From: Gregory Bean <gbean@codeaurora.org>
To: dwalker@codeaurora.org
Cc: linux-arm-msm@vger.kernel.org, linux-kernel@vger.kernel.org,
Gregory Bean <gbean@codeaurora.org>
Subject: [PATCH 1/3 v2] msm: Add gpio register address mapping information.
Date: Sat, 19 Jun 2010 09:29:02 -0700 [thread overview]
Message-ID: <1276964944-11063-2-git-send-email-gbean@codeaurora.org> (raw)
In-Reply-To: <1276964944-11063-1-git-send-email-gbean@codeaurora.org>
Add tables containing iomap information for gpio registers
on all supported MSM7x and QSD8x targets.
Signed-off-by: Gregory Bean <gbean@codeaurora.org>
---
arch/arm/mach-msm/gpio_hw-7x30.h | 112 ++++++++++++++++++++++++++++++++++++++
arch/arm/mach-msm/gpio_hw-7xxx.h | 97 +++++++++++++++++++++++++++++++++
arch/arm/mach-msm/gpio_hw-8x50.h | 112 ++++++++++++++++++++++++++++++++++++++
arch/arm/mach-msm/gpio_hw.h | 35 ++++++++++++
4 files changed, 356 insertions(+), 0 deletions(-)
create mode 100644 arch/arm/mach-msm/gpio_hw-7x30.h
create mode 100644 arch/arm/mach-msm/gpio_hw-7xxx.h
create mode 100644 arch/arm/mach-msm/gpio_hw-8x50.h
create mode 100644 arch/arm/mach-msm/gpio_hw.h
diff --git a/arch/arm/mach-msm/gpio_hw-7x30.h b/arch/arm/mach-msm/gpio_hw-7x30.h
new file mode 100644
index 0000000..cedd465
--- /dev/null
+++ b/arch/arm/mach-msm/gpio_hw-7x30.h
@@ -0,0 +1,112 @@
+/* Copyright (c) 2010, Code Aurora Forum. All rights reserved.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are
+ * met:
+ * * Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * * Redistributions in binary form must reproduce the above
+ * copyright notice, this list of conditions and the following
+ * disclaimer in the documentation and/or other materials provided
+ * with the distribution.
+ * * Neither the name of Code Aurora Forum, Inc. nor the names of its
+ * contributors may be used to endorse or promote products derived
+ * from this software without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED "AS IS" AND ANY EXPRESS OR IMPLIED
+ * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
+ * MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT
+ * ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS
+ * BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
+ * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
+ * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR
+ * BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY,
+ * WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE
+ * OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN
+ * IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ *
+ */
+#ifndef __ARCH_ARM_MACH_MSM_GPIO_HW_7X30_H
+#define __ARCH_ARM_MACH_MSM_GPIO_HW_7X30_H
+
+/* output value */
+#define GPIO_OUT_0 GPIO1_REG(0x00) /* gpio 15-0 */
+#define GPIO_OUT_1 GPIO2_REG(0x00) /* gpio 43-16 */
+#define GPIO_OUT_2 GPIO1_REG(0x04) /* gpio 67-44 */
+#define GPIO_OUT_3 GPIO1_REG(0x08) /* gpio 94-68 */
+#define GPIO_OUT_4 GPIO1_REG(0x0C) /* gpio 106-95 */
+#define GPIO_OUT_5 GPIO1_REG(0x50) /* gpio 133-107 */
+#define GPIO_OUT_6 GPIO1_REG(0xC4) /* gpio 150-134 */
+#define GPIO_OUT_7 GPIO1_REG(0x214) /* gpio 181-151 */
+
+/* same pin map as above, output enable */
