[PATCH] Makefile: default to -lcurl when no CURL_CONFIG or CURLDIR

[Dave Borowitz <dborowitz@google.com>]

The original implementation of CURL_CONFIG support did not match the
original behavior of using -lcurl when CURLDIR was not set. This broke
implementations that were lacking curl-config but did have libcurl
installed along system libraries, such as MSysGit. In other words, the
assumption that curl-config is always installed was incorrect.

Instead, if CURL_CONFIG is empty or returns an empty result (e.g. due
to curl-config being missing), use the old behavior of falling back to
-lcurl.
---
 Makefile | 36 +++++++++++++++++++++++++-----------
 1 file changed, 25 insertions(+), 11 deletions(-)

diff --git a/Makefile b/Makefile
index 74a929b..79b7442 100644
--- a/Makefile
+++ b/Makefile
@@ -35,7 +35,9 @@ all::
 # transports (neither smart nor dumb).
 #
 # Define CURL_CONFIG to the path to a curl-config binary other than the
-# default 'curl-config'.
+# default 'curl-config'. If CURL_CONFIG is unset or points to a binary that
+# is not found, defaults to the CURLDIR behavior, or if CURLDIR is not set,
+# uses -lcurl with no additional library detection.
 #
 # Define CURL_STATIC to statically link libcurl.  Only applies if
 # CURL_CONFIG is used.
@@ -1127,9 +1129,27 @@ ifdef NO_CURL
 	REMOTE_CURL_NAMES =
 else
 	ifdef CURLDIR
-		# Try "-Wl,-rpath=$(CURLDIR)/$(lib)" in such a case.
-		BASIC_CFLAGS += -I$(CURLDIR)/include
-		CURL_LIBCURL = -L$(CURLDIR)/$(lib) $(CC_LD_DYNPATH)$(CURLDIR)/$(lib) -lcurl
+		CURL_LIBCURL=
+	else
+		CURL_CONFIG ?= curl-config
+		ifeq "$(CURL_CONFIG)" ""
+			CURL_LIBCURL =
+		else
+			CURL_LIBCURL := $(shell $(CURL_CONFIG) --libs)
+		endif
+	endif
+
+	ifeq "$(CURL_LIBCURL)" ""
+		ifdef CURL_STATIC
+                        $(error "CURL_STATIC must be used with CURL_CONFIG")
+		endif
+		ifdef CURLDIR
+			# Try "-Wl,-rpath=$(CURLDIR)/$(lib)" in such a case.
+			BASIC_CFLAGS += -I$(CURLDIR)/include
+			CURL_LIBCURL = -L$(CURLDIR)/$(lib) $(CC_LD_DYNPATH)$(CURLDIR)/$(lib) -lcurl
+		else
+			CURL_LIBCURL = -lcurl
+		endif
 		ifdef NEEDS_SSL_WITH_CURL
 			CURL_LIBCURL += -lssl
 			ifdef NEEDS_CRYPTO_WITH_SSL
@@ -1140,17 +1160,11 @@ else
 			CURL_LIBCURL += -lidn
 		endif
 	else
-		CURL_CONFIG ?= curl-config
 		BASIC_CFLAGS += $(shell $(CURL_CONFIG) --cflags)
 		ifdef CURL_STATIC
 			CURL_LIBCURL = $(shell $(CURL_CONFIG) --static-libs)
 			ifeq "$(CURL_LIBCURL)" ""
-				$(error libcurl not detected or not compiled with static support)
-			endif
-		else
-			CURL_LIBCURL = $(shell $(CURL_CONFIG) --libs)
-			ifeq "$(CURL_LIBCURL)" ""
-				$(error libcurl not detected; try setting CURLDIR)
+                                $(error libcurl not detected or not compiled with static support)
 			endif
 		endif
 	endif
-- 
1.9.1.423.g4596e3a