From: Stefani Seibold <stefani@seibold.net>
To: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Matthew Wilcox <matthew@wil.cx>,
linux-kernel <linux-kernel@vger.kernel.org>,
Linux PCI <linux-pci@vger.kernel.org>,
Jesse Barnes <jbarnes@virtuousgeek.org>,
"Rafael J. Wysocki" <rjw@sisk.pl>
Subject: Re: PCI Express-to-PCI Bridge: yenta_cardbus no bus associated!
Date: Mon, 26 Oct 2009 08:27:53 +0100 [thread overview]
Message-ID: <1256542073.4187.14.camel@wall-e> (raw)
In-Reply-To: <20091025083841.GA12526@isilmar.linta.de>
> >
> > Okay, i tried it again with 'pci=assign-bussed'. All i get is a
> >
> > decode_hpp: Could not get hotplug parameters. Use defaults
> >
> > thats all. The express-card will not be detected.
>
> I assume the "d" at the end was just a typo -- and "lspci -vvv" looks the
> same?
>
Yes, this was a typo. Here are the diff's of dmesg and lspci -vvv with
and without "pci=assign-busses" after inserting the express card.
dmesg without 'pci=assign-busses':
----------------------------------
pci 0000:0e:00.0: supports D1 D2
pci 0000:0f:00.0: reg 10 32bit mmio: [0x000000-0x000fff]
pci 0000:0f:00.0: supports D1 D2
pci 0000:0f:00.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:0f:00.0: PME# disabled
pci 0000:0e:00.0: bridge io port: [0x00-0xfff]
pci 0000:0e:00.0: bridge 32bit mmio: [0x000000-0x0fffff]
pci 0000:0e:00.0: bridge 64bit mmio pref: [0x000000-0x0fffff]
ACPI: Delete PCI Interrupt Routing Table for 0000:0f
pci 0000:0e:00.0: PCI bridge, secondary bus 0000:0f
pci 0000:0e:00.0: IO window: disabled
pci 0000:0e:00.0: MEM window: 0xf1c00000-0xf1cfffff
pci 0000:0e:00.0: PREFETCH window: disabled
decode_hpp: Could not get hotplug parameters. Use defaults
pci 0000:0e:00.0: enabling device (0000 -> 0002)
pci 0000:0e:00.0: setting latency timer to 64
yenta_cardbus 0000:0f:00.0: no bus associated! (try 'pci=assign-busses')
CE: hpet increasing min_delta_ns to 50624 nsec
lspci -vvv without 'pci=assign-busses':
---------------------------------------
0e:00.0 PCI bridge: Texas Instruments XIO2000(A)/XIO2200(A) PCI Express-to-PCI Bridge (rev 03) (prog-if 00 [Normal decode])
Physical Slot: 1
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=0e, secondary=0f, subordinate=0f, sec-latency=64
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: f1c00000-f1cfffff
Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Bridge: PM- B3+
Capabilities: [60] MSI: Enable- Count=1/16 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [80] Subsystem: Device 5678:1234
Capabilities: [90] Express (v1) PCI/PCI-X Bridge, MSI 00
DevCap: MaxPayload 512 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE- FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+ BrConfRtry-
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- UncorrErr+ FatalErr- UnsuppReq- AuxPwr+ TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <64ns, L1 <1us
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
Capabilities: [100] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
AERCap: First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn-
0f:00.0 CardBus bridge: Texas Instruments PCIxx12 Cardbus Controller
Subsystem: Texas Instruments Device ac48
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 255
Region 0: Memory at f1c00000 (32-bit, non-prefetchable) [disabled] [size=4K]
Bus: primary=00, secondary=00, subordinate=00, sec-latency=0
Memory window 0: 00000000-00000000 [disabled] (prefetchable)
Memory window 1: 00000000-00000000 [disabled] (prefetchable)
I/O window 0: 00000000-00000003 [disabled]
I/O window 1: 00000000-00000003 [disabled]
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt- PostWrite-
16-bit legacy interface ports at 0001
dmesg with 'pci=assign-busses':
-------------------------------
pci 0000:05:00.0: supports D1 D2
decode_hpp: Could not get hotplug parameters. Use defaults
lspci -vvv with 'pci=assign-busses':
------------------------------------
05:00.0 PCI bridge: Texas Instruments XIO2000(A)/XIO2200(A) PCI Express-to-PCI Bridge (rev 03) (prog-if 00 [Normal decode])
Physical Slot: 1
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Bus: primary=00, secondary=00, subordinate=00, sec-latency=64
I/O behind bridge: 00000000-00000fff
Memory behind bridge: 00000000-000fffff
Prefetchable memory behind bridge: 0000000000000000-00000000000fffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Bridge: PM- B3+
Capabilities: [60] MSI: Enable- Count=1/16 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [80] Subsystem: Device 5678:1234
Capabilities: [90] Express (v1) PCI/PCI-X Bridge, MSI 00
DevCap: MaxPayload 512 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE- FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+ BrConfRtry-
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <64ns, L1 <1us
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
Capabilities: [100] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
AERCap: First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn-
Greetings,
Stefani
prev parent reply other threads:[~2009-10-26 7:28 UTC|newest]
Thread overview: 7+ messages / expand[flat|nested] mbox.gz Atom feed top
2009-09-29 18:23 PCI Express-to-PCI Bridge: yenta_cardbus no bus associated! Stefani Seibold
2009-09-29 23:15 ` Rafael J. Wysocki
2009-10-24 14:03 ` Stefani Seibold
2009-10-24 20:34 ` Matthew Wilcox
2009-10-25 8:10 ` Stefani Seibold
2009-10-25 8:38 ` Dominik Brodowski
2009-10-26 7:27 ` Stefani Seibold [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1256542073.4187.14.camel@wall-e \
--to=stefani@seibold.net \
--cc=jbarnes@virtuousgeek.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-pci@vger.kernel.org \
--cc=linux@dominikbrodowski.net \
--cc=matthew@wil.cx \
--cc=rjw@sisk.pl \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.