+#define GPIO_OE_0 GPIO1_REG(0x10)
+#define GPIO_OE_1 GPIO2_REG(0x08)
+#define GPIO_OE_2 GPIO1_REG(0x14)
+#define GPIO_OE_3 GPIO1_REG(0x18)
+#define GPIO_OE_4 GPIO1_REG(0x1C)
+#define GPIO_OE_5 GPIO1_REG(0x54)
+#define GPIO_OE_6 GPIO1_REG(0xC8)
+#define GPIO_OE_7 GPIO1_REG(0x218)
+
+/* same pin map as above, input read */
+#define GPIO_IN_0 GPIO1_REG(0x34)
+#define GPIO_IN_1 GPIO2_REG(0x20)
+#define GPIO_IN_2 GPIO1_REG(0x38)
+#define GPIO_IN_3 GPIO1_REG(0x3C)
+#define GPIO_IN_4 GPIO1_REG(0x40)
+#define GPIO_IN_5 GPIO1_REG(0x44)
+#define GPIO_IN_6 GPIO1_REG(0xCC)
+#define GPIO_IN_7 GPIO1_REG(0x21C)
+
+/* same pin map as above, 1=edge 0=level interrupt */
+#define GPIO_INT_EDGE_0 GPIO1_REG(0x60)
+#define GPIO_INT_EDGE_1 GPIO2_REG(0x50)
+#define GPIO_INT_EDGE_2 GPIO1_REG(0x64)
+#define GPIO_INT_EDGE_3 GPIO1_REG(0x68)
+#define GPIO_INT_EDGE_4 GPIO1_REG(0x6C)
+#define GPIO_INT_EDGE_5 GPIO1_REG(0xC0)
+#define GPIO_INT_EDGE_6 GPIO1_REG(0xD0)
+#define GPIO_INT_EDGE_7 GPIO1_REG(0x240)
+
+/* same pin map as above, 1=positive 0=negative */
+#define GPIO_INT_POS_0 GPIO1_REG(0x70)
+#define GPIO_INT_POS_1 GPIO2_REG(0x58)
+#define GPIO_INT_POS_2 GPIO1_REG(0x74)
+#define GPIO_INT_POS_3 GPIO1_REG(0x78)
+#define GPIO_INT_POS_4 GPIO1_REG(0x7C)
+#define GPIO_INT_POS_5 GPIO1_REG(0xBC)
+#define GPIO_INT_POS_6 GPIO1_REG(0xD4)
+#define GPIO_INT_POS_7 GPIO1_REG(0x228)
+
+/* same pin map as above, interrupt enable */
+#define GPIO_INT_EN_0 GPIO1_REG(0x80)
+#define GPIO_INT_EN_1 GPIO2_REG(0x60)
+#define GPIO_INT_EN_2 GPIO1_REG(0x84)
+#define GPIO_INT_EN_3 GPIO1_REG(0x88)
+#define GPIO_INT_EN_4 GPIO1_REG(0x8C)
+#define GPIO_INT_EN_5 GPIO1_REG(0xB8)
+#define GPIO_INT_EN_6 GPIO1_REG(0xD8)
+#define GPIO_INT_EN_7 GPIO1_REG(0x22C)
+
+/* same pin map as above, write 1 to clear interrupt */
+#define GPIO_INT_CLEAR_0 GPIO1_REG(0x90)
+#define GPIO_INT_CLEAR_1 GPIO2_REG(0x68)
+#define GPIO_INT_CLEAR_2 GPIO1_REG(0x94)
+#define GPIO_INT_CLEAR_3 GPIO1_REG(0x98)
+#define GPIO_INT_CLEAR_4 GPIO1_REG(0x9C)
+#define GPIO_INT_CLEAR_5 GPIO1_REG(0xB4)
+#define GPIO_INT_CLEAR_6 GPIO1_REG(0xDC)
+#define GPIO_INT_CLEAR_7 GPIO1_REG(0x230)
+
+/* same pin map as above, 1=interrupt pending */
+#define GPIO_INT_STATUS_0 GPIO1_REG(0xA0)
+#define GPIO_INT_STATUS_1 GPIO2_REG(0x70)
+#define GPIO_INT_STATUS_2 GPIO1_REG(0xA4)
+#define GPIO_INT_STATUS_3 GPIO1_REG(0xA8)
+#define GPIO_INT_STATUS_4 GPIO1_REG(0xAC)
+#define GPIO_INT_STATUS_5 GPIO1_REG(0xB0)
+#define GPIO_INT_STATUS_6 GPIO1_REG(0xE0)
+#define GPIO_INT_STATUS_7 GPIO1_REG(0x234)
+
+#endif
diff --git a/arch/arm/mach-msm/gpio_hw-7xxx.h b/arch/arm/mach-msm/gpio_hw-7xxx.h
new file mode 100644
index 0000000..7bfd812
--- /dev/null
+++ b/arch/arm/mach-msm/gpio_hw-7xxx.h
@@ -0,0 +1,97 @@
+/* Copyright (c) 2007, Google, Inc.
+ * Copyright (c) 2010, Code Aurora Forum. All rights reserved.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are
+ * met:
+ * * Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * * Redistributions in binary form must reproduce the above
+ * copyright notice, this list of conditions and the following
+ * disclaimer in the documentation and/or other materials provided
+ * with the distribution.
