From: Giuseppe Pagano <giuseppe.pagano@seco.com>
To: u-boot@lists.denx.de
Subject: [U-Boot] [PATCH 1/4] udoo: Add Ethernet support.
Date: Wed, 06 Nov 2013 21:33:06 +0100 [thread overview]
Message-ID: <1383769986.3741.15.camel@localhost> (raw)
Add Ethernet and networking support on uDoo board (FEC + phy Micrel)
Signed-off-by: Giuseppe Pagano <giuseppe.pagano@seco.com>
Cc: sbabic at denx.de
---
diff -uNr a/board/udoo/udoo.c b/board/udoo/udoo.c
--- a/board/udoo/udoo.c
+++ b/board/udoo/udoo.c
@@ -9,6 +9,7 @@
#include <asm/arch/clock.h>
#include <asm/arch/imx-regs.h>
#include <asm/arch/iomux.h>
+#include <malloc.h>
#include <asm/arch/mx6-pins.h>
#include <asm/errno.h>
#include <asm/gpio.h>
@@ -18,6 +19,9 @@
#include <asm/arch/crm_regs.h>
#include <asm/io.h>
#include <asm/arch/sys_proto.h>
+#include <micrel.h>
+#include <miiphy.h>
+#include <netdev.h>
DECLARE_GLOBAL_DATA_PTR;
@@ -25,6 +29,9 @@
PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | \
PAD_CTL_SRE_FAST | PAD_CTL_HYS)
+#define ENET_PAD_CTRL (PAD_CTL_PUS_100K_UP | \
+ PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS)
+
#define USDHC_PAD_CTRL (PAD_CTL_PUS_47K_UP | \
PAD_CTL_SPEED_LOW | PAD_CTL_DSE_80ohm | \
PAD_CTL_SRE_FAST | PAD_CTL_HYS)
@@ -58,6 +65,99 @@
MX6_PAD_EIM_D19__GPIO_3_19,
};
+int mx6_rgmii_rework(struct phy_device *phydev)
+{
+ /* To advertise only 10 Mbs */
+ phy_write(phydev, MDIO_DEVAD_NONE, 0x4, 0x61);
+ phy_write(phydev, MDIO_DEVAD_NONE, 0x9, 0x0c00);
+
+ /* enable master mode, force phy to 100Mbps */
+ phy_write(phydev, MDIO_DEVAD_NONE, 0x9, 0x1c00);
+
+ /* min rx data delay */
+ phy_write(phydev, MDIO_DEVAD_NONE, 0x0b, 0x8105);
+ phy_write(phydev, MDIO_DEVAD_NONE, 0x0c, 0x0000);
+
+ /* max rx/tx clock delay, min rx/tx control delay */
+ phy_write(phydev, MDIO_DEVAD_NONE, 0x0b, 0x8104);
+ phy_write(phydev, MDIO_DEVAD_NONE, 0x0c, 0xf0f0);
+ phy_write(phydev, MDIO_DEVAD_NONE, 0x0b, 0x104);
+
+ /* min rx data delay */
+ ksz9021_phy_extended_write(phydev,
+ MII_KSZ9021_EXT_RGMII_RX_DATA_SKEW, 0x0);
+ /* min tx data delay */
+ ksz9021_phy_extended_write(phydev,
+ MII_KSZ9021_EXT_RGMII_TX_DATA_SKEW, 0x0);
+ /* max rx/tx clock delay, min rx/tx control */
+ ksz9021_phy_extended_write(phydev,
+ MII_KSZ9021_EXT_RGMII_CLOCK_SKEW, 0x03FF);
+ return 0;
+}
+
+static iomux_v3_cfg_t const enet_pads1[] = {
+ MX6_PAD_ENET_MDIO__ENET_MDIO | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_ENET_MDC__ENET_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_RGMII_TXC__ENET_RGMII_TXC | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_RGMII_TD0__ENET_RGMII_TD0 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_RGMII_TD1__ENET_RGMII_TD1 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_RGMII_TD2__ENET_RGMII_TD2 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_RGMII_TD3__ENET_RGMII_TD3 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_RGMII_TX_CTL__RGMII_TX_CTL | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_ENET_REF_CLK__ENET_TX_CLK | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_RGMII_RXC__ENET_RGMII_RXC | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ /* RGMII reset */
+ MX6_PAD_EIM_D23__GPIO_3_23 | MUX_PAD_CTRL(NO_PAD_CTRL),
+ /* alimentazione ethernet*/
+ MX6_PAD_EIM_EB3__GPIO_2_31 | MUX_PAD_CTRL(NO_PAD_CTRL),
+ /* pin 32 - 1 - (MODE0) all */
+ MX6_PAD_RGMII_RD0__GPIO_6_25 | MUX_PAD_CTRL(NO_PAD_CTRL),
+ /* pin 31 - 1 - (MODE1) all */
+ MX6_PAD_RGMII_RD1__GPIO_6_27 | MUX_PAD_CTRL(NO_PAD_CTRL),
+ /* pin 28 - 1 - (MODE2) all */
+ MX6_PAD_RGMII_RD2__GPIO_6_28 | MUX_PAD_CTRL(NO_PAD_CTRL),
+ /* pin 27 - 1 - (MODE3) all */
+ MX6_PAD_RGMII_RD3__GPIO_6_29 | MUX_PAD_CTRL(NO_PAD_CTRL),
+ /* pin 33 - 1 - (CLK125_EN) 125Mhz clockout enabled */
+ MX6_PAD_RGMII_RX_CTL__GPIO_6_24 | MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
