From mboxrd@z Thu Jan 1 00:00:00 1970 From: Mark Brown Subject: [PATCH 3/3] ASoC: Use explicit sequence for WM8903 bias off Date: Thu, 10 Feb 2011 14:44:48 +0000 Message-ID: <1297349088-26820-3-git-send-email-broonie@opensource.wolfsonmicro.com> References: <1297349088-26820-1-git-send-email-broonie@opensource.wolfsonmicro.com> Mime-Version: 1.0 Content-Type: text/plain; charset="us-ascii" Content-Transfer-Encoding: 7bit Return-path: Received: from opensource2.wolfsonmicro.com (opensource.wolfsonmicro.com [80.75.67.52]) by alsa0.perex.cz (Postfix) with ESMTP id 60F8824524 for ; Thu, 10 Feb 2011 15:44:52 +0100 (CET) In-Reply-To: <1297349088-26820-1-git-send-email-broonie@opensource.wolfsonmicro.com> List-Unsubscribe: , List-Archive: List-Post: List-Help: List-Subscribe: , Sender: alsa-devel-bounces@alsa-project.org Errors-To: alsa-devel-bounces@alsa-project.org To: Liam Girdwood Cc: alsa-devel@alsa-project.org, patches@opensource.wolfsonmicro.com, Mark Brown List-Id: alsa-devel@alsa-project.org This makes no real difference compared to the write sequencer sequence that was previously used but can run without a clock being provided. Also remove the write sequencer support code as this was the last use of it. Signed-off-by: Mark Brown --- sound/soc/codecs/wm8903.c | 66 ++++++++++++++------------------------------ 1 files changed, 21 insertions(+), 45 deletions(-) diff --git a/sound/soc/codecs/wm8903.c b/sound/soc/codecs/wm8903.c index c7faeea..20325b3 100644 --- a/sound/soc/codecs/wm8903.c +++ b/sound/soc/codecs/wm8903.c @@ -230,8 +230,6 @@ struct wm8903_priv { /* Reference count */ int class_w_users; - struct completion wseq; - struct snd_soc_jack *mic_jack; int mic_det; int mic_short; @@ -267,41 +265,6 @@ static int wm8903_volatile_register(struct snd_soc_codec *codec, unsigned int re } } -static int wm8903_run_sequence(struct snd_soc_codec *codec, unsigned int start) -{ - u16 reg[5]; - struct wm8903_priv *wm8903 = snd_soc_codec_get_drvdata(codec); - - BUG_ON(start > 48); - - /* Enable the sequencer if it's not already on */ - reg[0] = snd_soc_read(codec, WM8903_WRITE_SEQUENCER_0); - snd_soc_write(codec, WM8903_WRITE_SEQUENCER_0, - reg[0] | WM8903_WSEQ_ENA); - - dev_dbg(codec->dev, "Starting sequence at %d\n", start); - - snd_soc_write(codec, WM8903_WRITE_SEQUENCER_3, - start | WM8903_WSEQ_START); - - /* Wait for it to complete. If we have the interrupt wired up then - * that will break us out of the poll early. - */ - do { - wait_for_completion_timeout(&wm8903->wseq, - msecs_to_jiffies(10)); - - reg[4] = snd_soc_read(codec, WM8903_WRITE_SEQUENCER_4); - } while (reg[4] & WM8903_WSEQ_BUSY); - - dev_dbg(codec->dev, "Sequence complete\n"); - - /* Disable the sequencer again if we enabled it */ - snd_soc_write(codec, WM8903_WRITE_SEQUENCER_0, reg[0]); - - return 0; -} - static void wm8903_reset(struct snd_soc_codec *codec) { snd_soc_write(codec, WM8903_SW_RESET_AND_ID, 0); @@ -1218,11 +1181,26 @@ static int wm8903_set_bias_level(struct snd_soc_codec *codec, break; case SND_SOC_BIAS_OFF: - snd_soc_update_bits(codec, WM8903_CLOCK_RATES_2, - WM8903_CLK_SYS_ENA, WM8903_CLK_SYS_ENA); - wm8903_run_sequence(codec, 32); - snd_soc_update_bits(codec, WM8903_CLOCK_RATES_2, - WM8903_CLK_SYS_ENA, 0); + snd_soc_update_bits(codec, WM8903_BIAS_CONTROL_0, + WM8903_BIAS_ENA, 0); + + snd_soc_update_bits(codec, WM8903_VMID_CONTROL_0, + WM8903_VMID_SOFT_MASK, + 2 << WM8903_VMID_SOFT_SHIFT); + + snd_soc_update_bits(codec, WM8903_VMID_CONTROL_0, + WM8903_VMID_BUF_ENA, 0); + + msleep(290); + + snd_soc_update_bits(codec, WM8903_VMID_CONTROL_0, + WM8903_VMID_TIE_ENA | WM8903_BUFIO_ENA | + WM8903_VMID_IO_ENA | WM8903_VMID_RES_MASK | + WM8903_VMID_SOFT_MASK | + WM8903_VMID_BUF_ENA, 0); + + snd_soc_update_bits(codec, WM8903_BIAS_CONTROL_0, + WM8903_STARTUP_BIAS_ENA, 0); break; } @@ -1864,8 +1842,7 @@ static irqreturn_t wm8903_irq(int irq, void *data) int_val = snd_soc_read(codec, WM8903_INTERRUPT_STATUS_1) & mask; if (int_val & WM8903_WSEQ_BUSY_EINT) { - dev_dbg(codec->dev, "Write sequencer done\n"); - complete(&wm8903->wseq); + dev_warn(codec->dev, "Write sequencer done\n"); } /* @@ -2120,7 +2097,6 @@ static int wm8903_probe(struct snd_soc_codec *codec) u16 val; wm8903->codec = codec; - init_completion(&wm8903->wseq); ret = snd_soc_codec_set_cache_io(codec, 8, 16, SND_SOC_I2C); if (ret != 0) { -- 1.7.2.3