On Wed, 2010-11-17 at 13:03 +1100, Michael Neuling wrote:
> 
> In message <1289958663.3028.175.camel@localhost> you wrote:
> > On Tue, 2010-11-16 at 14:26 +1100, Michael Neuling wrote:
> > > In message <1289520464.4752.12.camel@localhost> you wrote:
> > > > On Thu, 2010-11-11 at 09:06 +1100, Benjamin Herrenschmidt wrote:
> > > > > On Wed, 2010-11-10 at 11:54 -0800, Jim Keniston wrote:
> > > > > > I got Ben's linux/kernel/git/benh/powerpc.git source and built it
> > > > > > (.config file attached*).  It hangs on boot.  When I boot it with
> > > > > > loglevel=8, its last words are:
> > > > > 
> > > > > First, please try with Linus upstream. The "master" branch in my git
> > > > > tree is quite stale, and my next and merge branch are too at the moment
> > > > > as I'm still travelling. All our current stuff was merged during the
> > > > > last merge window so there's nothing "new" for you to pickup in my tree
> > > > > at the moment :-)
> > > > > 
> > > > > If the problem still occurs, I'll have a look next week.
> > > > > 
> > > > > Cheers,
> > > > > Ben.
> > > > 
> > > > I built from Linus's git tree, and that kernel doesn't boot, either.
> > > > (It doesn't hang, but rather panics during boot.  I can provide a
> > > > console log if you like.)
> > > 
> > > Yes please.  
> > > 
> > > Linus' tree with pseries_defconfig boots fine for me on my POWER5 box.
> > > 
> > > > v2.6.36 and v2.6.37-rc1 boot fine for me.  I'll post my nvram-related
> > > > patches against v2.6.37-rc1.
> > > 
> > > So it's broken between 37-rc1 and whereever you grabbed Linus tree.
> > > That's a fairly small window.  Can you bisect it?
> > 
> > I was apparently comparing apples to oranges.  Given the fatal
> > configuration options (DEBUG_SLAB and/or DEBUG_PAGEALLOC) 2.6.37-rc1
> > fails the same as a more recent snapshot of Linus's tree.  I updated my
> > view today, and it still fails to boot with DEBUG_SLAB and/or
> > DEBUG_PAGEALLOC, and boots OK without them.
> 
> I can't reproduce any of these.
> 
> I modified pseries_defconfig to enable DEBUG_SLAB and it still works for
> me on my POWER5 here
> 
> % grep SLAB .config
> CONFIG_SLAB=y
> CONFIG_SLABINFO=y
> CONFIG_DEBUG_SLAB=y
> # CONFIG_DEBUG_SLAB_LEAK is not set
> 
> I also can't reproduce with DEBUG_PAGEALLOC enabeled either.
> 
> > It also fails to boot with SLUB and SLUB_DEBUG enabled, even with
> > SLUB_DEBUG_ON disabled.
> 
> pseries_defconfig uses this configuration and boots for me.
> 
> % grep SLUB .config
> CONFIG_SLUB_DEBUG=y
> CONFIG_SLUB=y
> # CONFIG_SLUB_DEBUG_ON is not set
> # CONFIG_SLUB_STATS is not set
> 
> > Ben has access to my system, and will look at it in a few days.
> 
> Can you please try pseries_defconfig?

It boots fine with pseries_defconfig.

Attached is the config file that I've been using, which is probably
descended over many generations of kernels from some config file in my
machine's distant past.  (Enable DEBUG_SLAB or DEBUG_PAGEALLOC and it
will fail to boot.)  After I run 'make menuconfig' starting from
pseries_defconfig...
$ diff config_ok .config | wc -l
2052

> 
> Mikey
> _______________________________________________
> Linuxppc-dev mailing list
> Linuxppc-dev@lists.ozlabs.org
> https://lists.ozlabs.org/listinfo/linuxppc-dev

Jim