From: Weike Chen <alvin.chen@intel.com>
To: Linus Walleij <linus.walleij@linaro.org>,
Alexandre Courbot <gnurou@gmail.com>,
Grant Likely <grant.likely@linaro.org>,
Rob Herring <robh+dt@kernel.org>,
atull <atull@opensource.altera.com>
Cc: linux-gpio@vger.kernel.org, linux-kernel@vger.kernel.org,
devicetree@vger.kernel.org,
Boon Leong Ong <boon.leong.ong@intel.com>,
Hock Leong Kweh <hock.leong.kweh@intel.com>,
Darren Hart <dvhart@linux.intel.com>,
Sebastian Andrzej Siewior <sebastian@breakpoint.cc>,
Mika Westerberg <mika.westerberg@intel.com>,
Andy Shevchenko <andriy.shevchenko@linux.intel.com>,
Alvin Chen <alvin.chen@intel.com>
Subject: [PATCH 1/4 v5] GPIO: gpio-dwapb: Enable platform driver binding to MFD driver
Date: Wed, 17 Sep 2014 09:18:39 -0700 [thread overview]
Message-ID: <1410970722-8579-2-git-send-email-alvin.chen@intel.com> (raw)
In-Reply-To: <1410970722-8579-1-git-send-email-alvin.chen@intel.com>
The Synopsys DesignWare APB GPIO driver only supports open firmware devices.
But, like Intel Quark X1000 SOC, which has a single PCI function exporting
a GPIO and an I2C controller, it is a Multifunction device. This patch is
to enable the current Synopsys DesignWare APB GPIO driver to support the
Multifunction device which exports the designware GPIO controller.
Reviewed-by: Hock Leong Kweh <hock.leong.kweh@intel.com>
Signed-off-by: Weike Chen <alvin.chen@intel.com>
---
drivers/gpio/Kconfig | 1 -
drivers/gpio/gpio-dwapb.c | 224 ++++++++++++++++++++++--------
include/linux/platform_data/gpio-dwapb.h | 32 +++++
3 files changed, 199 insertions(+), 58 deletions(-)
create mode 100644 include/linux/platform_data/gpio-dwapb.h
diff --git a/drivers/gpio/Kconfig b/drivers/gpio/Kconfig
index 9de1515..8250a44 100644
--- a/drivers/gpio/Kconfig
+++ b/drivers/gpio/Kconfig
@@ -136,7 +136,6 @@ config GPIO_DWAPB
tristate "Synopsys DesignWare APB GPIO driver"
select GPIO_GENERIC
select GENERIC_IRQ_CHIP
- depends on OF_GPIO
help
Say Y or M here to build support for the Synopsys DesignWare APB
GPIO block.
diff --git a/drivers/gpio/gpio-dwapb.c b/drivers/gpio/gpio-dwapb.c
index d6618a6..27466b5 100644
--- a/drivers/gpio/gpio-dwapb.c
+++ b/drivers/gpio/gpio-dwapb.c
@@ -21,6 +21,8 @@
#include <linux/of_irq.h>
#include <linux/platform_device.h>
#include <linux/spinlock.h>
+#include <linux/platform_data/gpio-dwapb.h>
+#include <linux/slab.h>
#define GPIO_SWPORTA_DR 0x00
#define GPIO_SWPORTA_DDR 0x04
@@ -84,11 +86,10 @@ static void dwapb_toggle_trigger(struct dwapb_gpio *gpio, unsigned int offs)
writel(v, gpio->regs + GPIO_INT_POLARITY);
}
-static void dwapb_irq_handler(u32 irq, struct irq_desc *desc)
+static u32 dwapb_do_irq(struct dwapb_gpio *gpio)
{
- struct dwapb_gpio *gpio = irq_get_handler_data(irq);
- struct irq_chip *chip = irq_desc_get_chip(desc);
u32 irq_status = readl_relaxed(gpio->regs + GPIO_INTSTATUS);
+ u32 ret = irq_status;
while (irq_status) {
int hwirq = fls(irq_status) - 1;
@@ -102,6 +103,16 @@ static void dwapb_irq_handler(u32 irq, struct irq_desc *desc)
dwapb_toggle_trigger(gpio, hwirq);
}
+ return ret;
+}
+
+static void dwapb_irq_handler(u32 irq, struct irq_desc *desc)
+{
+ struct dwapb_gpio *gpio = irq_get_handler_data(irq);
+ struct irq_chip *chip = irq_desc_get_chip(desc);
+
+ dwapb_do_irq(gpio);
+
if (chip->irq_eoi)
chip->irq_eoi(irq_desc_get_irq_data(desc));
}
