All of lore.kernel.org
 help / color / mirror / Atom feed
From: jeff.mcgee@intel.com
To: intel-gfx@lists.freedesktop.org
Subject: [PATCH v2] drm/i915: Restore rps/rc6 on reset
Date: Tue,  4 Feb 2014 11:32:31 -0600	[thread overview]
Message-ID: <1391535151-28067-1-git-send-email-jeff.mcgee@intel.com> (raw)
In-Reply-To: <1383766838.2524.19.camel@jeffdesk>

From: Jeff McGee <jeff.mcgee@intel.com>

A check of rps/rc6 state after i915_reset determined that the ring
MAX_IDLE registers were returned to their hardware defaults and that
the GEN6_PMIMR register was set to mask all interrupts. This change
restores those values to their pre-reset states by re-initializing
rps/rc6 in i915_reset. A full re-initialization was opted for versus
a targeted set of restore operations for simplicity and maintain-
ability. Note that the re-initialization is not done for Ironlake,
due to a past comment that it causes problems.

Also updated the rps initialization sequence to preserve existing
min/max values in the case of a re-init. We assume the values were
validated upon being set and do not do further range checking. The
debugfs interface for changing min/max was updated with range
checking to ensure this condition (already present in sysfs
interface).

v2: fix rps logging to output hw_max and hw_min, not rps.max_delay
    and rps.min_delay which don't strictly represent hardware limits.
    Add igt testcase to signed-off-by section.

Testcase: igt/pm_rps/reset
Signed-off-by: Jeff McGee <jeff.mcgee@intel.com>
---
 drivers/gpu/drm/i915/i915_debugfs.c | 49 +++++++++++++++++++++++++++++++------
 drivers/gpu/drm/i915/i915_drv.c     | 11 +++++++++
 drivers/gpu/drm/i915/intel_pm.c     | 35 +++++++++++++++++---------
 3 files changed, 76 insertions(+), 19 deletions(-)

diff --git a/drivers/gpu/drm/i915/i915_debugfs.c b/drivers/gpu/drm/i915/i915_debugfs.c
index bc8707f..2dc05c3 100644
--- a/drivers/gpu/drm/i915/i915_debugfs.c
+++ b/drivers/gpu/drm/i915/i915_debugfs.c
@@ -3223,6 +3223,7 @@ i915_max_freq_set(void *data, u64 val)
 {
 	struct drm_device *dev = data;
 	struct drm_i915_private *dev_priv = dev->dev_private;
+	u32 rp_state_cap, hw_max, hw_min;
 	int ret;
 
 	if (!(IS_GEN6(dev) || IS_GEN7(dev)))
@@ -3241,14 +3242,29 @@ i915_max_freq_set(void *data, u64 val)
 	 */
 	if (IS_VALLEYVIEW(dev)) {
 		val = vlv_freq_opcode(dev_priv, val);
-		dev_priv->rps.max_delay = val;
-		valleyview_set_rps(dev, val);
+
+		hw_max = valleyview_rps_max_freq(dev_priv);
+		hw_min = valleyview_rps_min_freq(dev_priv);
 	} else {
 		do_div(val, GT_FREQUENCY_MULTIPLIER);
-		dev_priv->rps.max_delay = val;
-		gen6_set_rps(dev, val);
+
+		rp_state_cap = I915_READ(GEN6_RP_STATE_CAP);
+		hw_max = dev_priv->rps.hw_max;
+		hw_min = (rp_state_cap >> 16) & 0xff;
+	}
+
+	if (val < hw_min || val > hw_max || val < dev_priv->rps.min_delay) {
+		mutex_unlock(&dev_priv->rps.hw_lock);
+		return -EINVAL;
 	}
 
