From: marek.vasut@gmail.com (Marek Vasut)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH 09/13] PXA: Colibri: Push evalboard MFP into module files
Date: Fri, 13 Aug 2010 06:32:40 +0200 [thread overview]
Message-ID: <1281673964-2119-9-git-send-email-marek.vasut@gmail.com> (raw)
In-Reply-To: <1281673964-2119-1-git-send-email-marek.vasut@gmail.com>
This change -- pushing the MFP configuration back into Module files -- is
necessary because some evalboards can be used with multiple modules, where MFP
differs from module to module. Therefore MFP isn't board-specific, but
module-specific and the module should preconfigure itself for the board.
(And there is also the C preprocesor limitation and conflicting #define-s)
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
---
arch/arm/mach-pxa/Kconfig | 8 +-
arch/arm/mach-pxa/colibri-pxa270-evalboard.c | 61 ++++-----------
arch/arm/mach-pxa/colibri-pxa270-income.c | 47 -----------
arch/arm/mach-pxa/colibri-pxa270.c | 96 ++++++++++++++++++++++
arch/arm/mach-pxa/colibri-pxa300.c | 61 ++++++---------
arch/arm/mach-pxa/colibri-pxa320.c | 112 ++++++++++----------------
arch/arm/mach-pxa/colibri-pxa3xx.c | 49 -----------
arch/arm/mach-pxa/include/mach/colibri.h | 6 ++
8 files changed, 188 insertions(+), 252 deletions(-)
diff --git a/arch/arm/mach-pxa/Kconfig b/arch/arm/mach-pxa/Kconfig
index 7aefb90..636cb79 100644
--- a/arch/arm/mach-pxa/Kconfig
+++ b/arch/arm/mach-pxa/Kconfig
@@ -238,10 +238,6 @@ config MACH_COLIBRI
bool "Toradex Colibri PXA270"
select PXA27x
-config MACH_COLIBRI_PXA270_EVALBOARD
- bool "Toradex Colibri Evaluation Carrier Board support (PXA270)"
- depends on MACH_COLIBRI
-
config MACH_COLIBRI_PXA270_INCOME
bool "Income s.r.o. PXA270 SBC"
depends on MACH_COLIBRI
@@ -260,6 +256,10 @@ config MACH_COLIBRI320
select PXA3xx
select CPU_PXA320
+config MACH_COLIBRI_PXA270_EVALBOARD
+ bool "Toradex Colibri Evaluation Carrier Board support"
+ depends on MACH_COLIBRI || MACH_COLIBRI300 || MACH_COLIBRI320
+
config MACH_VPAC270
bool "Voipac PXA270"
select PXA27x
diff --git a/arch/arm/mach-pxa/colibri-pxa270-evalboard.c b/arch/arm/mach-pxa/colibri-pxa270-evalboard.c
index 6177ff5..e1a2b52 100644
--- a/arch/arm/mach-pxa/colibri-pxa270-evalboard.c
+++ b/arch/arm/mach-pxa/colibri-pxa270-evalboard.c
@@ -30,61 +30,28 @@
#include "devices.h"
/******************************************************************************
- * Pin configuration
- ******************************************************************************/
