From: Axel Lin <axel.lin@gmail.com>
To: linux-kernel@vger.kernel.org
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>,
Liam Girdwood <lrg@ti.com>, Anuj Aggarwal <anuj.aggarwal@ti.com>
Subject: [PATCH RFC/RFT 7/7] regulator: tps6507x: Use regulator_list_voltage_table()
Date: Sun, 20 May 2012 10:39:12 +0800 [thread overview]
Message-ID: <1337481552.7204.10.camel@phoenix> (raw)
In-Reply-To: <1337481021.7204.1.camel@phoenix>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
---
drivers/regulator/tps6507x-regulator.c | 100 ++++++++++++++------------------
1 files changed, 43 insertions(+), 57 deletions(-)
diff --git a/drivers/regulator/tps6507x-regulator.c b/drivers/regulator/tps6507x-regulator.c
index da38be1..c771e10 100644
--- a/drivers/regulator/tps6507x-regulator.c
+++ b/drivers/regulator/tps6507x-regulator.c
@@ -43,50 +43,50 @@
/* Number of total regulators available */
#define TPS6507X_NUM_REGULATOR (TPS6507X_NUM_DCDC + TPS6507X_NUM_LDO)
-/* Supported voltage values for regulators (in milliVolts) */
-static const u16 VDCDCx_VSEL_table[] = {
- 725, 750, 775, 800,
- 825, 850, 875, 900,
- 925, 950, 975, 1000,
- 1025, 1050, 1075, 1100,
- 1125, 1150, 1175, 1200,
- 1225, 1250, 1275, 1300,
- 1325, 1350, 1375, 1400,
- 1425, 1450, 1475, 1500,
- 1550, 1600, 1650, 1700,
- 1750, 1800, 1850, 1900,
- 1950, 2000, 2050, 2100,
- 2150, 2200, 2250, 2300,
- 2350, 2400, 2450, 2500,
- 2550, 2600, 2650, 2700,
- 2750, 2800, 2850, 2900,
- 3000, 3100, 3200, 3300,
+/* Supported voltage values for regulators (in microVolts) */
+static const unsigned int VDCDCx_VSEL_table[] = {
+ 725000, 750000, 775000, 800000,
+ 825000, 850000, 875000, 900000,
+ 925000, 950000, 975000, 1000000,
+ 1025000, 1050000, 1075000, 1100000,
+ 1125000, 1150000, 1175000, 1200000,
+ 1225000, 1250000, 1275000, 1300000,
+ 1325000, 1350000, 1375000, 1400000,
+ 1425000, 1450000, 1475000, 1500000,
+ 1550000, 1600000, 1650000, 1700000,
+ 1750000, 1800000, 1850000, 1900000,
+ 1950000, 2000000, 2050000, 2100000,
+ 2150000, 2200000, 2250000, 2300000,
+ 2350000, 2400000, 2450000, 2500000,
+ 2550000, 2600000, 2650000, 2700000,
+ 2750000, 2800000, 2850000, 2900000,
+ 3000000, 3100000, 3200000, 3300000,
};
-static const u16 LDO1_VSEL_table[] = {
- 1000, 1100, 1200, 1250,
- 1300, 1350, 1400, 1500,
- 1600, 1800, 2500, 2750,
- 2800, 3000, 3100, 3300,
+static const unsigned int LDO1_VSEL_table[] = {
+ 1000000, 1100000, 1200000, 1250000,
+ 1300000, 1350000, 1400000, 1500000,
+ 1600000, 1800000, 2500000, 2750000,
+ 2800000, 3000000, 3100000, 3300000,
};
-static const u16 LDO2_VSEL_table[] = {
- 725, 750, 775, 800,
- 825, 850, 875, 900,
- 925, 950, 975, 1000,
- 1025, 1050, 1075, 1100,
- 1125, 1150, 1175, 1200,
- 1225, 1250, 1275, 1300,
- 1325, 1350, 1375, 1400,
- 1425, 1450, 1475, 1500,
- 1550, 1600, 1650, 1700,
- 1750, 1800, 1850, 1900,
- 1950, 2000, 2050, 2100,
- 2150, 2200, 2250, 2300,
- 2350, 2400, 2450, 2500,
- 2550, 2600, 2650, 2700,
- 2750, 2800, 2850, 2900,
- 3000, 3100, 3200, 3300,
+static const unsigned int LDO2_VSEL_table[] = {
+ 725000, 750000, 775000, 800000,
+ 825000, 850000, 875000, 900000,
+ 925000, 950000, 975000, 1000000,
+ 1025000, 1050000, 1075000, 1100000,
