All of lore.kernel.org
 help / color / mirror / Atom feed
From: Axel Lin <axel.lin@ingics.com>
To: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>,
	Liam Girdwood <lrg@ti.com>,
	linux-kernel@vger.kernel.org
Subject: [PATCH 1/2] regulator: lp3971: Convert to get_voltage_sel
Date: Mon, 10 Dec 2012 19:46:52 +0800	[thread overview]
Message-ID: <1355140012.6601.1.camel@phoenix> (raw)

regulator_list_voltage_table() returns -EINVAL if selector >= n_voltages.
Thus we don't need to check if reg is greater than BUCK_TARGET_VOL_MAX_IDX in
lp3971_dcdc_get_voltage_sel.

BUCK_TARGET_VOL_MIN_IDX and BUCK_TARGET_VOL_MAX_IDX are not used, remove them.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
---
 drivers/regulator/lp3971.c |   22 ++++++----------------
 1 file changed, 6 insertions(+), 16 deletions(-)

diff --git a/drivers/regulator/lp3971.c b/drivers/regulator/lp3971.c
index 5f68ff1..9cb2c0f 100644
--- a/drivers/regulator/lp3971.c
+++ b/drivers/regulator/lp3971.c
@@ -73,8 +73,6 @@ static const unsigned int buck_voltage_map[] = {
 };
 
 #define BUCK_TARGET_VOL_MASK 0x3f
-#define BUCK_TARGET_VOL_MIN_IDX 0x01
-#define BUCK_TARGET_VOL_MAX_IDX 0x19
 
 #define LP3971_BUCK_RAMP_REG(x)	(buck_base_addr[x]+2)
 
@@ -140,7 +138,7 @@ static int lp3971_ldo_disable(struct regulator_dev *dev)
 	return lp3971_set_bits(lp3971, LP3971_LDO_ENABLE_REG, mask, 0);
 }
 
-static int lp3971_ldo_get_voltage(struct regulator_dev *dev)
+static int lp3971_ldo_get_voltage_sel(struct regulator_dev *dev)
 {
 	struct lp3971 *lp3971 = rdev_get_drvdata(dev);
 	int ldo = rdev_get_id(dev) - LP3971_LDO1;
@@ -149,7 +147,7 @@ static int lp3971_ldo_get_voltage(struct regulator_dev *dev)
 	reg = lp3971_reg_read(lp3971, LP3971_LDO_VOL_CONTR_REG(ldo));
 	val = (reg >> LDO_VOL_CONTR_SHIFT(ldo)) & LDO_VOL_CONTR_MASK;
 
-	return dev->desc->volt_table[val];
+	return val;
 }
 
 static int lp3971_ldo_set_voltage_sel(struct regulator_dev *dev,
@@ -168,7 +166,7 @@ static struct regulator_ops lp3971_ldo_ops = {
 	.is_enabled = lp3971_ldo_is_enabled,
 	.enable = lp3971_ldo_enable,
 	.disable = lp3971_ldo_disable,
-	.get_voltage = lp3971_ldo_get_voltage,
+	.get_voltage_sel = lp3971_ldo_get_voltage_sel,
 	.set_voltage_sel = lp3971_ldo_set_voltage_sel,
 };
 
@@ -201,24 +199,16 @@ static int lp3971_dcdc_disable(struct regulator_dev *dev)
 	return lp3971_set_bits(lp3971, LP3971_BUCK_VOL_ENABLE_REG, mask, 0);
 }
 
-static int lp3971_dcdc_get_voltage(struct regulator_dev *dev)
+static int lp3971_dcdc_get_voltage_sel(struct regulator_dev *dev)
 {
 	struct lp3971 *lp3971 = rdev_get_drvdata(dev);
 	int buck = rdev_get_id(dev) - LP3971_DCDC1;
 	u16 reg;
-	int val;
 
 	reg = lp3971_reg_read(lp3971, LP3971_BUCK_TARGET_VOL1_REG(buck));
 	reg &= BUCK_TARGET_VOL_MASK;
 
-	if (reg <= BUCK_TARGET_VOL_MAX_IDX)
-		val = buck_voltage_map[reg];
-	else {
-		val = 0;
-		dev_warn(&dev->dev, "chip reported incorrect voltage value.\n");
-	}
-
-	return val;
+	return reg;
 }
 
 static int lp3971_dcdc_set_voltage_sel(struct regulator_dev *dev,
@@ -249,7 +239,7 @@ static struct regulator_ops lp3971_dcdc_ops = {
 	.is_enabled = lp3971_dcdc_is_enabled,
 	.enable = lp3971_dcdc_enable,
 	.disable = lp3971_dcdc_disable,
-	.get_voltage = lp3971_dcdc_get_voltage,
+	.get_voltage_sel = lp3971_dcdc_get_voltage_sel,
 	.set_voltage_sel = lp3971_dcdc_set_voltage_sel,
 };
 
-- 
1.7.9.5




             reply	other threads:[~2012-12-10 11:47 UTC|newest]

Thread overview: 5+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2012-12-10 11:46 Axel Lin [this message]
2012-12-10 11:50 ` [PATCH 2/2] regulator: lp3972: Convert to get_voltage_sel Axel Lin
2012-12-24 16:28   ` Mark Brown
2012-12-11  7:16 ` [PATCH 1/2] regulator: lp3971: " Marek Szyprowski
2012-12-24 16:27 ` Mark Brown

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=1355140012.6601.1.camel@phoenix \
    --to=axel.lin@ingics.com \
    --cc=broonie@opensource.wolfsonmicro.com \
    --cc=linux-kernel@vger.kernel.org \
    --cc=lrg@ti.com \
    --cc=m.szyprowski@samsung.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.