-static mfp_cfg_t colibri_pxa270_evalboard_pin_config[] __initdata = {
- /* MMC */
- GPIO32_MMC_CLK,
- GPIO92_MMC_DAT_0,
- GPIO109_MMC_DAT_1,
- GPIO110_MMC_DAT_2,
- GPIO111_MMC_DAT_3,
- GPIO112_MMC_CMD,
- GPIO0_GPIO, /* SD detect */
-
- /* FFUART */
- GPIO39_FFUART_TXD,
- GPIO34_FFUART_RXD,
-
- /* UHC */
- GPIO88_USBH1_PWR,
- GPIO89_USBH1_PEN,
- GPIO119_USBH2_PWR,
- GPIO120_USBH2_PEN,
-
- /* PCMCIA */
- GPIO85_nPCE_1,
- GPIO54_nPCE_2,
- GPIO55_nPREG,
- GPIO50_nPIOR,
- GPIO51_nPIOW,
- GPIO49_nPWE,
- GPIO48_nPOE,
- GPIO57_nIOIS16,
- GPIO56_nPWAIT,
- GPIO104_PSKTSEL,
- GPIO53_GPIO, /* RESET */
- GPIO83_GPIO, /* BVD1 */
- GPIO82_GPIO, /* BVD2 */
- GPIO1_GPIO, /* READY */
- GPIO84_GPIO, /* DETECT */
- GPIO107_GPIO, /* PPEN */
-};
-
-/******************************************************************************
* SD/MMC card controller
******************************************************************************/
#if defined(CONFIG_MMC_PXA) || defined(CONFIG_MMC_PXA_MODULE)
static struct pxamci_platform_data colibri_pxa270_mci_platform_data = {
.ocr_mask = MMC_VDD_32_33 | MMC_VDD_33_34,
.gpio_power = -1,
- .gpio_card_detect = GPIO0_COLIBRI_PXA270_SD_DETECT,
.gpio_card_ro = -1,
.detect_delay_ms = 200,
};
static void __init colibri_pxa270_mmc_init(void)
{
+ if (machine_is_colibri()) /* PXA270 Colibri */
+ colibri_pxa270_mci_platform_data.gpio_card_detect =
+ GPIO0_COLIBRI_PXA270_SD_DETECT;
+ if (machine_is_colibri300()) /* PXA300 Colibri */
+ colibri_pxa270_mci_platform_data.gpio_card_detect =
+ GPIO39_COLIBRI_PXA300_SD_DETECT;
+ else /* PXA320 Colibri */
+ colibri_pxa270_mci_platform_data.gpio_card_detect =
+ GPIO28_COLIBRI_PXA320_SD_DETECT;
+
pxa_set_mci_info(&colibri_pxa270_mci_platform_data);
}
#else
@@ -103,13 +70,17 @@ static int colibri_pxa270_ohci_init(struct device *dev)
static struct pxaohci_platform_data colibri_pxa270_ohci_info = {
.port_mode = PMM_PERPORT_MODE,
- .flags = ENABLE_PORT1 | ENABLE_PORT2 |
+ .flags = ENABLE_PORT1 |
POWER_CONTROL_LOW | POWER_SENSE_LOW,
.init = colibri_pxa270_ohci_init,
};
static void __init colibri_pxa270_uhc_init(void)
{
+ /* Colibri PXA270 has two usb ports, TBA for 320 */
+ if (machine_is_colibri())
+ colibri_pxa270_ohci_info.flags |= ENABLE_PORT2;
+
pxa_set_ohci_info(&colibri_pxa270_ohci_info);
}
#else
@@ -118,7 +89,6 @@ static inline void colibri_pxa270_uhc_init(void) {}
void __init colibri_pxa270_evalboard_init(void)
{
- pxa2xx_mfp_config(ARRAY_AND_SIZE(colibri_pxa270_evalboard_pin_config));
pxa_set_ffuart_info(NULL);
pxa_set_btuart_info(NULL);
pxa_set_stuart_info(NULL);