+	dev_priv->rps.max_delay = val;
+
+	if (IS_VALLEYVIEW(dev))
+		valleyview_set_rps(dev, val);
+	else
+		gen6_set_rps(dev, val);
+
 	mutex_unlock(&dev_priv->rps.hw_lock);
 
 	return 0;
@@ -3288,6 +3304,7 @@ i915_min_freq_set(void *data, u64 val)
 {
 	struct drm_device *dev = data;
 	struct drm_i915_private *dev_priv = dev->dev_private;
+	u32 rp_state_cap, hw_max, hw_min;
 	int ret;
 
 	if (!(IS_GEN6(dev) || IS_GEN7(dev)))
@@ -3306,13 +3323,29 @@ i915_min_freq_set(void *data, u64 val)
 	 */
 	if (IS_VALLEYVIEW(dev)) {
 		val = vlv_freq_opcode(dev_priv, val);
-		dev_priv->rps.min_delay = val;
-		valleyview_set_rps(dev, val);
+
+		hw_max = valleyview_rps_max_freq(dev_priv);
+		hw_min = valleyview_rps_min_freq(dev_priv);
 	} else {
 		do_div(val, GT_FREQUENCY_MULTIPLIER);
-		dev_priv->rps.min_delay = val;
-		gen6_set_rps(dev, val);
+
+		rp_state_cap = I915_READ(GEN6_RP_STATE_CAP);
+		hw_max = dev_priv->rps.hw_max;
+		hw_min = (rp_state_cap >> 16) & 0xff;
+	}
+
+	if (val < hw_min || val > hw_max || val > dev_priv->rps.max_delay) {
+		mutex_unlock(&dev_priv->rps.hw_lock);
+		return -EINVAL;
 	}
+
+	dev_priv->rps.min_delay = val;
+
+	if (IS_VALLEYVIEW(dev))
+		valleyview_set_rps(dev, val);
+	else
+		gen6_set_rps(dev, val);
+
 	mutex_unlock(&dev_priv->rps.hw_lock);
 
 	return 0;
diff --git a/drivers/gpu/drm/i915/i915_drv.c b/drivers/gpu/drm/i915/i915_drv.c
index a071748..2449364 100644
--- a/drivers/gpu/drm/i915/i915_drv.c
+++ b/drivers/gpu/drm/i915/i915_drv.c
@@ -691,6 +691,17 @@ int i915_reset(struct drm_device *dev)
 
 		drm_irq_uninstall(dev);
 		drm_irq_install(dev);
+
+		/* rps/rc6 re-init is necessary to restore state lost after the
+		 * reset and the re-install of drm irq. Skip for ironlake per
+		 * previous concerns that it doesn't respond well to some forms
+		 * of re-init after reset. */
+		if (INTEL_INFO(dev)->gen > 5) {
+			mutex_lock(&dev->struct_mutex);
+			intel_enable_gt_powersave(dev);
+			mutex_unlock(&dev->struct_mutex);
+		}
+
 		intel_hpd_init(dev);
 	} else {
 		mutex_unlock(&dev->struct_mutex);
diff --git a/drivers/gpu/drm/i915/intel_pm.c b/drivers/gpu/drm/i915/intel_pm.c
index 9ab3883..6af58cd 100644
--- a/drivers/gpu/drm/i915/intel_pm.c
+++ b/drivers/gpu/drm/i915/intel_pm.c
@@ -3322,7 +3322,7 @@ static void gen6_enable_rps(struct drm_device *dev)
 {
 	struct drm_i915_private *dev_priv = dev->dev_private;
 	struct intel_ring_buffer *ring;
-	u32 rp_state_cap;
+	u32 rp_state_cap, hw_max, hw_min;
 	u32 gt_perf_status;
 	u32 rc6vids, pcu_mbox, rc6_mask = 0;
 	u32 gtfifodbg;
@@ -3351,13 +3351,20 @@ static void gen6_enable_rps(struct drm_device *dev)
 	gt_perf_status = I915_READ(GEN6_GT_PERF_STATUS);
 
 	/* In units of 50MHz */
-	dev_priv->rps.hw_max = dev_priv->rps.max_delay = rp_state_cap & 0xff;
-	dev_priv->rps.min_delay = (rp_state_cap >> 16) & 0xff;
+	dev_priv->rps.hw_max = hw_max = rp_state_cap & 0xff;
+	hw_min = (rp_state_cap >> 16) & 0xff;
 	dev_priv->rps.rp1_delay = (rp_state_cap >>  8) & 0xff;
 	dev_priv->rps.rp0_delay = (rp_state_cap >>  0) & 0xff;
 	dev_priv->rps.rpe_delay = dev_priv->rps.rp1_delay;
 	dev_priv->rps.cur_delay = 0;
 