+ * * Neither the name of Code Aurora Forum, Inc. nor the names of its
+ * contributors may be used to endorse or promote products derived
+ * from this software without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED "AS IS" AND ANY EXPRESS OR IMPLIED
+ * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
+ * MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT
+ * ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS
+ * BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
+ * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
+ * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR
+ * BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY,
+ * WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE
+ * OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN
+ * IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ *
+ */
+#ifndef __ARCH_ARM_MACH_MSM_GPIO_HW_7XXX_H
+#define __ARCH_ARM_MACH_MSM_GPIO_HW_7XXX_H
+
+/* output value */
+#define GPIO_OUT_0 GPIO1_REG(0x00) /* gpio 15-0 */
+#define GPIO_OUT_1 GPIO2_REG(0x00) /* gpio 42-16 */
+#define GPIO_OUT_2 GPIO1_REG(0x04) /* gpio 67-43 */
+#define GPIO_OUT_3 GPIO1_REG(0x08) /* gpio 94-68 */
+#define GPIO_OUT_4 GPIO1_REG(0x0C) /* gpio 106-95 */
+#define GPIO_OUT_5 GPIO1_REG(0x50) /* gpio 107-121 */
+
+/* same pin map as above, output enable */
+#define GPIO_OE_0 GPIO1_REG(0x10)
+#define GPIO_OE_1 GPIO2_REG(0x08)
+#define GPIO_OE_2 GPIO1_REG(0x14)
+#define GPIO_OE_3 GPIO1_REG(0x18)
+#define GPIO_OE_4 GPIO1_REG(0x1C)
+#define GPIO_OE_5 GPIO1_REG(0x54)
+
+/* same pin map as above, input read */
+#define GPIO_IN_0 GPIO1_REG(0x34)
+#define GPIO_IN_1 GPIO2_REG(0x20)
+#define GPIO_IN_2 GPIO1_REG(0x38)
+#define GPIO_IN_3 GPIO1_REG(0x3C)
+#define GPIO_IN_4 GPIO1_REG(0x40)
+#define GPIO_IN_5 GPIO1_REG(0x44)
+
+/* same pin map as above, 1=edge 0=level interrupt */
+#define GPIO_INT_EDGE_0 GPIO1_REG(0x60)
+#define GPIO_INT_EDGE_1 GPIO2_REG(0x50)
+#define GPIO_INT_EDGE_2 GPIO1_REG(0x64)
+#define GPIO_INT_EDGE_3 GPIO1_REG(0x68)
+#define GPIO_INT_EDGE_4 GPIO1_REG(0x6C)
+#define GPIO_INT_EDGE_5 GPIO1_REG(0xC0)
+
+/* same pin map as above, 1=positive 0=negative */
+#define GPIO_INT_POS_0 GPIO1_REG(0x70)
+#define GPIO_INT_POS_1 GPIO2_REG(0x58)
+#define GPIO_INT_POS_2 GPIO1_REG(0x74)
+#define GPIO_INT_POS_3 GPIO1_REG(0x78)
+#define GPIO_INT_POS_4 GPIO1_REG(0x7C)
+#define GPIO_INT_POS_5 GPIO1_REG(0xBC)
+
+/* same pin map as above, interrupt enable */
+#define GPIO_INT_EN_0 GPIO1_REG(0x80)
+#define GPIO_INT_EN_1 GPIO2_REG(0x60)
+#define GPIO_INT_EN_2 GPIO1_REG(0x84)
+#define GPIO_INT_EN_3 GPIO1_REG(0x88)
+#define GPIO_INT_EN_4 GPIO1_REG(0x8C)
+#define GPIO_INT_EN_5 GPIO1_REG(0xB8)
+
+/* same pin map as above, write 1 to clear interrupt */
+#define GPIO_INT_CLEAR_0 GPIO1_REG(0x90)
+#define GPIO_INT_CLEAR_1 GPIO2_REG(0x68)
+#define GPIO_INT_CLEAR_2 GPIO1_REG(0x94)
+#define GPIO_INT_CLEAR_3 GPIO1_REG(0x98)
+#define GPIO_INT_CLEAR_4 GPIO1_REG(0x9C)
+#define GPIO_INT_CLEAR_5 GPIO1_REG(0xB4)
+
+/* same pin map as above, 1=interrupt pending */
+#define GPIO_INT_STATUS_0 GPIO1_REG(0xA0)
+#define GPIO_INT_STATUS_1 GPIO2_REG(0x70)
+#define GPIO_INT_STATUS_2 GPIO1_REG(0xA4)
+#define GPIO_INT_STATUS_3 GPIO1_REG(0xA8)
+#define GPIO_INT_STATUS_4 GPIO1_REG(0xAC)
+#define GPIO_INT_STATUS_5 GPIO1_REG(0xB0)
+
+#endif
diff --git a/arch/arm/mach-msm/gpio_hw-8x50.h b/arch/arm/mach-msm/gpio_hw-8x50.h
new file mode 100644
index 0000000..9009f58
--- /dev/null
+++ b/arch/arm/mach-msm/gpio_hw-8x50.h
@@ -0,0 +1,112 @@
+/* Copyright (c) 2010, Code Aurora Forum. All rights reserved.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are
+ * met:
+ * * Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * * Redistributions in binary form must reproduce the above
+ * copyright notice, this list of conditions and the following
+ * disclaimer in the documentation and/or other materials provided
+ * with the distribution.