@@ -126,4 +96,3 @@ void __init colibri_pxa270_evalboard_init(void)
colibri_pxa270_mmc_init();
colibri_pxa270_uhc_init();
}
-
diff --git a/arch/arm/mach-pxa/colibri-pxa270-income.c b/arch/arm/mach-pxa/colibri-pxa270-income.c
index 37f0f3e..07b62a0 100644
--- a/arch/arm/mach-pxa/colibri-pxa270-income.c
+++ b/arch/arm/mach-pxa/colibri-pxa270-income.c
@@ -46,52 +46,6 @@
#define GPIO113_INCOME_TS_IRQ (113)
/******************************************************************************
- * Pin configuration
- ******************************************************************************/
-static mfp_cfg_t income_pin_config[] __initdata = {
- /* MMC */
- GPIO32_MMC_CLK,
- GPIO92_MMC_DAT_0,
- GPIO109_MMC_DAT_1,
- GPIO110_MMC_DAT_2,
- GPIO111_MMC_DAT_3,
- GPIO112_MMC_CMD,
- GPIO0_GPIO, /* SD detect */
- GPIO1_GPIO, /* SD read-only */
-
- /* FFUART */
- GPIO39_FFUART_TXD,
- GPIO34_FFUART_RXD,
-
- /* BFUART */
- GPIO42_BTUART_RXD,
- GPIO43_BTUART_TXD,
- GPIO45_BTUART_RTS,
-
- /* STUART */
- GPIO46_STUART_RXD,
- GPIO47_STUART_TXD,
-
- /* UHC */
- GPIO88_USBH1_PWR,
- GPIO89_USBH1_PEN,
-
- /* LCD */
- GPIOxx_LCD_TFT_16BPP,
-
- /* PWM */
- GPIO16_PWM0_OUT,
-
- /* I2C */
- GPIO117_I2C_SCL,
- GPIO118_I2C_SDA,
-
- /* LED */
- GPIO54_GPIO, /* LED A */
- GPIO55_GPIO, /* LED B */
-};
-
-/******************************************************************************
* SD/MMC card controller
******************************************************************************/
#if defined(CONFIG_MMC_PXA) || defined(CONFIG_MMC_PXA_MODULE)
@@ -257,7 +211,6 @@ static inline void income_pwm_init(void) {}
void __init colibri_pxa270_income_boardinit(void)
{
- pxa2xx_mfp_config(ARRAY_AND_SIZE(income_pin_config));
pxa_set_ffuart_info(NULL);
pxa_set_btuart_info(NULL);
pxa_set_stuart_info(NULL);
diff --git a/arch/arm/mach-pxa/colibri-pxa270.c b/arch/arm/mach-pxa/colibri-pxa270.c
index 98673ac..8488dfe 100644
--- a/arch/arm/mach-pxa/colibri-pxa270.c
+++ b/arch/arm/mach-pxa/colibri-pxa270.c
@@ -33,6 +33,99 @@
#include "generic.h"
/******************************************************************************
+ * Evaluation board MFP
+ ******************************************************************************/
+#ifdef CONFIG_MACH_COLIBRI_PXA270_EVALBOARD
+static mfp_cfg_t colibri_pxa270_evalboard_pin_config[] __initdata = {
+ /* MMC */
+ GPIO32_MMC_CLK,
+ GPIO92_MMC_DAT_0,
+ GPIO109_MMC_DAT_1,
+ GPIO110_MMC_DAT_2,
+ GPIO111_MMC_DAT_3,
+ GPIO112_MMC_CMD,
+ GPIO0_GPIO, /* SD detect */
+
+ /* FFUART */
+ GPIO39_FFUART_TXD,
+ GPIO34_FFUART_RXD,