+static iomux_v3_cfg_t const enet_pads2[] = {
+ MX6_PAD_RGMII_RD0__ENET_RGMII_RD0 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_RGMII_RD1__ENET_RGMII_RD1 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_RGMII_RD2__ENET_RGMII_RD2 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_RGMII_RD3__ENET_RGMII_RD3 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_RGMII_RX_CTL__RGMII_RX_CTL | MUX_PAD_CTRL(ENET_PAD_CTRL),
+};
+
+static void setup_iomux_enet(void)
+{
+ imx_iomux_v3_setup_multiple_pads(enet_pads1, ARRAY_SIZE(enet_pads1));
+ udelay(20);
+ gpio_direction_output(IMX_GPIO_NR(2, 31), 1); /* Power on of enet */
+
+ gpio_direction_output(IMX_GPIO_NR(3, 23), 0); /* SABRE Lite PHY rst */
+
+ gpio_direction_output(IMX_GPIO_NR(6, 24), 1);
+ gpio_direction_output(IMX_GPIO_NR(6, 25), 1);
+ gpio_direction_output(IMX_GPIO_NR(6, 27), 1);
+ gpio_direction_output(IMX_GPIO_NR(6, 28), 1);
+ gpio_direction_output(IMX_GPIO_NR(6, 29), 1);
+ udelay(1000 * 10);
+
+ gpio_set_value(IMX_GPIO_NR(3, 23), 1); /* SABRE Lite PHY rst */
+ /* Need delay 100ms according to KSZ9031 spec */
+ udelay(1000 * 100);
+
+ gpio_free(IMX_GPIO_NR(6, 24));
+ gpio_free(IMX_GPIO_NR(6, 25));
+ gpio_free(IMX_GPIO_NR(6, 27));
+ gpio_free(IMX_GPIO_NR(6, 28));
+ gpio_free(IMX_GPIO_NR(6, 29));
+
+ imx_iomux_v3_setup_multiple_pads(enet_pads2, ARRAY_SIZE(enet_pads2));
+}
+
static void setup_iomux_uart(void)
{
imx_iomux_v3_setup_multiple_pads(uart2_pads,
ARRAY_SIZE(uart2_pads));
@@ -77,6 +177,37 @@
return 1; /* Always present */
}
+int board_eth_init(bd_t *bis)
+{
+ uint32_t base = IMX_FEC_BASE;
+ struct mii_dev *bus = NULL;
+ struct phy_device *phydev = NULL;
+ int ret;
+
+ setup_iomux_enet();
+
+#ifdef CONFIG_FEC_MXC
+ bus = fec_get_miibus(base, -1);
+ if (!bus)
+ return 0;
+ /* scan phy 4,5,6,7 */
+ phydev = phy_find_by_mask(bus, (0xf << 4), PHY_INTERFACE_MODE_RGMII);
+
+ if (!phydev) {
+ free(bus);
+ return 0;
+ }
+ printf("using phy@%d\n", phydev->addr);
+ ret = fec_probe(bis, -1, base, bus, phydev);
+ if (ret) {
+ printf("FEC MXC: %s:failed\n", __func__);
+ free(phydev);
+ free(bus);
+ }
+#endif
+ return 0;
+}
+
int board_mmc_init(bd_t *bis)
{
imx_iomux_v3_setup_multiple_pads(usdhc3_pads,
ARRAY_SIZE(usdhc3_pads));
@@ -94,6 +225,15 @@
return 0;
}
+int board_phy_config(struct phy_device *phydev)
+{
+ mx6_rgmii_rework(phydev);
+ if (phydev->drv->config)
+ phydev->drv->config(phydev);
+
+ return 0;
+}
+
int board_init(void)
{
/* address of boot parameters */
diff -uNr a/include/configs/udoo.h b/include/configs/udoo.h
--- a/include/configs/udoo.h
+++ b/include/configs/udoo.h
@@ -34,6 +34,22 @@
#define CONFIG_MXC_UART
#define CONFIG_MXC_UART_BASE UART2_BASE
+/* Network support */
+
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_NET
+#define CONFIG_FEC_MXC
+#define CONFIG_MII
+#define IMX_FEC_BASE ENET_BASE_ADDR
+#define CONFIG_FEC_XCV_TYPE RGMII
+#define CONFIG_ETHPRIME "FEC"
+#define CONFIG_FEC_MXC_PHYADDR 6
+#define CONFIG_PHYLIB
+#define CONFIG_PHY_MICREL
+#define CONFIG_PHY_MICREL_KSZ9021
+
/* allow to overwrite serial and ethaddr */
#define CONFIG_ENV_OVERWRITE
#define CONFIG_CONS_INDEX 1
next reply other threads:[~2013-11-06 20:33 UTC|newest]
Thread overview: 6+ messages / expand[flat|nested] mbox.gz Atom feed top
2013-11-06 20:33 Giuseppe Pagano [this message]
2013-11-07 8:38 ` [U-Boot] [PATCH 1/4] udoo: Add Ethernet support Stefano Babic
2013-11-07 12:37 ` Giuseppe Pagano
2013-11-07 14:57 ` Stefano Babic
2013-11-07 14:58 ` Stefano Babic
2013-11-07 15:28 ` Joe Hershberger
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1383769986.3741.15.camel@localhost \
--to=giuseppe.pagano@seco.com \
--cc=u-boot@lists.denx.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.