+ * * Neither the name of Code Aurora Forum, Inc. nor the names of its
+ * contributors may be used to endorse or promote products derived
+ * from this software without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED "AS IS" AND ANY EXPRESS OR IMPLIED
+ * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
+ * MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT
+ * ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS
+ * BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
+ * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
+ * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR
+ * BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY,
+ * WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE
+ * OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN
+ * IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ *
+ */
+#ifndef __ARCH_ARM_MACH_MSM_GPIO_HW_8X50_H
+#define __ARCH_ARM_MACH_MSM_GPIO_HW_8X50_H
+
+/* output value */
+#define GPIO_OUT_0 GPIO1_REG(0x00) /* gpio 15-0 */
+#define GPIO_OUT_1 GPIO2_REG(0x00) /* gpio 42-16 */
+#define GPIO_OUT_2 GPIO1_REG(0x04) /* gpio 67-43 */
+#define GPIO_OUT_3 GPIO1_REG(0x08) /* gpio 94-68 */
+#define GPIO_OUT_4 GPIO1_REG(0x0C) /* gpio 103-95 */
+#define GPIO_OUT_5 GPIO1_REG(0x10) /* gpio 121-104 */
+#define GPIO_OUT_6 GPIO1_REG(0x14) /* gpio 152-122 */
+#define GPIO_OUT_7 GPIO1_REG(0x18) /* gpio 164-153 */
+
+/* same pin map as above, output enable */
+#define GPIO_OE_0 GPIO1_REG(0x20)
+#define GPIO_OE_1 GPIO2_REG(0x08)
+#define GPIO_OE_2 GPIO1_REG(0x24)
+#define GPIO_OE_3 GPIO1_REG(0x28)
+#define GPIO_OE_4 GPIO1_REG(0x2C)
+#define GPIO_OE_5 GPIO1_REG(0x30)
+#define GPIO_OE_6 GPIO1_REG(0x34)
+#define GPIO_OE_7 GPIO1_REG(0x38)
+
+/* same pin map as above, input read */
+#define GPIO_IN_0 GPIO1_REG(0x50)
+#define GPIO_IN_1 GPIO2_REG(0x20)
+#define GPIO_IN_2 GPIO1_REG(0x54)
+#define GPIO_IN_3 GPIO1_REG(0x58)
+#define GPIO_IN_4 GPIO1_REG(0x5C)
+#define GPIO_IN_5 GPIO1_REG(0x60)
+#define GPIO_IN_6 GPIO1_REG(0x64)
+#define GPIO_IN_7 GPIO1_REG(0x68)
+
+/* same pin map as above, 1=edge 0=level interrupt */
+#define GPIO_INT_EDGE_0 GPIO1_REG(0x70)
+#define GPIO_INT_EDGE_1 GPIO2_REG(0x50)
+#define GPIO_INT_EDGE_2 GPIO1_REG(0x74)
+#define GPIO_INT_EDGE_3 GPIO1_REG(0x78)
+#define GPIO_INT_EDGE_4 GPIO1_REG(0x7C)
+#define GPIO_INT_EDGE_5 GPIO1_REG(0x80)
+#define GPIO_INT_EDGE_6 GPIO1_REG(0x84)
+#define GPIO_INT_EDGE_7 GPIO1_REG(0x88)
+
+/* same pin map as above, 1=positive 0=negative */
+#define GPIO_INT_POS_0 GPIO1_REG(0x90)
+#define GPIO_INT_POS_1 GPIO2_REG(0x58)
+#define GPIO_INT_POS_2 GPIO1_REG(0x94)
+#define GPIO_INT_POS_3 GPIO1_REG(0x98)
+#define GPIO_INT_POS_4 GPIO1_REG(0x9C)
+#define GPIO_INT_POS_5 GPIO1_REG(0xA0)
+#define GPIO_INT_POS_6 GPIO1_REG(0xA4)
+#define GPIO_INT_POS_7 GPIO1_REG(0xA8)
+
+/* same pin map as above, interrupt enable */