+
+ /* UHC */
+ GPIO88_USBH1_PWR,
+ GPIO89_USBH1_PEN,
+ GPIO119_USBH2_PWR,
+ GPIO120_USBH2_PEN,
+
+ /* PCMCIA */
+ GPIO85_nPCE_1,
+ GPIO54_nPCE_2,
+ GPIO55_nPREG,
+ GPIO50_nPIOR,
+ GPIO51_nPIOW,
+ GPIO49_nPWE,
+ GPIO48_nPOE,
+ GPIO57_nIOIS16,
+ GPIO56_nPWAIT,
+ GPIO104_PSKTSEL,
+ GPIO53_GPIO, /* RESET */
+ GPIO83_GPIO, /* BVD1 */
+ GPIO82_GPIO, /* BVD2 */
+ GPIO1_GPIO, /* READY */
+ GPIO84_GPIO, /* DETECT */
+ GPIO107_GPIO, /* PPEN */
+};
+#else
+static mfp_cfg_t colibri_pxa270_evalboard_pin_config[] __initdata = {};
+#endif
+
+#ifdef CONFIG_MACH_COLIBRI_PXA270_INCOME
+static mfp_cfg_t income_pin_config[] __initdata = {
+ /* MMC */
+ GPIO32_MMC_CLK,
+ GPIO92_MMC_DAT_0,
+ GPIO109_MMC_DAT_1,
+ GPIO110_MMC_DAT_2,
+ GPIO111_MMC_DAT_3,
+ GPIO112_MMC_CMD,
+ GPIO0_GPIO, /* SD detect */
+ GPIO1_GPIO, /* SD read-only */
+
+ /* FFUART */
+ GPIO39_FFUART_TXD,
+ GPIO34_FFUART_RXD,
+
+ /* BFUART */
+ GPIO42_BTUART_RXD,
+ GPIO43_BTUART_TXD,
+ GPIO45_BTUART_RTS,
+
+ /* STUART */
+ GPIO46_STUART_RXD,
+ GPIO47_STUART_TXD,
+
+ /* UHC */
+ GPIO88_USBH1_PWR,
+ GPIO89_USBH1_PEN,
+
+ /* LCD */
+ GPIOxx_LCD_TFT_16BPP,
+
+ /* PWM */
+ GPIO16_PWM0_OUT,
+
+ /* I2C */
+ GPIO117_I2C_SCL,
+ GPIO118_I2C_SDA,
+
+ /* LED */
+ GPIO54_GPIO, /* LED A */
+ GPIO55_GPIO, /* LED B */
+};
+#else
+static mfp_cfg_t income_pin_config[] __initdata = {};
+#endif
+
+/******************************************************************************
* Pin configuration
******************************************************************************/
static mfp_cfg_t colibri_pxa270_pin_config[] __initdata = {
@@ -185,9 +278,12 @@ static void __init colibri_pxa270_init(void)
switch (colibri_pxa270_baseboard) {
case COLIBRI_PXA270_EVALBOARD:
+ pxa2xx_mfp_config(ARRAY_AND_SIZE(
+ colibri_pxa270_evalboard_pin_config));
colibri_pxa270_evalboard_init();
break;
case COLIBRI_PXA270_INCOME:
+ pxa2xx_mfp_config(ARRAY_AND_SIZE(income_pin_config));
colibri_pxa270_income_boardinit();
break;
default:
diff --git a/arch/arm/mach-pxa/colibri-pxa300.c b/arch/arm/mach-pxa/colibri-pxa300.c
index 45c23fd..080d0e1 100644
--- a/arch/arm/mach-pxa/colibri-pxa300.c
+++ b/arch/arm/mach-pxa/colibri-pxa300.c
@@ -30,9 +30,28 @@
#include "generic.h"
#include "devices.h"
+
+#ifdef CONFIG_MACH_COLIBRI_PXA270_EVALBOARD
+static mfp_cfg_t colibri_pxa300_evalboard_pin_config[] __initdata = {
+ /* MMC */
+ GPIO7_MMC1_CLK,
+ GPIO14_MMC1_CMD,
+ GPIO3_MMC1_DAT0,
+ GPIO4_MMC1_DAT1,
+ GPIO5_MMC1_DAT2,
+ GPIO6_MMC1_DAT3,
+ GPIO39_GPIO, /* SD detect */
+
+ /* UHC */
+ GPIO0_2_USBH_PEN,