+	/* Preserve min/max settings in case of re-init */
+	if (dev_priv->rps.max_delay == 0)
+		dev_priv->rps.max_delay = hw_max;
+
+	if (dev_priv->rps.min_delay == 0)
+		dev_priv->rps.min_delay = hw_min;
+
 	/* disable the counters and set deterministic thresholds */
 	I915_WRITE(GEN6_RC_CONTROL, 0);
 
@@ -3586,7 +3593,7 @@ static void valleyview_enable_rps(struct drm_device *dev)
 {
 	struct drm_i915_private *dev_priv = dev->dev_private;
 	struct intel_ring_buffer *ring;
-	u32 gtfifodbg, val, rc6_mode = 0;
+	u32 gtfifodbg, val, hw_max, hw_min, rc6_mode = 0;
 	int i;
 
 	WARN_ON(!mutex_is_locked(&dev_priv->rps.hw_lock));
@@ -3648,21 +3655,27 @@ static void valleyview_enable_rps(struct drm_device *dev)
 			 vlv_gpu_freq(dev_priv, dev_priv->rps.cur_delay),
 			 dev_priv->rps.cur_delay);
 
-	dev_priv->rps.max_delay = valleyview_rps_max_freq(dev_priv);
-	dev_priv->rps.hw_max = dev_priv->rps.max_delay;
+	dev_priv->rps.hw_max = hw_max = valleyview_rps_max_freq(dev_priv);
 	DRM_DEBUG_DRIVER("max GPU freq: %d MHz (%u)\n",
-			 vlv_gpu_freq(dev_priv, dev_priv->rps.max_delay),
-			 dev_priv->rps.max_delay);
+			 vlv_gpu_freq(dev_priv, hw_max),
+			 hw_max);
 
 	dev_priv->rps.rpe_delay = valleyview_rps_rpe_freq(dev_priv);
 	DRM_DEBUG_DRIVER("RPe GPU freq: %d MHz (%u)\n",
 			 vlv_gpu_freq(dev_priv, dev_priv->rps.rpe_delay),
 			 dev_priv->rps.rpe_delay);
 
-	dev_priv->rps.min_delay = valleyview_rps_min_freq(dev_priv);
+	hw_min = valleyview_rps_min_freq(dev_priv);
 	DRM_DEBUG_DRIVER("min GPU freq: %d MHz (%u)\n",
-			 vlv_gpu_freq(dev_priv, dev_priv->rps.min_delay),
-			 dev_priv->rps.min_delay);
+			 vlv_gpu_freq(dev_priv, hw_min),
+			 hw_min);
+
+	/* Preserve min/max settings in case of re-init */
+	if (dev_priv->rps.max_delay == 0)
+		dev_priv->rps.max_delay = hw_max;
+
+	if (dev_priv->rps.min_delay == 0)
+		dev_priv->rps.min_delay = hw_min;
 
 	DRM_DEBUG_DRIVER("setting GPU freq to %d MHz (%u)\n",
 			 vlv_gpu_freq(dev_priv, dev_priv->rps.rpe_delay),
-- 
1.8.5.2

  reply	other threads:[~2014-02-04 17:25 UTC|newest]

Thread overview: 9+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2013-10-31 19:52 [PATCH] drm/i915: Restore rps/rc6 on reset jeff.mcgee
2013-10-31 19:52 ` jeff.mcgee
2013-11-04  8:44   ` Daniel Vetter
2013-11-05 20:38     ` Mcgee, Jeff
2013-11-06 19:37       ` Mcgee, Jeff
2014-02-04 17:32         ` jeff.mcgee [this message]
2014-02-07  9:25           ` [PATCH v2] " Daniel Vetter
2013-11-01 10:47 ` [PATCH] " Jani Nikula
2013-11-01 11:05   ` Daniel Vetter

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=1391535151-28067-1-git-send-email-jeff.mcgee@intel.com \
    --to=jeff.mcgee@intel.com \
    --cc=intel-gfx@lists.freedesktop.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.