+#define GPIO_INT_EN_0 GPIO1_REG(0xB0)
+#define GPIO_INT_EN_1 GPIO2_REG(0x60)
+#define GPIO_INT_EN_2 GPIO1_REG(0xB4)
+#define GPIO_INT_EN_3 GPIO1_REG(0xB8)
+#define GPIO_INT_EN_4 GPIO1_REG(0xBC)
+#define GPIO_INT_EN_5 GPIO1_REG(0xC0)
+#define GPIO_INT_EN_6 GPIO1_REG(0xC4)
+#define GPIO_INT_EN_7 GPIO1_REG(0xC8)
+
+/* same pin map as above, write 1 to clear interrupt */
+#define GPIO_INT_CLEAR_0 GPIO1_REG(0xD0)
+#define GPIO_INT_CLEAR_1 GPIO2_REG(0x68)
+#define GPIO_INT_CLEAR_2 GPIO1_REG(0xD4)
+#define GPIO_INT_CLEAR_3 GPIO1_REG(0xD8)
+#define GPIO_INT_CLEAR_4 GPIO1_REG(0xDC)
+#define GPIO_INT_CLEAR_5 GPIO1_REG(0xE0)
+#define GPIO_INT_CLEAR_6 GPIO1_REG(0xE4)
+#define GPIO_INT_CLEAR_7 GPIO1_REG(0xE8)
+
+/* same pin map as above, 1=interrupt pending */
+#define GPIO_INT_STATUS_0 GPIO1_REG(0xF0)
+#define GPIO_INT_STATUS_1 GPIO2_REG(0x70)
+#define GPIO_INT_STATUS_2 GPIO1_REG(0xF4)
+#define GPIO_INT_STATUS_3 GPIO1_REG(0xF8)
+#define GPIO_INT_STATUS_4 GPIO1_REG(0xFC)
+#define GPIO_INT_STATUS_5 GPIO1_REG(0x100)
+#define GPIO_INT_STATUS_6 GPIO1_REG(0x104)
+#define GPIO_INT_STATUS_7 GPIO1_REG(0x108)
+
+#endif
diff --git a/arch/arm/mach-msm/gpio_hw.h b/arch/arm/mach-msm/gpio_hw.h
new file mode 100644
index 0000000..627dea5
--- /dev/null
+++ b/arch/arm/mach-msm/gpio_hw.h
@@ -0,0 +1,35 @@
+/* Copyright (c) 2007, Google, Inc.
+ * Copyright (c) 2008-2010, Code Aurora Forum. All rights reserved.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ */
+#ifndef __ARCH_ARM_MACH_MSM_GPIO_HW_H
+#define __ARCH_ARM_MACH_MSM_GPIO_HW_H
+
+#include <mach/msm_iomap.h>
+
+#if defined(CONFIG_ARCH_MSM7X30)
+#define GPIO1_REG(off) (MSM_GPIO1_BASE + (off))
+#define GPIO2_REG(off) (MSM_GPIO2_BASE + 0x400 + (off))
+#else
+#define GPIO1_REG(off) (MSM_GPIO1_BASE + 0x800 + (off))
+#define GPIO2_REG(off) (MSM_GPIO2_BASE + 0xC00 + (off))
+#endif
+
+#if defined(CONFIG_ARCH_QSD8X50)
+#include "gpio_hw-8x50.h"
+#elif defined(CONFIG_ARCH_MSM7X30)
+#include "gpio_hw-7x30.h"
+#else
+#include "gpio_hw-7xxx.h"
+#endif
+
+#endif
--
1.7.0.4
--
Employee of Qualcomm Innovation Center, Inc.
Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum.
next prev parent reply other threads:[~2010-06-19 16:29 UTC|newest]
Thread overview: 5+ messages / expand[flat|nested] mbox.gz Atom feed top
2010-06-19 16:29 [PATCH 0/3 v2] msm: Add gpiolib devices to MSM7x30 and QSD8x50 Gregory Bean
2010-06-19 16:29 ` Gregory Bean [this message]
2010-06-21 17:30 ` [PATCH 1/3 v2] msm: Add gpio register address mapping information Daniel Walker
2010-06-19 16:29 ` [PATCH 2/3 v2] msm: 7x30: Add gpio device configuration Gregory Bean
2010-06-19 16:29 ` [PATCH 3/3 v2] msm: 8x50: add " Gregory Bean
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1276964944-11063-2-git-send-email-gbean@codeaurora.org \
--to=gbean@codeaurora.org \
--cc=dwalker@codeaurora.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.