[Qemu-devel] [PATCH 07/10] fdc: check if media rate is correct before doing any transfer

["Hervé Poussineau" <hpoussin@reactos.org>]

Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
---
 hw/fdc.c |   24 +++++++++++++++++++++++-
 1 files changed, 23 insertions(+), 1 deletions(-)

diff --git a/hw/fdc.c b/hw/fdc.c
index aec1e5e..ddfa91f 100644
--- a/hw/fdc.c
+++ b/hw/fdc.c
@@ -83,6 +83,7 @@ typedef struct FDrive {
     uint16_t bps;             /* Bytes per sector       */
     uint8_t ro;               /* Is read-only           */
     uint8_t media_changed;    /* Is media changed       */
+    uint8_t media_rate;       /* Data rate of medium    */
 } FDrive;
 
 static void fd_init(FDrive *drv)
@@ -195,6 +196,7 @@ static void fd_revalidate(FDrive *drv)
         drv->last_sect = last_sect;
         drv->ro = ro;
         drv->drive = drive;
+        drv->media_rate = rate;
     } else {
         FLOPPY_DPRINTF("No disk in drive\n");
         drv->last_sect = 0;
@@ -301,6 +303,7 @@ enum {
 };
 
 enum {
+    FD_SR1_MA       = 0x01, /* Missing address mark */
     FD_SR1_NW       = 0x02, /* Not writable */
     FD_SR1_EC       = 0x80, /* End of cylinder */
 };
@@ -1055,6 +1058,18 @@ static void fdctrl_start_transfer(FDCtrl *fdctrl, int direction)
         break;
     }
 
+    /* Check the data rate. If the programmed data rate does not match
+     * the currently inserted medium, the operation has to fail. */
+    if ((fdctrl->dsr & FD_DSR_DRATEMASK) != cur_drv->media_rate) {
+        FLOPPY_DPRINTF("data rate mismatch (fdc=%d, media=%d)\n",
+                       fdctrl->dsr & FD_DSR_DRATEMASK, cur_drv->media_rate);
+        fdctrl_stop_transfer(fdctrl, FD_SR0_ABNTERM, FD_SR1_MA, 0x00);
+        fdctrl->fifo[3] = kt;
+        fdctrl->fifo[4] = kh;
+        fdctrl->fifo[5] = ks;
+        return;
+    }
+
     /* Set the FIFO state */
     fdctrl->data_dir = direction;
     fdctrl->data_pos = 0;
@@ -1777,7 +1792,14 @@ static void fdctrl_result_timer(void *opaque)
     if (cur_drv->last_sect != 0) {
         cur_drv->sect = (cur_drv->sect % cur_drv->last_sect) + 1;
     }
-    fdctrl_stop_transfer(fdctrl, 0x00, 0x00, 0x00);
+    /* READ_ID can't automatically succeed! */
+    if ((fdctrl->dsr & FD_DSR_DRATEMASK) != cur_drv->media_rate) {
+        FLOPPY_DPRINTF("read id rate mismatch (fdc=%d, media=%d)\n",
+                       fdctrl->dsr & FD_DSR_DRATEMASK, cur_drv->media_rate);
+        fdctrl_stop_transfer(fdctrl, FD_SR0_ABNTERM, FD_SR1_MA, 0x00);
+    } else {
+        fdctrl_stop_transfer(fdctrl, 0x00, 0x00, 0x00);
+    }
 }
 
 static void fdctrl_change_cb(void *opaque, bool load)
-- 
1.7.7.3