister default FCFI from the HBA */
+ lpfc_sli4_fcfi_unreg(phba, phba->fcf.fcfi);
- while (!list_empty(&completions)) {
- list_remove_head(&completions, pmb, LPFC_MBOXQ_t, list);
- pmb->mb.mbxStatus = MBX_NOT_FINISHED;
- if (pmb->mbox_cmpl)
- pmb->mbox_cmpl(phba,pmb);
- }
return 1;
}
@@ -4853,7 +5995,10 @@ lpfc_sli_issue_abort_iotag(struct lpfc_h
iabt = &abtsiocbp->iocb;
iabt->un.acxri.abortType = ABORT_TYPE_ABTS;
iabt->un.acxri.abortContextTag = icmd->ulpContext;
- iabt->un.acxri.abortIoTag = icmd->ulpIoTag;
+ if (phba->sli_rev == LPFC_SLI_REV4)
+ iabt->un.acxri.abortIoTag = cmdiocb->sli4_xritag;
+ else
+ iabt->un.acxri.abortIoTag = icmd->ulpIoTag;
iabt->ulpLe = 1;
iabt->ulpClass = icmd->ulpClass;
@@ -4869,7 +6014,7 @@ lpfc_sli_issue_abort_iotag(struct lpfc_h
"abort cmd iotag x%x\n",
iabt->un.acxri.abortContextTag,
iabt->un.acxri.abortIoTag, abtsiocbp->iotag);
- retval = __lpfc_sli_issue_iocb(phba, pring, abtsiocbp, 0);
+ retval = __lpfc_sli_issue_iocb(phba, pring->ringno, abtsiocbp, 0);
if (retval)
__lpfc_sli_release_iocbq(phba, abtsiocbp);
@@ -5052,7 +6197,10 @@ lpfc_sli_abort_iocb(struct lpfc_vport *v
cmd = &iocbq->iocb;
abtsiocb->iocb.un.acxri.abortType = ABORT_TYPE_ABTS;
abtsiocb->iocb.un.acxri.abortContextTag = cmd->ulpContext;
- abtsiocb->iocb.un.acxri.abortIoTag = cmd->ulpIoTag;
+ if (phba->sli_rev == LPFC_SLI_REV4)
+ abtsiocb->iocb.un.acxri.abortIoTag = iocbq->sli4_xritag;
+ else
+ abtsiocb->iocb.un.acxri.abortIoTag = cmd->ulpIoTag;
abtsiocb->iocb.ulpLe = 1;
abtsiocb->iocb.ulpClass = cmd->ulpClass;
abtsiocb->vport = phba->pport;
@@ -5064,7 +6212,8 @@ lpfc_sli_abort_iocb(struct lpfc_vport *v
/* Setup callback routine and issue the command. */
abtsiocb->iocb_cmpl = lpfc_sli_abort_fcp_cmpl;
- ret_val = lpfc_sli_issue_iocb(phba, pring, abtsiocb, 0);
+ ret_val = lpfc_sli_issue_iocb(phba, pring->ringno,
+ abtsiocb, 0);
if (ret_val == IOCB_ERROR) {
lpfc_sli_release_iocbq(phba, abtsiocb);
errcnt++;
@@ -5145,7 +6294,7 @@ lpfc_sli_wake_iocb_wait(struct lpfc_hba
**/
int
lpfc_sli_issue_iocb_wait(struct lpfc_hba *phba,
- struct lpfc_sli_ring *pring,
+ uint32_t ring_number,
struct lpfc_iocbq *piocb,
struct lpfc_iocbq *prspiocbq,
uint32_t timeout)
@@ -5176,7 +6325,7 @@ lpfc_sli_issue_iocb_wait(struct lpfc_hba
readl(phba->HCregaddr); /* flush */
}
- retval = lpfc_sli_issue_iocb(phba, pring, piocb, 0);
+ retval = lpfc_sli_issue_iocb(phba, ring_number, piocb, 0);
if (retval == IOCB_SUCCESS) {
timeout_req = timeout * HZ;
timeleft = wait_event_timeout(done_q,
@@ -5385,6 +6534,58 @@ lpfc_sli_eratt_read(struct lpfc_hba *phb
}
/**
+ * lpfc_sli4_eratt_read - read sli-4 error attention events
+ * @phba: Pointer to HBA context.
+ *
+ * This function is called to read the SLI4 device error attention registers
+ * for possible error attention events. The caller must hold the hostlock
+ * with spin_lock_irq().
+ *
+ * This fucntion returns 1 when there is Error Attention in the Host Attention
+ * Register and returns 0 otherwise.
