All of lore.kernel.org
 help / color / mirror / Atom feed
From: Peter Hurley <peter@hurleysoftware.com>
To: Neil Horman <nhorman@tuxdriver.com>
Cc: Cong Wang <xiyou.wangcong@gmail.com>, netdev@vger.kernel.org
Subject: Re: netconsole fun
Date: Tue, 11 Dec 2012 12:17:52 -0500	[thread overview]
Message-ID: <1355246272.2694.27.camel@thor> (raw)
In-Reply-To: <20121211164526.GB7481@neilslaptop.think-freely.org>

On Tue, 2012-12-11 at 11:45 -0500, Neil Horman wrote:
> On Tue, Dec 11, 2012 at 10:16:51AM -0500, Peter Hurley wrote:
> > On Tue, 2012-12-11 at 09:30 -0500, Neil Horman wrote:
> > > On Tue, Dec 11, 2012 at 09:19:52AM -0500, Peter Hurley wrote:
> > > > On Tue, 2012-12-11 at 04:51 +0000, Cong Wang wrote:
> > > > > On Mon, 10 Dec 2012 at 14:17 GMT, Peter Hurley <peter@hurleysoftware.com> wrote:
> > > > > > Now that netpoll has been disabled for slaved devices, is there a
> > > > > > recommended method of running netconsole on a machine that has a slaved
> > > > > > device?
> > > > > >
> > > > > 
> > > > > Yes, running it on the master device instead.
> > > > 
> > > > Thanks for the suggestion, but:
> > > > 
> > > > [ 0.000000] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-3.7.0-rc8-xeon ...... netconsole=@192.168.10.99/br0,30000@192.168.10.100/xx:xx:xx:xx:xx:xx
> > > > ...
> > > > [ 5.289869] netpoll: netconsole: local port 6665
> > > > [ 5.289885] netpoll: netconsole: local IP 192.168.10.99
> > > > [ 5.289892] netpoll: netconsole: interface 'br0'
> > > > [ 5.289898] netpoll: netconsole: remote port 30000
> > > > [ 5.289907] netpoll: netconsole: remote IP 192.168.10.100
> > > > [ 5.289914] netpoll: netconsole: remote ethernet address xx:xx:xx:xx:xx:xx
> > > > [ 5.289922] netpoll: netconsole: br0 doesn't exist, aborting
> > > > [ 5.289929] netconsole: cleaning up
> > > > ...
> > > > [ 9.392291] Bridge firewalling registered
> > > > [ 9.396805] device eth1 entered promiscuous mode
> > > > [ 9.418350] eth1:  setting full-duplex.
> > > > [ 9.421268] br0: port 1(eth1) entered forwarding state
> > > > [ 9.423354] br0: port 1(eth1) entered forwarding state
> > > > 
> > > > 
> > > > Is there a way to control or associate network device names prior to
> > > > udev renaming?
> > > > 
> > > That looks like a systemd problem (or more specifically a boot dependency
> > > problem).  You need to modify your netconsole unit/service file to start after
> > > all your networking is up.  NetworkManager provides a dummy service file for
> > > this purpose, called networkmanager-wait-online.service
> > 
> > Ok. So with a single physical network interface that will be bridged,
> > netconsole cannot used for kernel boot messages.
> > 
> > With a machine with multiple nics, is there a way to control device
> > naming so that the interface name to be used by netconsole specified on
> > the boot command line will actually corresponding to the intended
> > device. For example,
> > 
> > [ 0.000000] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-3.7.0-rc8-xeon ...... netconsole=@192.168.1.123/eth0,30000@192.168.1.139/xx:xx:xx:xx:xx:xx
> > ....
> > [ 4.092184] 3c59x: Donald Becker and others.
> > [ 4.092204] 0000:07:05.0: 3Com PCI 3c905C Tornado at ffffc9000186cf80.
> > [ 4.094035] tg3.c:v3.125 (September 26, 2012)
> > ....
> > [ 4.125038] tg3 0000:08:00.0 eth1: Tigon3 [partno(BCM95754) rev b002] (PCI Express) MAC address xx:xx:xx:xx:xx:xx
> > [ 4.125055] tg3 0000:08:00.0 eth1: attached PHY is 5787 (10/100/1000Base-T Ethernet) (WireSpeed[1], EEE[0])
> > [ 4.125062] tg3 0000:08:00.0 eth1: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] TSOcap[1]
> > [ 4.125068] tg3 0000:08:00.0 eth1: dma_rwctrl[76180000] dma_mask[64-bit]
> > 
> > This is attaching netconsole to the wrong device because bus
> > enumeration, and therefore load order, is not consistent from boot to
> > boot.
> > 
> No, theres no way to do that.  As you note device ennumeration isn't consistent
> accross boots, thats why udev creates rules to rename devices based on immutable
> (or semi-immutable) data, like mac addresses, or pci bus locations).  Once that
> happens, you'll have consistent names for your interfaces, and that work will be
> guaranteed to be done after networkmanager has finished opening all the
> interfaces that it needs (hence my suggestion to make netconsole service
> dependent on networkmanager service startup completing).
> 
> Neil

Thanks for all your help here, Neil. Very much appreciated.

Happy Holidays,
Peter Hurley

  reply	other threads:[~2012-12-11 17:18 UTC|newest]

Thread overview: 25+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2012-12-10 14:17 netconsole fun Peter Hurley
2012-12-11  4:51 ` Cong Wang
2012-12-11 14:19   ` Peter Hurley
2012-12-11 14:30     ` Neil Horman
2012-12-11 15:16       ` Peter Hurley
2012-12-11 16:45         ` Neil Horman
2012-12-11 17:17           ` Peter Hurley [this message]
2012-12-11 21:19             ` Neil Horman
2012-12-12 20:59           ` Peter Hurley
2012-12-13 10:33             ` Cong Wang
2012-12-13 12:36             ` Neil Horman
2012-12-13 14:49               ` Peter Hurley
2012-12-13 18:08                 ` Neil Horman
2012-12-13 19:27                   ` Peter Hurley
2012-12-13 21:17                     ` Neil Horman
2012-12-13 22:24                       ` Peter Hurley
2012-12-14 14:20                         ` Neil Horman
2012-12-15 14:13                           ` Peter Hurley
2012-12-17 14:20                             ` Neil Horman
2013-04-29 17:28                               ` Peter Hurley
2013-04-29 18:21                                 ` Neil Horman
2013-04-30  2:44                                   ` Cong Wang
2013-05-03 19:07                                   ` Peter Hurley
  -- strict thread matches above, loose matches on Subject: below --
2012-12-10 18:00 Peter Hurley
2013-05-05  0:59 Neil Horman

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=1355246272.2694.27.camel@thor \
    --to=peter@hurleysoftware.com \
    --cc=netdev@vger.kernel.org \
    --cc=nhorman@tuxdriver.com \
    --cc=xiyou.wangcong@gmail.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.