All of lore.kernel.org
 help / color / mirror / Atom feed
From: Axel Lin <axel.lin@ingics.com>
To: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>,
	Liam Girdwood <lrg@ti.com>,
	linux-kernel@vger.kernel.org
Subject: [PATCH v2 2/2] regulator: 88pm8607: Use apply_[reg|bit] with regmap based voltage_sel operations
Date: Mon, 24 Dec 2012 09:14:38 +0800	[thread overview]
Message-ID: <1356311678.4697.2.camel@phoenix> (raw)
In-Reply-To: <1356311618.4697.1.camel@phoenix>

Signed-off-by: Axel Lin <axel.lin@ingics.com>
---
 drivers/regulator/88pm8607.c |   38 ++++++--------------------------------
 1 file changed, 6 insertions(+), 32 deletions(-)

diff --git a/drivers/regulator/88pm8607.c b/drivers/regulator/88pm8607.c
index 5c4879a..a957e8c 100644
--- a/drivers/regulator/88pm8607.c
+++ b/drivers/regulator/88pm8607.c
@@ -30,8 +30,6 @@ struct pm8607_regulator_info {
 	unsigned int	*vol_table;
 	unsigned int	*vol_suspend;
 
-	int	update_reg;
-	int	update_bit;
 	int	slope_double;
 };
 
@@ -222,30 +220,6 @@ static int pm8607_list_voltage(struct regulator_dev *rdev, unsigned index)
 	return ret;
 }
 
-static int pm8607_set_voltage_sel(struct regulator_dev *rdev, unsigned selector)
-{
-	struct pm8607_regulator_info *info = rdev_get_drvdata(rdev);
-	uint8_t val;
-	int ret;
-
-	val = (uint8_t)(selector << (ffs(rdev->desc->vsel_mask) - 1));
-
-	ret = pm860x_set_bits(info->i2c, rdev->desc->vsel_reg,
-			      rdev->desc->vsel_mask, val);
-	if (ret)
-		return ret;
-	switch (info->desc.id) {
-	case PM8607_ID_BUCK1:
-	case PM8607_ID_BUCK2:
-	case PM8607_ID_BUCK3:
-		ret = pm860x_set_bits(info->i2c, info->update_reg,
-				      1 << info->update_bit,
-				      1 << info->update_bit);
-		break;
-	}
-	return ret;
-}
-
 static int pm8606_preg_enable(struct regulator_dev *rdev)
 {
 	struct pm8607_regulator_info *info = rdev_get_drvdata(rdev);
@@ -277,7 +251,7 @@ static int pm8606_preg_is_enabled(struct regulator_dev *rdev)
 
 static struct regulator_ops pm8607_regulator_ops = {
 	.list_voltage	= pm8607_list_voltage,
-	.set_voltage_sel = pm8607_set_voltage_sel,
+	.set_voltage_sel = regulator_set_voltage_sel_regmap,
 	.get_voltage_sel = regulator_get_voltage_sel_regmap,
 	.enable = regulator_enable_regmap,
 	.disable = regulator_disable_regmap,
@@ -314,11 +288,11 @@ static struct regulator_ops pm8606_preg_ops = {
 		.n_voltages = ARRAY_SIZE(vreg##_table),			\
 		.vsel_reg = PM8607_##vreg,				\
 		.vsel_mask = ARRAY_SIZE(vreg##_table) - 1,		\
+		.apply_reg = PM8607_##ureg,				\
+		.apply_bit = (ubit),					\
 		.enable_reg = PM8607_##ereg,				\
 		.enable_mask = 1 << (ebit),				\
 	},								\
-	.update_reg	= PM8607_##ureg,				\
-	.update_bit	= (ubit),					\
 	.slope_double	= (0),						\
 	.vol_table	= (unsigned int *)&vreg##_table,		\
 	.vol_suspend	= (unsigned int *)&vreg##_suspend_table,	\
@@ -344,9 +318,9 @@ static struct regulator_ops pm8606_preg_ops = {
 }
 
 static struct pm8607_regulator_info pm8607_regulator_info[] = {
-	PM8607_DVC(BUCK1, GO, 0, SUPPLIES_EN11, 0),
-	PM8607_DVC(BUCK2, GO, 1, SUPPLIES_EN11, 1),
-	PM8607_DVC(BUCK3, GO, 2, SUPPLIES_EN11, 2),
+	PM8607_DVC(BUCK1, GO, BIT(0), SUPPLIES_EN11, 0),
+	PM8607_DVC(BUCK2, GO, BIT(1), SUPPLIES_EN11, 1),
+	PM8607_DVC(BUCK3, GO, BIT(2), SUPPLIES_EN11, 2),
 
 	PM8607_LDO(1,         LDO1, 0, SUPPLIES_EN11, 3),
 	PM8607_LDO(2,         LDO2, 0, SUPPLIES_EN11, 4),
-- 
1.7.9.5




  reply	other threads:[~2012-12-24  1:14 UTC|newest]

Thread overview: 4+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2012-12-24  1:13 [PATCH 1/2] [PATCH] regulator: 88pm8607: Update update_bit for BUCK2 in pm8607_set_voltage_sel Axel Lin
2012-12-24  1:14 ` Axel Lin [this message]
2012-12-25  0:37   ` [PATCH v2 2/2] regulator: 88pm8607: Use apply_[reg|bit] with regmap based voltage_sel operations Haojian Zhuang
2012-12-27 17:29 ` [PATCH 1/2] [PATCH] regulator: 88pm8607: Update update_bit for BUCK2 in pm8607_set_voltage_sel Mark Brown

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=1356311678.4697.2.camel@phoenix \
    --to=axel.lin@ingics.com \
    --cc=broonie@opensource.wolfsonmicro.com \
    --cc=haojian.zhuang@gmail.com \
    --cc=linux-kernel@vger.kernel.org \
    --cc=lrg@ti.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.