+ **/
+static int
+lpfc_sli4_eratt_read(struct lpfc_hba *phba)
+{
+ uint32_t uerr_sta_hi, uerr_sta_lo;
+ uint32_t onlnreg0, onlnreg1;
+
+ /* For now, use the SLI4 device internal unrecoverable error
+ * registers for error attention. This can be changed later.
+ */
+ onlnreg0 = readl(phba->sli4_hba.ONLINE0regaddr);
+ onlnreg1 = readl(phba->sli4_hba.ONLINE1regaddr);
+ if ((onlnreg0 != LPFC_ONLINE_NERR) || (onlnreg1 != LPFC_ONLINE_NERR)) {
+ uerr_sta_lo = readl(phba->sli4_hba.UERRLOregaddr);
+ uerr_sta_hi = readl(phba->sli4_hba.UERRHIregaddr);
+ if (uerr_sta_lo || uerr_sta_hi) {
+ lpfc_printf_log(phba, KERN_ERR, LOG_INIT,
+ "1423 HBA Unrecoverable error: "
+ "uerr_lo_reg=0x%x, uerr_hi_reg=0x%x, "
+ "online0_reg=0x%x, online1_reg=0x%x\n",
+ uerr_sta_lo, uerr_sta_hi,
+ onlnreg0, onlnreg1);
+ /* TEMP: as the driver error recover logic is not
+ * fully developed, we just log the error message
+ * and the device error attention action is now
+ * temporarily disabled.
+ */
+ return 0;
+ phba->work_status[0] = uerr_sta_lo;
+ phba->work_status[1] = uerr_sta_hi;
+ spin_lock_irq(&phba->hbalock);
+ /* Set the driver HA work bitmap */
+ phba->work_ha |= HA_ERATT;
+ /* Indicate polling handles this ERATT */
+ phba->hba_flag |= HBA_ERATT_HANDLED;
+ spin_unlock_irq(&phba->hbalock);
+ return 1;
+ }
+ }
+ return 0;
+}
+
+/**
* lpfc_sli_check_eratt - check error attention events
* @phba: Pointer to HBA context.
*
@@ -5434,6 +6635,10 @@ lpfc_sli_check_eratt(struct lpfc_hba *ph
/* Read chip Host Attention (HA) register */
ha_copy = lpfc_sli_eratt_read(phba);
break;
+ case LPFC_SLI_REV4:
+ /* Read devcie Uncoverable Error (UERR) registers */
+ ha_copy = lpfc_sli4_eratt_read(phba);
+ break;
default:
lpfc_printf_log(phba, KERN_ERR, LOG_INIT,
"0299 Invalid SLI revision (%d)\n",
diff -upNr a/drivers/scsi/lpfc/lpfc_sli.h b/drivers/scsi/lpfc/lpfc_sli.h
--- a/drivers/scsi/lpfc/lpfc_sli.h 2008-10-18 10:32:52.000000000 -0400
+++ b/drivers/scsi/lpfc/lpfc_sli.h 2009-05-22 13:16:40.000000000 -0400
@@ -29,13 +29,23 @@ typedef enum _lpfc_ctx_cmd {
LPFC_CTX_HOST
} lpfc_ctx_cmd;
+/* This structure is used to carry the needed response IOCB states */
+struct lpfc_sli4_rspiocb_info {
+ uint8_t hw_status;
+ uint8_t bfield;
+#define LPFC_XB 0x1
+#define LPFC_PV 0x2
+ uint8_t priority;
+ uint8_t reserved;
+};
+
/* This structure is used to handle IOCB requests / responses */
struct lpfc_iocbq {
/* lpfc_iocbqs are used in double linked lists */
struct list_head list;
struct list_head clist;
uint16_t iotag; /* pre-assigned IO tag */
- uint16_t rsvd1;
+ uint16_t sli4_xritag; /* pre-assigned XRI, (OXID) tag. */
IOCB_t iocb; /* IOCB cmd */
uint8_t retry; /* retry counter for IOCB cmd - if needed */
@@ -65,7 +75,7 @@ struct lpfc_iocbq {
struct lpfc_iocbq *);
void (*iocb_cmpl) (struct lpfc_hba *, struct lpfc_iocbq *,
struct lpfc_iocbq *);
-
+ struct lpfc_sli4_rspiocb_info sli4_info;
};
#define SLI_IOCB_RET_IOCB 1 /* Return IOCB if cmd ring full */
@@ -81,14 +91,18 @@ struct lpfc_iocbq {
typedef struct lpfcMboxq {
/* MBOXQs are used in single linked lists */
struct list_head list; /* ptr to next mailbox command */
- MAILBOX_t mb; /* Mailbox cmd */