+ GPIO1_2_USBH_PWR,
+};
+#else
+static mfp_cfg_t colibri_pxa300_evalboard_pin_config[] __initdata = {};
+#endif
+
#if defined(CONFIG_AX88796)
#define COLIBRI_ETH_IRQ_GPIO mfp_to_gpio(GPIO26_GPIO)
-
/*
* Asix AX88796 Ethernet
*/
@@ -79,35 +98,6 @@ static void __init colibri_pxa300_init_eth(void)
static inline void __init colibri_pxa300_init_eth(void) {}
#endif /* CONFIG_AX88796 */
-#if defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE)
-static mfp_cfg_t colibri_pxa300_usb_pin_config[] __initdata = {
- GPIO0_2_USBH_PEN,
- GPIO1_2_USBH_PWR,
-};
-
-static struct pxaohci_platform_data colibri_pxa300_ohci_info = {
- .port_mode = PMM_GLOBAL_MODE,
- .flags = ENABLE_PORT1 | POWER_CONTROL_LOW | POWER_SENSE_LOW,
-};
-
-void __init colibri_pxa300_init_ohci(void)
-{
- pxa3xx_mfp_config(ARRAY_AND_SIZE(colibri_pxa300_usb_pin_config));
- pxa_set_ohci_info(&colibri_pxa300_ohci_info);
-}
-#else
-static inline void colibri_pxa300_init_ohci(void) {}
-#endif /* CONFIG_USB_OHCI_HCD || CONFIG_USB_OHCI_HCD_MODULE */
-
-static mfp_cfg_t colibri_pxa300_mmc_pin_config[] __initdata = {
- GPIO7_MMC1_CLK,
- GPIO14_MMC1_CMD,
- GPIO3_MMC1_DAT0,
- GPIO4_MMC1_DAT1,
- GPIO5_MMC1_DAT2,
- GPIO6_MMC1_DAT3,
-};
-
#if defined(CONFIG_FB_PXA) || defined(CONFIG_FB_PXA_MODULE)
static mfp_cfg_t colibri_pxa300_lcd_pin_config[] __initdata = {
GPIO54_LCD_LDD_0,
@@ -170,18 +160,15 @@ static inline void colibri_pxa310_init_ac97(void) {}
void __init colibri_pxa300_init(void)
{
- pxa_set_ffuart_info(NULL);
- pxa_set_btuart_info(NULL);
- pxa_set_stuart_info(NULL);
-
colibri_pxa300_init_eth();
- colibri_pxa300_init_ohci();
colibri_pxa3xx_init_nand();
colibri_pxa300_init_lcd();
colibri_pxa3xx_init_lcd(mfp_to_gpio(GPIO39_GPIO));
colibri_pxa310_init_ac97();
- colibri_pxa3xx_init_mmc(ARRAY_AND_SIZE(colibri_pxa300_mmc_pin_config),
- mfp_to_gpio(MFP_PIN_GPIO13));
+
+ /* Evalboard init */
+ pxa3xx_mfp_config(ARRAY_AND_SIZE(colibri_pxa300_evalboard_pin_config));
+ colibri_pxa270_evalboard_init();
}
MACHINE_START(COLIBRI300, "Toradex Colibri PXA300")
diff --git a/arch/arm/mach-pxa/colibri-pxa320.c b/arch/arm/mach-pxa/colibri-pxa320.c
index 99e850d..e886ab2 100644
--- a/arch/arm/mach-pxa/colibri-pxa320.c
+++ b/arch/arm/mach-pxa/colibri-pxa320.c
@@ -35,9 +35,47 @@
#include "generic.h"
#include "devices.h"
+#ifdef CONFIG_MACH_COLIBRI_PXA270_EVALBOARD
+static mfp_cfg_t colibri_pxa320_evalboard_pin_config[] __initdata = {
+ /* MMC */
+ GPIO22_MMC1_CLK,
+ GPIO23_MMC1_CMD,
+ GPIO18_MMC1_DAT0,
+ GPIO19_MMC1_DAT1,
+ GPIO20_MMC1_DAT2,
+ GPIO21_MMC1_DAT3,