@@ -207,22 +218,26 @@ static int dwapb_irq_set_type(struct irq_data *d, u32 type)
return 0;
}
+static irqreturn_t dwapb_irq_handler_mfd(int irq, void *dev_id)
+{
+ u32 worked;
+ struct dwapb_gpio *gpio = dev_id;
+
+ worked = dwapb_do_irq(gpio);
+
+ return worked ? IRQ_HANDLED : IRQ_NONE;
+}
+
static void dwapb_configure_irqs(struct dwapb_gpio *gpio,
- struct dwapb_gpio_port *port)
+ struct dwapb_gpio_port *port,
+ struct dwapb_port_property *pp)
{
struct gpio_chip *gc = &port->bgc.gc;
- struct device_node *node = gc->of_node;
- struct irq_chip_generic *irq_gc;
+ struct device_node *node = pp->node;
+ struct irq_chip_generic *irq_gc = NULL;
unsigned int hwirq, ngpio = gc->ngpio;
struct irq_chip_type *ct;
- int err, irq, i;
-
- irq = irq_of_parse_and_map(node, 0);
- if (!irq) {
- dev_warn(gpio->dev, "no irq for bank %s\n",
- port->bgc.gc.of_node->full_name);
- return;
- }
+ int err, i;
gpio->domain = irq_domain_add_linear(node, ngpio,
&irq_generic_chip_ops, gpio);
@@ -269,8 +284,24 @@ static void dwapb_configure_irqs(struct dwapb_gpio *gpio,
irq_gc->chip_types[1].type = IRQ_TYPE_EDGE_BOTH;
irq_gc->chip_types[1].handler = handle_edge_irq;
- irq_set_chained_handler(irq, dwapb_irq_handler);
- irq_set_handler_data(irq, gpio);
+ if (!pp->irq_shared) {
+ irq_set_chained_handler(pp->irq, dwapb_irq_handler);
+ irq_set_handler_data(pp->irq, gpio);
+ } else {
+ /*
+ * Request a shared IRQ since where MFD would have devices
+ * using the same irq pin
+ */
+ err = devm_request_irq(gpio->dev, pp->irq,
+ dwapb_irq_handler_mfd,
+ IRQF_SHARED, "gpio-dwapb-mfd", gpio);
+ if (err) {
+ dev_err(gpio->dev, "error requesting IRQ\n");
+ irq_domain_remove(gpio->domain);
+ gpio->domain = NULL;
+ return;
+ }
+ }
for (hwirq = 0 ; hwirq < ngpio ; hwirq++)
irq_create_mapping(gpio->domain, hwirq);
@@ -296,57 +327,42 @@ static void dwapb_irq_teardown(struct dwapb_gpio *gpio)
}
static int dwapb_gpio_add_port(struct dwapb_gpio *gpio,
- struct device_node *port_np,
+ struct dwapb_port_property *pp,
unsigned int offs)
{
struct dwapb_gpio_port *port;
- u32 port_idx, ngpio;
void __iomem *dat, *set, *dirout;
int err;
- if (of_property_read_u32(port_np, "reg", &port_idx) ||
- port_idx >= DWAPB_MAX_PORTS) {
- dev_err(gpio->dev, "missing/invalid port index for %s\n",
- port_np->full_name);
- return -EINVAL;
- }
-
port = &gpio->ports[offs];
port->gpio = gpio;
- if (of_property_read_u32(port_np, "snps,nr-gpios", &ngpio)) {
- dev_info(gpio->dev, "failed to get number of gpios for %s\n",
- port_np->full_name);
- ngpio = 32;
- }
-
- dat = gpio->regs + GPIO_EXT_PORTA + (port_idx * GPIO_EXT_PORT_SIZE);
- set = gpio->regs + GPIO_SWPORTA_DR + (port_idx * GPIO_SWPORT_DR_SIZE);
+ dat = gpio->regs + GPIO_EXT_PORTA + (pp->idx * GPIO_EXT_PORT_SIZE);
+ set = gpio->regs + GPIO_SWPORTA_DR + (pp->idx * GPIO_SWPORT_DR_SIZE);
dirout = gpio->regs + GPIO_SWPORTA_DDR +
- (port_idx * GPIO_SWPORT_DDR_SIZE);
+ (pp->idx * GPIO_SWPORT_DDR_SIZE);
err = bgpio_init(&port->bgc, gpio->dev, 4, dat, set, NULL, dirout,
NULL, false);
if (err) {
dev_err(gpio->dev, "failed to init gpio chip for %s\n",
- port_np->full_name);
+ pp->name);
return err;
}
- port->bgc.gc.ngpio = ngpio;
- port->bgc.gc.of_node = port_np;
+#ifdef CONFIG_OF_GPIO
+ port->bgc.gc.of_node = pp->node;
+#endif
+ port->bgc.gc.ngpio = pp->ngpio;
+ port->bgc.gc.base = pp->gpio_base;
- /*
- * Only port A can provide interrupts in all configurations of the IP.
