From: Lawrence Rust <lawrence@softsystem.co.uk>
To: Linux Media Mailing List <linux-media@vger.kernel.org>
Subject: Hauppauge Nova-S remote control broken in 2.6.38
Date: Sun, 03 Apr 2011 13:41:49 +0200 [thread overview]
Message-ID: <1301830909.1709.32.camel@gagarin> (raw)
I just installed a new 2.6.38.2 kernel and found that the remote control
on my Hauppauge Nova-S plus is no longer working. dmesg shows that
everything initialised OK:
[ 8.002874] cx88/0: cx2388x v4l2 driver version 0.0.8 loaded
[ 8.100260] IR NEC protocol handler initialized
[ 8.132843] tveeprom 1-0050: Hauppauge model 92001, rev C1B1, serial# 2700305
[ 8.132853] tveeprom 1-0050: MAC address is 00:0d:fe:29:34:11
[ 8.132858] tveeprom 1-0050: tuner model is Conexant_CX24109 (idx 111, type 4)
[ 8.132864] tveeprom 1-0050: TV standards ATSC/DVB Digital (eeprom 0x80)
[ 8.132870] tveeprom 1-0050: audio processor is CX883 (idx 32)
[ 8.132875] tveeprom 1-0050: decoder processor is CX883 (idx 22)
[ 8.132879] tveeprom 1-0050: has no radio, has IR receiver, has no IR transmitter
[ 8.132884] cx88[0]: hauppauge eeprom: model=92001
[ 8.229173] IR RC5(x) protocol handler initialized
[ 8.261811] Registered IR keymap rc-hauppauge-new
[ 8.272593] input: cx88 IR (Hauppauge Nova-S-Plus as /devices/pci0000:00/0000:00:0b.2/rc/rc0/input3
[ 8.275331] IR RC6 protocol handler initialized
[ 8.278600] rc0: cx88 IR (Hauppauge Nova-S-Plus as /devices/pci0000:00/0000:00:0b.2/rc/rc0
[ 8.510290] lirc_dev: IR Remote Control driver registered, major 251
[ 8.581417] rc rc0: lirc_dev: driver ir-lirc-codec (cx88xx) registered at minor = 0
[ 8.581427] IR LIRC bridge handler initialized
cat /proc/bus/input/devices
...
I: Bus=0001 Vendor=0070 Product=9202 Version=0001
N: Name="cx88 IR (Hauppauge Nova-S-Plus "
P: Phys=pci-0000:00:0b.2/ir0
S: Sysfs=/devices/pci0000:00/0000:00:0b.2/rc/rc0/input3
But if I try to receive input events I see nothing:
sudo evtest /dev/input/event3
Input driver version is 1.0.1
Input device ID: bus 0x1 vendor 0x70 product 0x9202 version 0x1
Input device name: "cx88 IR (Hauppauge Nova-S-Plus "
Supported events:
...
If I enable debug output:
echo >/sys/module/rc_core/parameters/debug 2
and press a key, dmesg shows:
[ 481.765937] ir_raw_event_set_idle: leave idle mode
[ 481.765948] ir_raw_event_store: sample: (01000us pulse)
[ 481.765970] ir_rc5_decode: RC5(x) decode started at state 0 (1000us pulse)
[ 481.765975] ir_rc5_decode: RC5(x) decode started at state 1 (111us pulse)
[ 481.765981] ir_rc6_decode: RC6 decode started at state 0 (1000us pulse)
[ 481.765986] ir_rc6_decode: RC6 decode failed at state 0 (1000us pulse)
[ 481.765995] ir_lirc_decode: delivering 1000us pulse to lirc_dev
[ 481.773939] ir_raw_event_store: sample: (00750us space)
[ 481.773946] ir_raw_event_store: sample: (01000us pulse)
[ 481.773950] ir_raw_event_store: sample: (00750us space)
[ 481.773954] ir_raw_event_store: sample: (01000us pulse)
[ 481.773958] ir_raw_event_store: sample: (01000us space)
[ 481.773961] ir_raw_event_store: sample: (00750us pulse)
[ 481.773965] ir_raw_event_store: sample: (01000us space)
[ 481.773969] ir_raw_event_store: sample: (00750us pulse)
[ 481.773973] ir_raw_event_store: sample: (01000us space)
[ 481.774007] ir_rc5_decode: RC5(x) decode started at state 1 (750us space)
[ 481.774013] ir_rc6_decode: RC6 decode started at state 0 (750us space)
[ 481.774018] ir_rc6_decode: RC6 decode failed at state 0 (750us space)
[ 481.774025] ir_lirc_decode: delivering 750us space to lirc_dev
[ 481.774030] ir_rc5_decode: RC5(x) decode started at state 2 (1000us pulse)
[ 481.774035] ir_rc5_decode: RC5(x) decode started at state 1 (111us pulse)
[ 481.774039] ir_rc6_decode: RC6 decode started at state 0 (1000us pulse)
[ 481.774043] ir_rc6_decode: RC6 decode failed at state 0 (1000us pulse)
[ 481.774047] ir_lirc_decode: delivering 1000us pulse to lirc_dev
[ 481.774051] ir_rc5_decode: RC5(x) decode started at state 1 (750us space)
[ 481.774055] ir_rc6_decode: RC6 decode started at state 0 (750us space)
[ 481.774059] ir_rc6_decode: RC6 decode failed at state 0 (750us space)
[ 481.774063] ir_lirc_decode: delivering 750us space to lirc_dev
So it looks like decoding is failing. I see that there have been
extensive changes to the RC system from 2.6.37 and it appears that
something broke in the transition. Any suggestions on where the problem
might be?
--
Lawrence
next reply other threads:[~2011-04-03 11:41 UTC|newest]
Thread overview: 4+ messages / expand[flat|nested] mbox.gz Atom feed top
2011-04-03 11:41 Lawrence Rust [this message]
2011-04-03 14:25 ` Hauppauge Nova-S remote control broken in 2.6.38 Mauro Carvalho Chehab
2011-04-03 14:48 ` Lawrence Rust
2011-04-04 12:43 ` Mauro Carvalho Chehab
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1301830909.1709.32.camel@gagarin \
--to=lawrence@softsystem.co.uk \
--cc=linux-media@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.