+ GPIO28_GPIO, /* SD detect */
+
+ /* UART 1 configuration (may be set by bootloader) */
+ GPIO99_UART1_CTS,
+ GPIO104_UART1_RTS,
+ GPIO97_UART1_RXD,
+ GPIO98_UART1_TXD,
+ GPIO101_UART1_DTR,
+ GPIO103_UART1_DSR,
+ GPIO100_UART1_DCD,
+ GPIO102_UART1_RI,
+
+ /* UART 2 configuration */
+ GPIO109_UART2_CTS,
+ GPIO112_UART2_RTS,
+ GPIO110_UART2_RXD,
+ GPIO111_UART2_TXD,
+
+ /* UART 3 configuration */
+ GPIO30_UART3_RXD,
+ GPIO31_UART3_TXD,
+
+ /* UHC */
+ GPIO2_2_USBH_PEN,
+ GPIO3_2_USBH_PWR,
+};
+#else
+static mfp_cfg_t colibri_pxa320_evalboard_pin_config[] __initdata = {};
+#endif
+
#if defined(CONFIG_AX88796)
#define COLIBRI_ETH_IRQ_GPIO mfp_to_gpio(GPIO36_GPIO)
-
/*
* Asix AX88796 Ethernet
*/
@@ -84,26 +122,6 @@ static void __init colibri_pxa320_init_eth(void)
static inline void __init colibri_pxa320_init_eth(void) {}
#endif /* CONFIG_AX88796 */
-#if defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE)
-static mfp_cfg_t colibri_pxa320_usb_pin_config[] __initdata = {
- GPIO2_2_USBH_PEN,
- GPIO3_2_USBH_PWR,
-};
-
-static struct pxaohci_platform_data colibri_pxa320_ohci_info = {
- .port_mode = PMM_GLOBAL_MODE,
- .flags = ENABLE_PORT1 | POWER_CONTROL_LOW | POWER_SENSE_LOW,
-};
-
-void __init colibri_pxa320_init_ohci(void)
-{
- pxa3xx_mfp_config(ARRAY_AND_SIZE(colibri_pxa320_usb_pin_config));
- pxa_set_ohci_info(&colibri_pxa320_ohci_info);
-}
-#else
-static inline void colibri_pxa320_init_ohci(void) {}
-#endif /* CONFIG_USB_OHCI_HCD || CONFIG_USB_OHCI_HCD_MODULE */
-
#if defined(CONFIG_USB_GADGET_PXA27X)||defined(CONFIG_USB_GADGET_PXA27X_MODULE)
static struct gpio_vbus_mach_info colibri_pxa320_gpio_vbus_info = {
.gpio_vbus = mfp_to_gpio(MFP_PIN_GPIO96),
@@ -140,15 +158,6 @@ static void __init colibri_pxa320_init_udc(void)
static inline void colibri_pxa320_init_udc(void) {}
#endif
-static mfp_cfg_t colibri_pxa320_mmc_pin_config[] __initdata = {
- GPIO22_MMC1_CLK,
- GPIO23_MMC1_CMD,
- GPIO18_MMC1_DAT0,
- GPIO19_MMC1_DAT1,
- GPIO20_MMC1_DAT2,
- GPIO21_MMC1_DAT3
-};
-
#if defined(CONFIG_FB_PXA) || defined(CONFIG_FB_PXA_MODULE)
static mfp_cfg_t colibri_pxa320_lcd_pin_config[] __initdata = {
GPIO6_2_LCD_LDD_0,
@@ -205,53 +214,18 @@ static inline void __init colibri_pxa320_init_ac97(void)
static inline void colibri_pxa320_init_ac97(void) {}
#endif
-/*
- * The following configuration is verified to work with the Toradex Orchid
- * carrier board
- */
-static mfp_cfg_t colibri_pxa320_uart_pin_config[] __initdata = {
- /* UART 1 configuration (may be set by bootloader) */
- GPIO99_UART1_CTS,