- */
- if (port_idx == 0 &&
- of_property_read_bool(port_np, "interrupt-controller"))
- dwapb_configure_irqs(gpio, port);
+ if (pp->irq)
+ dwapb_configure_irqs(gpio, port, pp);
err = gpiochip_add(&port->bgc.gc);
if (err)
dev_err(gpio->dev, "failed to register gpiochip for %s\n",
- port_np->full_name);
+ pp->name);
else
port->is_registered = true;
@@ -362,25 +378,116 @@ static void dwapb_gpio_unregister(struct dwapb_gpio *gpio)
gpiochip_remove(&gpio->ports[m].bgc.gc);
}
+static struct dwapb_platform_data *
+dwapb_gpio_get_pdata_of(struct device *dev)
+{
+ struct device_node *node, *port_np;
+ struct dwapb_platform_data *pdata;
+ struct dwapb_port_property *pp;
+ int nports;
+ int i;
+
+ node = dev->of_node;
+ if (!IS_ENABLED(CONFIG_OF_GPIO) || !node)
+ return ERR_PTR(-ENODEV);
+
+ nports = of_get_child_count(node);
+ if (nports == 0)
+ return ERR_PTR(-ENODEV);
+
+ pdata = kzalloc(sizeof(*pdata), GFP_KERNEL);
+ if (!pdata)
+ return ERR_PTR(-ENOMEM);
+
+ pdata->properties = kcalloc(nports, sizeof(*pp), GFP_KERNEL);
+ if (!pdata->properties) {
+ kfree(pdata);
+ return ERR_PTR(-ENOMEM);
+ }
+
+ pdata->nports = nports;
+
+ i = 0;
+ for_each_child_of_node(node, port_np) {
+ pp = &pdata->properties[i++];
+ pp->node = port_np;
+
+ if (of_property_read_u32(port_np, "reg", &pp->idx) ||
+ pp->idx >= DWAPB_MAX_PORTS) {
+ dev_err(dev, "missing/invalid port index for %s\n",
+ port_np->full_name);
+ kfree(pdata->properties);
+ kfree(pdata);
+ return ERR_PTR(-EINVAL);
+ }
+
+ if (of_property_read_u32(port_np, "snps,nr-gpios",
+ &pp->ngpio)) {
+ dev_info(dev, "failed to get number of gpios for %s\n",
+ port_np->full_name);
+ pp->ngpio = 32;
+ }
+
+ /*
+ * Only port A can provide interrupts in all configurations of
+ * the IP.
+ */
+ if (pp->idx == 0 &&
+ of_property_read_bool(port_np, "interrupt-controller")) {
+ pp->irq = irq_of_parse_and_map(port_np, 0);
+ if (!pp->irq) {
+ dev_warn(dev, "no irq for bank %s\n",
+ port_np->full_name);
+ }
+ }
+
+ pp->irq_shared = false;
+ pp->gpio_base = -1;
+ pp->name = port_np->full_name;
+ }
+
+ return pdata;
+}
+
+static inline void dwapb_free_pdata_of(struct dwapb_platform_data *pdata)
+{
+ if (!IS_ENABLED(CONFIG_OF_GPIO) || !pdata)
+ return;
+
+ kfree(pdata->properties);
+ kfree(pdata);
+}
+
static int dwapb_gpio_probe(struct platform_device *pdev)
{
+ unsigned int i;
struct resource *res;
struct dwapb_gpio *gpio;
- struct device_node *np;
int err;
- unsigned int offs = 0;
+ struct device *dev = &pdev->dev;
+ struct dwapb_platform_data *pdata = dev_get_platdata(dev);
+ bool is_pdata_alloc = !pdata;
+
+ if (is_pdata_alloc) {
+ pdata = dwapb_gpio_get_pdata_of(dev);
+ if (IS_ERR(pdata))
+ return PTR_ERR(pdata);
+ }
- gpio = devm_kzalloc(&pdev->dev, sizeof(*gpio), GFP_KERNEL);
- if (!gpio)
- return -ENOMEM;
- gpio->dev = &pdev->dev;
+ if (!pdata->nports) {
+ err = -ENODEV;
+ goto out_err;
+ }
- gpio->nr_ports = of_get_child_count(pdev->dev.of_node);
- if (!gpio->nr_ports) {
- err = -EINVAL;
+ gpio = devm_kzalloc(&pdev->dev, sizeof(*gpio), GFP_KERNEL);
+ if (!gpio) {
+ err = -ENOMEM;
