From: Jeffrey Scott Flesher Gmail <jeffrey.scott.flesher@gmail.com>
To: Daniel Mack <zonque@gmail.com>
Cc: alsa-devel@alsa-project.org
Subject: Re: GR-55 Driver
Date: Wed, 18 May 2011 08:34:53 -0700 [thread overview]
Message-ID: <1305732893.3209.5.camel@TrinaryDragon> (raw)
In-Reply-To: <BANLkTik_oWtWLN+6Y_j7RznUzvztrzZybA@mail.gmail.com>
Does this type of data (USBlyzer Report) help to write drivers?
http://vetshelpcenter.com/media/GR-55-USB-Anlyzer.html
-----Original Message-----
From: Daniel Mack <zonque@gmail.com>
To: Jeffrey Scott Flesher Gmail <jeffrey.scott.flesher@gmail.com>
Cc: alsa-devel@alsa-project.org
Subject: Re: [alsa-devel] GR-55 Driver
Date: Tue, 17 May 2011 12:11:14 +0200
On Mon, May 16, 2011 at 11:33 PM, Jeffrey Scott Flesher Gmail
<jeffrey.scott.flesher@gmail.com> wrote:
> # alsamixer -D hw:GR55
> This sound device does not have any controls.
> ***
> # amixer -D hw:GR55 controls
> [Nothing]
That's possible.
> ***
> # cat /proc/asound/GR55/stream0
> Roland GR-55 at usb-0000:00:12.2-4, high speed : USB Audio
>
> Playback:
> Status: Stop
> Interface 0
> Altset 1
> Format: S32_LE
> Channels: 2
> Endpoint: 5 OUT (ASYNC)
> Rates: 44100
> Data packet interval: 125 us
>
> Capture:
> Status: Stop
> Interface 1
> Altset 1
> Format: S32_LE
> Channels: 2
> Endpoint: 4 IN (ASYNC)
> Rates: 44100
> Data packet interval: 125 us
> ***
> # cat /proc/asound/GR55/midi0
> GR-55
Looks ok.
> ***
> # aplay -D plughw:GR55,0,0 /usr/share/sounds/alsa/Front_Center.wav
> Playing WAVE '/usr/share/sounds/alsa/Front_Center.wav' : Signed 16 bit Little Endian, Rate 48000 Hz, Mono
> [No sound]
Can you try this with a 44100/16bit file?
> I am facing two problems, I am unfamiliar with this piece of equipment and as a result, I'm unsure how to test it.
>
> Testing Audio function:
> I tested it with Audacity in Windozes and it works; in Linux I set it up the same way: GR-55 USB Audio (hw:1,0) as recording device; no sound.
Are you sure hw:1,0 refers to your GR-55? Check the entries in
/proc/asound/cards again, please.
> Using Logitech Webcam software I can record the guitar output; Using Cheese, I do not get Audio.
So you DO in fact get audio from the device then with some tool?
> Testing MIDI function:
> I'm going to call tech support on this one; I have not found a Windows app that seems to work with the MIDI;
For Windows, Midi-OX is a good tool to test with: http://www.midiox.com/
> so I can not expect to test this in Linux yet; I would like to be able to convert notes into sheet music; I tried TuxGuitar, but must admit I don't know how to get it to work with MIDI input, or if it even does.
For Linux, use amidi. "amidi -l" will list all available MIDI ports.
For example to dump all incoming messages, use "amidi --port hw:X,0
--dump". And to send messages, use "--send-hex" and make sure you send
valid MIDI messages, otherwise the other side won't do anything.
> I'm going to keep on this till I get it 100%; I have patience; lets hope you do too.
Well, I believe the quirks patch is correct, and there's only software
configuration issues left.
Daniel
next prev parent reply other threads:[~2011-05-18 15:34 UTC|newest]
Thread overview: 18+ messages / expand[flat|nested] mbox.gz Atom feed top
2011-05-12 18:20 GR-55 Driver Jeffrey Scott Flesher Gmail
2011-05-12 19:47 ` Daniel Mack
[not found] ` <1305233604.8214.2.camel@TrinaryDragon>
2011-05-13 0:16 ` Daniel Mack
[not found] ` <1305253856.5076.65.camel@TrinaryDragon>
2011-05-13 7:29 ` Daniel Mack
[not found] ` <BANLkTi=jj7cjxgmOpH+EHnUMuazqLOEsZA@mail.gmail.com>
2011-05-15 6:39 ` Jeffrey Scott Flesher Gmail
2011-05-15 11:36 ` Daniel Mack
2011-05-15 23:13 ` Jeffrey Scott Flesher Gmail
2011-05-16 7:05 ` Daniel Mack
2011-05-16 21:33 ` Jeffrey Scott Flesher Gmail
2011-05-17 10:11 ` Daniel Mack
2011-05-18 5:24 ` Jeffrey Scott Flesher Gmail
2011-05-18 15:34 ` Jeffrey Scott Flesher Gmail [this message]
2011-05-18 17:39 ` Daniel Mack
2011-05-19 21:09 ` Jeffrey Scott Flesher Gmail
2011-05-23 16:01 ` Keith A. Milner
2011-05-23 17:08 ` Daniel Mack
2011-05-24 13:30 ` Keith A. Milner
2011-05-24 18:28 ` Jeffrey Scott Flesher Gmail
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1305732893.3209.5.camel@TrinaryDragon \
--to=jeffrey.scott.flesher@gmail.com \
--cc=alsa-devel@alsa-project.org \
--cc=zonque@gmail.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.