From: Axel Lin <axel.lin@ingics.com>
To: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: David Dajun Chen <dchen@diasemi.com>,
Ashish Jangam <ashish.jangam@kpitcummins.com>,
Liam Girdwood <lrg@ti.com>,
linux-kernel@vger.kernel.org
Subject: [RFC/RFT][PATCH 2/4] regulator: da9055: Use linear_min_sel and regulator_[map|list]_voltage_linear
Date: Tue, 27 Nov 2012 10:26:14 +0800 [thread overview]
Message-ID: <1353983174.5422.4.camel@phoenix> (raw)
In-Reply-To: <1353983073.5422.2.camel@phoenix>
Signed-off-by: Axel Lin <axel.lin@ingics.com>
---
drivers/regulator/da9055-regulator.c | 55 +++++-----------------------------
1 file changed, 8 insertions(+), 47 deletions(-)
diff --git a/drivers/regulator/da9055-regulator.c b/drivers/regulator/da9055-regulator.c
index db59ce7..a4b9cb8 100644
--- a/drivers/regulator/da9055-regulator.c
+++ b/drivers/regulator/da9055-regulator.c
@@ -57,7 +57,6 @@ struct da9055_volt_reg {
int reg_a;
int reg_b;
int sl_shift;
- int v_offset;
int v_mask;
int v_shift;
};
@@ -201,41 +200,6 @@ static int da9055_buck_set_current_limit(struct regulator_dev *rdev, int min_uA,
return -EINVAL;
}
-static int da9055_list_voltage(struct regulator_dev *rdev, unsigned selector)
-{
- struct da9055_regulator *regulator = rdev_get_drvdata(rdev);
- struct da9055_regulator_info *info = regulator->info;
-
- if (selector >= rdev->desc->n_voltages)
- return -EINVAL;
-
- if (selector < info->volt.v_offset)
- return 0;
-
- selector -= info->volt.v_offset;
- return rdev->desc->min_uV + (rdev->desc->uV_step * selector);
-}
-
-static int da9055_map_voltage(struct regulator_dev *rdev, int min_uV,
- int max_uV)
-{
- struct da9055_regulator *regulator = rdev_get_drvdata(rdev);
- struct da9055_regulator_info *info = regulator->info;
- int sel, voltage;
-
- if (min_uV < rdev->desc->min_uV)
- min_uV = rdev->desc->min_uV;
-
- sel = DIV_ROUND_UP(min_uV - rdev->desc->min_uV, rdev->desc->uV_step);
- sel += info->volt.v_offset;
-
- voltage = da9055_list_voltage(rdev, sel);
- if (voltage < min_uV || voltage > max_uV)
- return -EINVAL;
-
- return sel;
-}
-
static int da9055_regulator_get_voltage_sel(struct regulator_dev *rdev)
{
struct da9055_regulator *regulator = rdev_get_drvdata(rdev);
@@ -264,10 +228,7 @@ static int da9055_regulator_get_voltage_sel(struct regulator_dev *rdev)
return ret;
sel = (ret & volt.v_mask);
- if (sel <= volt.v_offset)
- return 0;
- else
- return sel;
+ return sel;
}
static int da9055_regulator_set_voltage_sel(struct regulator_dev *rdev,
@@ -328,7 +289,7 @@ static int da9055_regulator_set_suspend_voltage(struct regulator_dev *rdev,
return ret;
}
- ret = da9055_map_voltage(rdev, uV, uV);
+ ret = regulator_map_voltage_linear(rdev, uV, uV);
if (ret < 0)
return ret;
@@ -371,8 +332,8 @@ static struct regulator_ops da9055_buck_ops = {
.get_voltage_sel = da9055_regulator_get_voltage_sel,
.set_voltage_sel = da9055_regulator_set_voltage_sel,
- .list_voltage = da9055_list_voltage,
- .map_voltage = da9055_map_voltage,
+ .list_voltage = regulator_list_voltage_linear,
+ .map_voltage = regulator_map_voltage_linear,
.is_enabled = regulator_is_enabled_regmap,
.enable = regulator_enable_regmap,
.disable = regulator_disable_regmap,
@@ -389,8 +350,8 @@ static struct regulator_ops da9055_ldo_ops = {
.get_voltage_sel = da9055_regulator_get_voltage_sel,
.set_voltage_sel = da9055_regulator_set_voltage_sel,
- .list_voltage = da9055_list_voltage,
- .map_voltage = da9055_map_voltage,
+ .list_voltage = regulator_list_voltage_linear,
+ .map_voltage = regulator_map_voltage_linear,
.is_enabled = regulator_is_enabled_regmap,
.enable = regulator_enable_regmap,
.disable = regulator_disable_regmap,
@@ -414,6 +375,7 @@ static struct regulator_ops da9055_ldo_ops = {
.enable_mask = 1, \
.min_uV = (min) * 1000,\
.uV_step = (step) * 1000,\
+ .linear_min_sel = (voffset),\
.owner = THIS_MODULE,\
},\
.conf = {\
@@ -425,7 +387,6 @@ static struct regulator_ops da9055_ldo_ops = {
.reg_a = DA9055_REG_VBCORE_A + DA9055_ID_##_id, \
.reg_b = DA9055_REG_VBCORE_B + DA9055_ID_##_id, \
.sl_shift = 7,\
- .v_offset = (voffset),\
.v_mask = (1 << (vbits)) - 1,\
.v_shift = (vbits),\
},\
@@ -443,6 +404,7 @@ static struct regulator_ops da9055_ldo_ops = {
.enable_mask = 1,\
.min_uV = (min) * 1000,\
.uV_step = (step) * 1000,\
+ .linear_min_sel = (voffset),\
.owner = THIS_MODULE,\
},\
.conf = {\
@@ -454,7 +416,6 @@ static struct regulator_ops da9055_ldo_ops = {
.reg_a = DA9055_REG_VBCORE_A + DA9055_ID_##_id, \
.reg_b = DA9055_REG_VBCORE_B + DA9055_ID_##_id, \
.sl_shift = 7,\
- .v_offset = (voffset),\
.v_mask = (1 << (vbits)) - 1,\
.v_shift = (vbits),\
},\
--
1.7.9.5
next prev parent reply other threads:[~2012-11-27 2:26 UTC|newest]
Thread overview: 6+ messages / expand[flat|nested] mbox.gz Atom feed top
2012-11-27 2:24 [RFC/RFT][PATCH 1/4] regulator: core: Allow specific minimal selector for starting linear mapping Axel Lin
2012-11-27 2:26 ` Axel Lin [this message]
2012-11-27 2:27 ` [RFC/RFT][PATCH 3/4] regulator: palmas: Use linear_min_sel and regulator_[map|list]_voltage_linear Axel Lin
2012-11-27 2:28 ` [RFC/RFT][PATCH 4/4] regulator: tps51632: " Axel Lin
2012-11-27 20:14 ` Mark Brown
2012-11-27 20:15 ` [RFC/RFT][PATCH 1/4] regulator: core: Allow specific minimal selector for starting linear mapping Mark Brown
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1353983174.5422.4.camel@phoenix \
--to=axel.lin@ingics.com \
--cc=ashish.jangam@kpitcummins.com \
--cc=broonie@opensource.wolfsonmicro.com \
--cc=dchen@diasemi.com \
--cc=linux-kernel@vger.kernel.org \
--cc=lrg@ti.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.