goto out_err;
}
- gpio->ports = devm_kzalloc(&pdev->dev, gpio->nr_ports *
+ gpio->dev = &pdev->dev;
+ gpio->nr_ports = pdata->nports;
+
+ gpio->ports = devm_kcalloc(&pdev->dev, gpio->nr_ports,
sizeof(*gpio->ports), GFP_KERNEL);
if (!gpio->ports) {
err = -ENOMEM;
@@ -394,20 +501,23 @@ static int dwapb_gpio_probe(struct platform_device *pdev)
goto out_err;
}
- for_each_child_of_node(pdev->dev.of_node, np) {
- err = dwapb_gpio_add_port(gpio, np, offs++);
+ for (i = 0; i < gpio->nr_ports; i++) {
+ err = dwapb_gpio_add_port(gpio, &pdata->properties[i], i);
if (err)
goto out_unregister;
}
platform_set_drvdata(pdev, gpio);
- return 0;
+ goto out_err;
out_unregister:
dwapb_gpio_unregister(gpio);
dwapb_irq_teardown(gpio);
out_err:
+ if (is_pdata_alloc)
+ dwapb_free_pdata_of(pdata);
+
return err;
}
diff --git a/include/linux/platform_data/gpio-dwapb.h b/include/linux/platform_data/gpio-dwapb.h
new file mode 100644
index 0000000..28702c8
--- /dev/null
+++ b/include/linux/platform_data/gpio-dwapb.h
@@ -0,0 +1,32 @@
+/*
+ * Copyright(c) 2014 Intel Corporation.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms and conditions of the GNU General Public License,
+ * version 2, as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
+ * more details.
+ */
+
+#ifndef GPIO_DW_APB_H
+#define GPIO_DW_APB_H
+
+struct dwapb_port_property {
+ struct device_node *node;
+ const char *name;
+ unsigned int idx;
+ unsigned int ngpio;
+ unsigned int gpio_base;
+ unsigned int irq;
+ bool irq_shared;
+};
+
+struct dwapb_platform_data {
+ struct dwapb_port_property *properties;
+ unsigned int nports;
+};
+
+#endif
--
1.7.9.5
next prev parent reply other threads:[~2014-09-17 16:18 UTC|newest]
Thread overview: 10+ messages / expand[flat|nested] mbox.gz Atom feed top
2014-09-17 16:18 [PATCH 0/4 v5] The Designware GPIO Supporting Weike Chen
2014-09-17 16:18 ` Weike Chen [this message]
2014-09-23 12:09 ` [PATCH 1/4 v5] GPIO: gpio-dwapb: Enable platform driver binding to MFD driver Linus Walleij
2014-09-17 16:18 ` [PATCH 2/4 v5] GPIO: gpio-dwapb: Change readl&writel to dwapb_read&dwapb_write Weike Chen
2014-09-23 12:10 ` Linus Walleij
2014-09-17 16:18 ` [PATCH 3/4 v5] GPIO: gpio-dwapb: Support Debounce Weike Chen
2014-09-23 12:12 ` Linus Walleij
2014-09-17 16:18 ` [PATCH 4/4 v5] GPIO: gpio-dwapb: Suspend & Resume PM enabling Weike Chen
2014-09-17 8:50 ` Andy Shevchenko
2014-09-23 14:41 ` Linus Walleij
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1410970722-8579-2-git-send-email-alvin.chen@intel.com \
--to=alvin.chen@intel.com \
--cc=andriy.shevchenko@linux.intel.com \
--cc=atull@opensource.altera.com \
--cc=boon.leong.ong@intel.com \
--cc=devicetree@vger.kernel.org \
--cc=dvhart@linux.intel.com \
--cc=gnurou@gmail.com \
--cc=grant.likely@linaro.org \
--cc=hock.leong.kweh@intel.com \
--cc=linus.walleij@linaro.org \
--cc=linux-gpio@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=mika.westerberg@intel.com \
--cc=robh+dt@kernel.org \
--cc=sebastian@breakpoint.cc \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.