- GPIO104_UART1_RTS,
- GPIO97_UART1_RXD,
- GPIO98_UART1_TXD,
- GPIO101_UART1_DTR,
- GPIO103_UART1_DSR,
- GPIO100_UART1_DCD,
- GPIO102_UART1_RI,
-
- /* UART 2 configuration */
- GPIO109_UART2_CTS,
- GPIO112_UART2_RTS,
- GPIO110_UART2_RXD,
- GPIO111_UART2_TXD,
-
- /* UART 3 configuration */
- GPIO30_UART3_RXD,
- GPIO31_UART3_TXD,
-};
-
-static void __init colibri_pxa320_init_uart(void)
-{
- pxa3xx_mfp_config(ARRAY_AND_SIZE(colibri_pxa320_uart_pin_config));
-}
-
void __init colibri_pxa320_init(void)
{
- pxa_set_ffuart_info(NULL);
- pxa_set_btuart_info(NULL);
- pxa_set_stuart_info(NULL);
-
colibri_pxa320_init_eth();
- colibri_pxa320_init_ohci();
colibri_pxa3xx_init_nand();
colibri_pxa320_init_lcd();
colibri_pxa3xx_init_lcd(mfp_to_gpio(GPIO49_GPIO));
colibri_pxa320_init_ac97();
- colibri_pxa3xx_init_mmc(ARRAY_AND_SIZE(colibri_pxa320_mmc_pin_config),
- mfp_to_gpio(MFP_PIN_GPIO28));
- colibri_pxa320_init_uart();
colibri_pxa320_init_udc();
+
+ /* Evalboard init */
+ pxa3xx_mfp_config(ARRAY_AND_SIZE(colibri_pxa320_evalboard_pin_config));
+ colibri_pxa270_evalboard_init();
}
MACHINE_START(COLIBRI320, "Toradex Colibri PXA320")
diff --git a/arch/arm/mach-pxa/colibri-pxa3xx.c b/arch/arm/mach-pxa/colibri-pxa3xx.c
index 199afa2..96b2d9f 100644
--- a/arch/arm/mach-pxa/colibri-pxa3xx.c
+++ b/arch/arm/mach-pxa/colibri-pxa3xx.c
@@ -64,55 +64,6 @@ void __init colibri_pxa3xx_init_eth(struct ax_plat_data *plat_data)
}
#endif
-#if defined(CONFIG_MMC_PXA) || defined(CONFIG_MMC_PXA_MODULE)
-static int mmc_detect_pin;
-
-static int colibri_pxa3xx_mci_init(struct device *dev,
- irq_handler_t colibri_mmc_detect_int,
- void *data)
-{
- int ret;
-
- ret = gpio_request(mmc_detect_pin, "mmc card detect");
- if (ret)
- return ret;
-
- gpio_direction_input(mmc_detect_pin);
- ret = request_irq(gpio_to_irq(mmc_detect_pin), colibri_mmc_detect_int,
- IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING,
- "MMC card detect", data);
- if (ret) {
- gpio_free(mmc_detect_pin);
- return ret;
- }
-
- return 0;
-}
-
-static void colibri_pxa3xx_mci_exit(struct device *dev, void *data)
-{
- free_irq(mmc_detect_pin, data);
- gpio_free(gpio_to_irq(mmc_detect_pin));
-}
-
-static struct pxamci_platform_data colibri_pxa3xx_mci_platform_data = {
- .detect_delay_ms = 200,
- .ocr_mask = MMC_VDD_32_33 | MMC_VDD_33_34,
- .init = colibri_pxa3xx_mci_init,
- .exit = colibri_pxa3xx_mci_exit,
- .gpio_card_detect = -1,
- .gpio_card_ro = -1,
- .gpio_power = -1,
-};
-
-void __init colibri_pxa3xx_init_mmc(mfp_cfg_t *pins, int len, int detect_pin)
-{