- struct lpfc_vport *vport;/* virutal port pointer */
+ union {
+ MAILBOX_t mb; /* Mailbox cmd */
+ struct lpfc_mqe mqe;
+ } u;
+ struct lpfc_vport *vport;/* virtual port pointer */
void *context1; /* caller context information */
void *context2; /* caller context information */
void (*mbox_cmpl) (struct lpfc_hba *, struct lpfcMboxq *);
uint8_t mbox_flag;
-
+ struct lpfc_mcqe mcqe;
+ struct lpfc_mbx_nembed_sge_virt *sge_array;
} LPFC_MBOXQ_t;
#define MBX_POLL 1 /* poll mailbox till command done, then
@@ -234,6 +248,7 @@ struct lpfc_sli {
#define LPFC_PROCESS_LA 0x400 /* Able to process link attention */
#define LPFC_BLOCK_MGMT_IO 0x800 /* Don't allow mgmt mbx or iocb cmds */
#define LPFC_MENLO_MAINT 0x1000 /* need for menl fw download */
+#define LPFC_SLI_ASYNC_MBX_BLK 0x2000 /* Async mailbox is blocked */
struct lpfc_sli_ring ring[LPFC_MAX_RING];
int fcp_ring; /* ring used for FCP initiator commands */
@@ -261,6 +276,8 @@ struct lpfc_sli {
#define LPFC_MBOX_TMO 30 /* Sec tmo for outstanding mbox
command */
+#define LPFC_MBOX_SLI4_CONFIG_TMO 60 /* Sec tmo for outstanding mbox
+ command */
#define LPFC_MBOX_TMO_FLASH_CMD 300 /* Sec tmo for outstanding FLASH write
* or erase cmds. This is especially
* long because of the potential of
diff -upNr a/drivers/scsi/lpfc/lpfc_vport.c b/drivers/scsi/lpfc/lpfc_vport.c
--- a/drivers/scsi/lpfc/lpfc_vport.c 2009-05-19 09:39:28.000000000 -0400
+++ b/drivers/scsi/lpfc/lpfc_vport.c 2009-05-22 13:16:40.000000000 -0400
@@ -32,8 +32,10 @@
#include <scsi/scsi_device.h>
#include <scsi/scsi_host.h>
#include <scsi/scsi_transport_fc.h>
+#include "lpfc_hw4.h"
#include "lpfc_hw.h"
#include "lpfc_sli.h"
+#include "lpfc_sli4.h"
#include "lpfc_nl.h"
#include "lpfc_disc.h"
#include "lpfc_scsi.h"
@@ -89,6 +91,8 @@ lpfc_alloc_vpi(struct lpfc_hba *phba)
vpi = 0;
else
set_bit(vpi, phba->vpi_bmask);
+ if (phba->sli_rev == LPFC_SLI_REV4)
+ phba->sli4_hba.max_cfg_param.vpi_used++;
spin_unlock_irq(&phba->hbalock);
return vpi;
}
@@ -96,8 +100,12 @@ lpfc_alloc_vpi(struct lpfc_hba *phba)
static void
lpfc_free_vpi(struct lpfc_hba *phba, int vpi)
{
+ if (vpi == 0)
+ return;
spin_lock_irq(&phba->hbalock);
clear_bit(vpi, phba->vpi_bmask);
+ if (phba->sli_rev == LPFC_SLI_REV4)
+ phba->sli4_hba.max_cfg_param.vpi_used--;
spin_unlock_irq(&phba->hbalock);
}
@@ -308,6 +316,21 @@ lpfc_vport_create(struct fc_vport *fc_vp
goto error_out;
}
+ /*
+ * In SLI4, the vpi must be activated before it can be used
+ * by the port.
+ */
+ if (phba->sli_rev == LPFC_SLI_REV4) {
+ rc = lpfc_sli4_init_vpi(phba, vpi);
+ if (rc) {
+ lpfc_printf_log(phba, KERN_ERR, LOG_VPORT,
+ "1838 Failed to INIT_VPI on vpi %d "
+ "status %d\n", vpi, rc);
+ rc = VPORT_NORESOURCES;
+ lpfc_free_vpi(phba, vpi);
+ goto error_out;
+ }
+ }
/* Assign an unused board number */
if ((instance = lpfc_get_instance()) < 0) {
reply other threads:[~2009-05-22 18:52 UTC|newest]
Thread overview: [no followups] expand[flat|nested] mbox.gz Atom feed
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1243018319.7729.49.camel@ogier \
--to=james.smart@emulex.com \
--cc=linux-scsi@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.