+ 1125000, 1150000, 1175000, 1200000,
+ 1225000, 1250000, 1275000, 1300000,
+ 1325000, 1350000, 1375000, 1400000,
+ 1425000, 1450000, 1475000, 1500000,
+ 1550000, 1600000, 1650000, 1700000,
+ 1750000, 1800000, 1850000, 1900000,
+ 1950000, 2000000, 2050000, 2100000,
+ 2150000, 2200000, 2250000, 2300000,
+ 2350000, 2400000, 2450000, 2500000,
+ 2550000, 2600000, 2650000, 2700000,
+ 2750000, 2800000, 2850000, 2900000,
+ 3000000, 3100000, 3200000, 3300000,
};
struct tps_info {
@@ -94,7 +94,7 @@ struct tps_info {
unsigned min_uV;
unsigned max_uV;
u8 table_len;
- const u16 *table;
+ const unsigned int *table;
/* Does DCDC high or the low register defines output voltage? */
bool defdcdc_default;
@@ -375,28 +375,13 @@ static int tps6507x_pmic_set_voltage_sel(struct regulator_dev *dev,
return tps6507x_pmic_reg_write(tps, reg, data);
}
-static int tps6507x_pmic_list_voltage(struct regulator_dev *dev,
- unsigned selector)
-{
- struct tps6507x_pmic *tps = rdev_get_drvdata(dev);
- int rid = rdev_get_id(dev);
-
- if (rid < TPS6507X_DCDC_1 || rid > TPS6507X_LDO_2)
- return -EINVAL;
-
- if (selector >= tps->info[rid]->table_len)
- return -EINVAL;
- else
- return tps->info[rid]->table[selector] * 1000;
-}
-
static struct regulator_ops tps6507x_pmic_ops = {
.is_enabled = tps6507x_pmic_is_enabled,
.enable = tps6507x_pmic_enable,
.disable = tps6507x_pmic_disable,
.get_voltage_sel = tps6507x_pmic_get_voltage_sel,
.set_voltage_sel = tps6507x_pmic_set_voltage_sel,
- .list_voltage = tps6507x_pmic_list_voltage,
+ .list_voltage = regulator_list_voltage_table,
};
static __devinit int tps6507x_pmic_probe(struct platform_device *pdev)
@@ -449,6 +434,7 @@ static __devinit int tps6507x_pmic_probe(struct platform_device *pdev)
tps->desc[i].name = info->name;
tps->desc[i].id = i;
tps->desc[i].n_voltages = info->table_len;
+ tps->desc[i].volt_table = info->table;
tps->desc[i].ops = &tps6507x_pmic_ops;
tps->desc[i].type = REGULATOR_VOLTAGE;
tps->desc[i].owner = THIS_MODULE;
--
1.7.5.4
next prev parent reply other threads:[~2012-05-20 2:41 UTC|newest]
Thread overview: 12+ messages / expand[flat|nested] mbox.gz Atom feed top
2012-05-20 2:30 [PATCH RFC/RFT 1/7] regulator: core: Allow drivers to set voltage mapping table in regulator_desc Axel Lin
2012-05-20 2:31 ` [PATCH RFC/RFT 2/7] regulator: ab3100: Use regulator_list_voltage_table() Axel Lin
2012-05-21 9:16 ` Linus Walleij
2012-05-20 2:33 ` [PATCH RFC/RFT 3/7] regulator: ab8500: " Axel Lin
2012-05-21 10:43 ` Linus Walleij
2012-05-21 11:17 ` Mark Brown
2012-05-20 2:34 ` [PATCH RFC/RFT 4/7] regulator: lp3971: " Axel Lin
2012-05-20 2:36 ` [PATCH RFC/RFT 5/7] regulator: lp3972: " Axel Lin
2012-05-20 2:37 ` [PATCH RFC/RFT 6/7] regulator: tps6105x: " Axel Lin
2012-05-21 16:06 ` Linus Walleij
2012-05-20 2:39 ` Axel Lin [this message]
2012-05-20 21:48 ` [PATCH RFC/RFT 1/7] regulator: core: Allow drivers to set voltage mapping table in regulator_desc Mark Brown
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1337481552.7204.10.camel@phoenix \
--to=axel.lin@gmail.com \
--cc=anuj.aggarwal@ti.com \
--cc=broonie@opensource.wolfsonmicro.com \
--cc=linux-kernel@vger.kernel.org \
--cc=lrg@ti.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.