- pxa3xx_mfp_config(pins, len);
- mmc_detect_pin = detect_pin;
- pxa_set_mci_info(&colibri_pxa3xx_mci_platform_data);
-}
-#endif /* CONFIG_MMC_PXA || CONFIG_MMC_PXA_MODULE */
-
#if defined(CONFIG_FB_PXA) || defined(CONFIG_FB_PXA_MODULE)
static int lcd_bl_pin;
diff --git a/arch/arm/mach-pxa/include/mach/colibri.h b/arch/arm/mach-pxa/include/mach/colibri.h
index 58dada1..63a948a 100644
--- a/arch/arm/mach-pxa/include/mach/colibri.h
+++ b/arch/arm/mach-pxa/include/mach/colibri.h
@@ -59,5 +59,11 @@ static inline void colibri_pxa3xx_init_nand(void) {}
#define GPIO0_COLIBRI_PXA270_SD_DETECT 0
#define GPIO113_COLIBRI_PXA270_TS_IRQ 113
+/* GPIO definitions for Colibri PXA300/310 */
+#define GPIO39_COLIBRI_PXA300_SD_DETECT 39
+
+/* GPIO definitions for Colibri PXA320 */
+#define GPIO28_COLIBRI_PXA320_SD_DETECT 28
+
#endif /* _COLIBRI_H_ */
--
1.7.1
next prev parent reply other threads:[~2010-08-13 4:32 UTC|newest]
Thread overview: 20+ messages / expand[flat|nested] mbox.gz Atom feed top
2010-08-13 4:32 [PATCH 01/13] Balloon3: Disperse MFP config Marek Vasut
2010-08-13 4:32 ` [PATCH 02/13] PXA: Vpac270: Fix gpio_power for MMC Marek Vasut
2010-08-13 4:32 ` [PATCH 03/13] PXA: PalmTC: Modularize Palm Tungsten|C Marek Vasut
2010-08-13 4:32 ` [PATCH 04/13] UCB1400: Pass ucb1400-gpio data through ac97 bus Marek Vasut
2010-08-13 4:32 ` [PATCH 05/13] PXA: Vpac270: Correct touch IRQ passing to UCB1400 Marek Vasut
2010-08-13 4:32 ` [PATCH 06/13] PXA: PalmTC: Pass GPIO offset to ucb1400-gpio Marek Vasut
2010-08-13 4:32 ` [PATCH 07/13] PXA: PalmTC: Add gpio-leds and vibrator support Marek Vasut
2010-08-13 4:32 ` [PATCH 08/13] PXA: Colibri: Toradex Colibri PXA270 CF support Marek Vasut
2010-08-18 11:43 ` Daniel Mack
2010-08-21 6:22 ` Marek Vasut
2010-08-21 9:33 ` Daniel Mack
2010-09-01 7:23 ` Russell King - ARM Linux
2010-09-01 12:39 ` Marek Vasut
2010-08-13 4:32 ` Marek Vasut [this message]
2010-08-13 4:32 ` [PATCH 10/13] PXA: Colibri: Add M41T00 RTC support Marek Vasut
2010-08-13 4:32 ` [PATCH 11/13] PXA: Colibri: Rename Colibri-evalboard Marek Vasut
2010-08-13 4:32 ` [PATCH 12/13] pxa2xx/pcmcia: Prepare for pxa320 Marek Vasut
2010-08-13 4:32 ` [PATCH 13/13] PXA: Colibri PXA320 PCMCIA driver Marek Vasut
2010-08-18 4:11 ` [PATCH 01/13] Balloon3: Disperse MFP config Eric Miao
2010-08-18 5:05 ` Marek Vasut
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1281673964-2119-9-git-send-email-marek.vasut@gmail.com \
--to=marek.vasut@gmail.com \
--cc=linux-arm-kernel@lists.infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.