From: Axel Lin <axel.lin@ingics.com>
To: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Thomas Abraham <thomas.abraham@linaro.org>,
Kyungmin Park <kyungmin.park@samsung.com>,
MyungJoo Ham <myungjoo.ham@samsung.com>,
Liam Girdwood <lrg@ti.com>,
linux-kernel@vger.kernel.org
Subject: [PATCH 1/3] regulator: max8997: Use uV in voltage_map_desc
Date: Fri, 28 Dec 2012 17:09:03 +0800 [thread overview]
Message-ID: <1356685743.27172.2.camel@phoenix> (raw)
Current code does integer division (min_vol = min_uV / 1000) before pass
min_vol to max8997_get_voltage_proper_val().
So it is possible min_vol is truncated to a smaller value.
For example, if the request min_uV is 800900 for ldo.
min_vol = 800900 / 1000 = 800 (mV)
Then max8997_get_voltage_proper_val returns 800 mV for this case which is lower
than the requested voltage.
Use uV rather than mV in voltage_map_desc to prevent truncation by integer
division.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
---
drivers/regulator/max8997.c | 36 +++++++++++++++++-------------------
1 file changed, 17 insertions(+), 19 deletions(-)
diff --git a/drivers/regulator/max8997.c b/drivers/regulator/max8997.c
index c30424a..1a1ae99 100644
--- a/drivers/regulator/max8997.c
+++ b/drivers/regulator/max8997.c
@@ -78,26 +78,26 @@ struct voltage_map_desc {
int step;
};
-/* Voltage maps in mV */
+/* Voltage maps in uV */
static const struct voltage_map_desc ldo_voltage_map_desc = {
- .min = 800, .max = 3950, .step = 50,
+ .min = 800000, .max = 3950000, .step = 50000,
}; /* LDO1 ~ 18, 21 all */
static const struct voltage_map_desc buck1245_voltage_map_desc = {
- .min = 650, .max = 2225, .step = 25,
+ .min = 650000, .max = 2225000, .step = 25000,
}; /* Buck1, 2, 4, 5 */
static const struct voltage_map_desc buck37_voltage_map_desc = {
- .min = 750, .max = 3900, .step = 50,
+ .min = 750000, .max = 3900000, .step = 50000,
}; /* Buck3, 7 */
-/* current map in mA */
+/* current map in uA */
static const struct voltage_map_desc charger_current_map_desc = {
- .min = 200, .max = 950, .step = 50,
+ .min = 200000, .max = 950000, .step = 50000,
};
static const struct voltage_map_desc topoff_current_map_desc = {
- .min = 50, .max = 200, .step = 10,
+ .min = 50000, .max = 200000, .step = 10000,
};
static const struct voltage_map_desc *reg_voltage_map[] = {
@@ -178,7 +178,7 @@ static int max8997_list_voltage(struct regulator_dev *rdev,
if (val > desc->max)
return -EINVAL;
- return val * 1000;
+ return val;
}
static int max8997_get_enable_register(struct regulator_dev *rdev,
@@ -469,7 +469,6 @@ static int max8997_set_voltage_ldobuck(struct regulator_dev *rdev,
{
struct max8997_data *max8997 = rdev_get_drvdata(rdev);
struct i2c_client *i2c = max8997->iodev->i2c;
- int min_vol = min_uV / 1000, max_vol = max_uV / 1000;
const struct voltage_map_desc *desc;
int rid = rdev_get_id(rdev);
int i, reg, shift, mask, ret;
@@ -493,7 +492,7 @@ static int max8997_set_voltage_ldobuck(struct regulator_dev *rdev,
desc = reg_voltage_map[rid];
- i = max8997_get_voltage_proper_val(desc, min_vol, max_vol);
+ i = max8997_get_voltage_proper_val(desc, min_uV, max_uV);
if (i < 0)
return i;
@@ -541,7 +540,7 @@ static int max8997_set_voltage_buck_time_sel(struct regulator_dev *rdev,
case MAX8997_BUCK4:
case MAX8997_BUCK5:
return DIV_ROUND_UP(desc->step * (new_selector - old_selector),
- max8997->ramp_delay);
+ max8997->ramp_delay * 1000);
}
return 0;
@@ -640,7 +639,6 @@ static int max8997_set_voltage_buck(struct regulator_dev *rdev,
const struct voltage_map_desc *desc;
int new_val, new_idx, damage, tmp_val, tmp_idx, tmp_dmg;
bool gpio_dvs_mode = false;
- int min_vol = min_uV / 1000, max_vol = max_uV / 1000;
if (rid < MAX8997_BUCK1 || rid > MAX8997_BUCK7)
return -EINVAL;
@@ -665,7 +663,7 @@ static int max8997_set_voltage_buck(struct regulator_dev *rdev,
selector);
desc = reg_voltage_map[rid];
- new_val = max8997_get_voltage_proper_val(desc, min_vol, max_vol);
+ new_val = max8997_get_voltage_proper_val(desc, min_uV, max_uV);
if (new_val < 0)
return new_val;
@@ -1080,8 +1078,8 @@ static int max8997_pmic_probe(struct platform_device *pdev)
max8997->buck1_vol[i] = ret =
max8997_get_voltage_proper_val(
&buck1245_voltage_map_desc,
- pdata->buck1_voltage[i] / 1000,
- pdata->buck1_voltage[i] / 1000 +
+ pdata->buck1_voltage[i],
+ pdata->buck1_voltage[i] +
buck1245_voltage_map_desc.step);
if (ret < 0)
goto err_out;
@@ -1089,8 +1087,8 @@ static int max8997_pmic_probe(struct platform_device *pdev)
max8997->buck2_vol[i] = ret =
max8997_get_voltage_proper_val(
&buck1245_voltage_map_desc,
- pdata->buck2_voltage[i] / 1000,
- pdata->buck2_voltage[i] / 1000 +
+ pdata->buck2_voltage[i],
+ pdata->buck2_voltage[i] +
buck1245_voltage_map_desc.step);
if (ret < 0)
goto err_out;
@@ -1098,8 +1096,8 @@ static int max8997_pmic_probe(struct platform_device *pdev)
max8997->buck5_vol[i] = ret =
max8997_get_voltage_proper_val(
&buck1245_voltage_map_desc,
- pdata->buck5_voltage[i] / 1000,
- pdata->buck5_voltage[i] / 1000 +
+ pdata->buck5_voltage[i],
+ pdata->buck5_voltage[i] +
buck1245_voltage_map_desc.step);
if (ret < 0)
goto err_out;
--
1.7.9.5
next reply other threads:[~2012-12-28 9:09 UTC|newest]
Thread overview: 6+ messages / expand[flat|nested] mbox.gz Atom feed top
2012-12-28 9:09 Axel Lin [this message]
2012-12-28 9:10 ` [PATCH 2/3] regulator: max8998: Use uV in voltage_map_desc Axel Lin
2013-01-08 11:16 ` Mark Brown
2012-12-28 9:14 ` [PATCH 3/3] regulator: max8998: Return enough delay time for max8998_set_voltage_buck_time_sel Axel Lin
2013-01-08 11:18 ` Mark Brown
2013-01-08 11:14 ` [PATCH 1/3] regulator: max8997: Use uV in voltage_map_desc Mark Brown
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1356685743.27172.2.camel@phoenix \
--to=axel.lin@ingics.com \
--cc=broonie@opensource.wolfsonmicro.com \
--cc=kyungmin.park@samsung.com \
--cc=linux-kernel@vger.kernel.org \
--cc=lrg@ti.com \
--cc=myungjoo.ham@samsung.com \
--cc=thomas.abraham@linaro.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.