From: "Martin Hundebøll" <martin@hundeboll.net>
To: Johannes Berg <johannes@sipsolutions.net>
Cc: linux-wireless <linux-wireless@vger.kernel.org>
Subject: iwlwifi: ibss on 6205 always stuck at 1 Mbps
Date: Mon, 29 Sep 2014 15:27:48 +0200 [thread overview]
Message-ID: <1411997268.1663.0@smtp.hundeboll.net> (raw)
[-- Attachment #1: Type: text/plain, Size: 2773 bytes --]
Hi,
I get bad performance with IBSS on my 6205 devices running iwlwifi.
They seem to be stuck on 1 Mbps and through bisecting, it comes down to
this bad commit:
3ac40edadcb7799391452ffaa1745084c3e4c747
('iwlwifi: calculate active legacy rates per station')
https://github.com/torvalds/linux/commit/3ac40edadcb7799391452ffaa1745084c3e4c747
I have tested the issue on a few different settings:
iwlwifi (6205) => iwlwifi (6205): BAD
iwlwifi (6205) => ath9k_htc: BAD
iwlwifi (6205) => iwlwifi (6300): BAD
iwlwifi (6300) => iwlwifi (6205): GOOD
ath9k_htc => iwlwifi (6205): GOOD
So, as the first bad commit and the simple tests indicate, the issue is
related to the rate selection for 6205 devices.
dmesg and phy-info from an affected device is attached. Let me know if
more information is needed.
Thanks,
Martin
core@core01:~$ sudo iw wlan0 info
Interface wlan0
ifindex 3
wdev 0x1
addr a0:88:b4:bf:f4:cc
ssid core-test
type IBSS
wiphy 0
channel 6 (2437 MHz), width: 20 MHz (no HT), center1: 2437 MHz
core@core01:~$ sudo iw wlan0 station dump
Station 24:77:03:d7:6a:7c (on wlan0)
inactive time: 32 ms
rx bytes: 11009701
rx packets: 24719
tx bytes: 1264256
tx packets: 4032
tx retries: 501
tx failed: 0
signal: -44 dBm
signal avg: -43 dBm
tx bitrate: 1.0 MBit/s
rx bitrate: 54.0 MBit/s
authorized: yes
authenticated: yes
preamble: long
WMM/WME: yes
MFP: no
TDLS peer: no
Station f8:d1:11:0c:3f:2b (on wlan0)
inactive time: 4 ms
rx bytes: 13269604
rx packets: 33953
tx bytes: 1332906
tx packets: 4831
tx retries: 765
tx failed: 0
signal: -46 dBm
signal avg: -47 dBm
tx bitrate: 1.0 MBit/s
rx bitrate: 1.0 MBit/s
authorized: yes
authenticated: yes
preamble: long
WMM/WME: yes
MFP: no
TDLS peer: no
Station a0:88:b4:d8:b0:d8 (on wlan0)
inactive time: 20 ms
rx bytes: 7199547
rx packets: 86184
tx bytes: 135242
tx packets: 1573
tx retries: 323
tx failed: 0
signal: -41 dBm
signal avg: -40 dBm
tx bitrate: 54.0 MBit/s
rx bitrate: 1.0 MBit/s
authorized: yes
authenticated: yes
preamble: long
WMM/WME: yes
MFP: no
TDLS peer: no
Station 08:11:96:06:22:48 (on wlan0)
inactive time: 76 ms
rx bytes: 3290846
rx packets: 83190
tx bytes: 0
tx packets: 0
tx retries: 0
tx failed: 0
signal: -12 dBm
signal avg: -11 dBm
tx bitrate: 1.0 MBit/s
rx bitrate: 1.0 MBit/s
authorized: yes
authenticated: yes
preamble: long
WMM/WME: yes
MFP: no
TDLS peer: no
Station a0:88:b4:dc:f1:e0 (on wlan0)
inactive time: 104 ms
rx bytes: 3092949
rx packets: 78249
tx bytes: 0
tx packets: 0
tx retries: 0
tx failed: 0
signal: -24 dBm
signal avg: -23 dBm
tx bitrate: 1.0 MBit/s
rx bitrate: 1.0 MBit/s
authorized: yes
authenticated: yes
preamble: long
WMM/WME: yes
MFP: no
TDLS peer: no
[-- Attachment #2.1: phy.info --]
[-- Type: text/plain, Size: 5776 bytes --]
Wiphy phy0
max # scan SSIDs: 20
max scan IEs length: 195 bytes
Coverage class: 0 (up to 0m)
Device supports RSN-IBSS.
Supported Ciphers:
* WEP40 (00-0f-ac:1)
* WEP104 (00-0f-ac:5)
* TKIP (00-0f-ac:2)
* CCMP (00-0f-ac:4)
Available Antennas: TX 0 RX 0
Supported interface modes:
* IBSS
* managed
* AP
* AP/VLAN
* monitor
Band 1:
Capabilities: 0x1072
HT20/HT40
Static SM Power Save
RX Greenfield
RX HT20 SGI
RX HT40 SGI
No RX STBC
Max AMSDU length: 3839 bytes
DSSS/CCK HT40
Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
Minimum RX AMPDU time spacing: 4 usec (0x05)
HT TX/RX MCS rate indexes supported: 0-15, 32
Bitrates (non-HT):
* 1.0 Mbps
* 2.0 Mbps (short preamble supported)
* 5.5 Mbps (short preamble supported)
* 11.0 Mbps (short preamble supported)
* 6.0 Mbps
* 9.0 Mbps
* 12.0 Mbps
* 18.0 Mbps
* 24.0 Mbps
* 36.0 Mbps
* 48.0 Mbps
* 54.0 Mbps
Frequencies:
* 2412 MHz [1] (15.0 dBm)
* 2417 MHz [2] (15.0 dBm)
* 2422 MHz [3] (15.0 dBm)
* 2427 MHz [4] (15.0 dBm)
* 2432 MHz [5] (15.0 dBm)
* 2437 MHz [6] (15.0 dBm)
* 2442 MHz [7] (15.0 dBm)
* 2447 MHz [8] (15.0 dBm)
* 2452 MHz [9] (15.0 dBm)
* 2457 MHz [10] (15.0 dBm)
* 2462 MHz [11] (15.0 dBm)
* 2467 MHz [12] (15.0 dBm) (no IR)
* 2472 MHz [13] (15.0 dBm) (no IR)
Band 2:
Capabilities: 0x1072
HT20/HT40
Static SM Power Save
RX Greenfield
RX HT20 SGI
RX HT40 SGI
No RX STBC
Max AMSDU length: 3839 bytes
DSSS/CCK HT40
Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
Minimum RX AMPDU time spacing: 4 usec (0x05)
HT TX/RX MCS rate indexes supported: 0-15, 32
Bitrates (non-HT):
* 6.0 Mbps
* 9.0 Mbps
* 12.0 Mbps
* 18.0 Mbps
* 24.0 Mbps
* 36.0 Mbps
* 48.0 Mbps
* 54.0 Mbps
Frequencies:
* 5180 MHz [36] (15.0 dBm) (no IR)
* 5200 MHz [40] (15.0 dBm) (no IR)
* 5220 MHz [44] (15.0 dBm) (no IR)
* 5240 MHz [48] (15.0 dBm) (no IR)
* 5260 MHz [52] (15.0 dBm) (no IR, radar detection)
DFS state: usable (for 4080 sec)
* 5280 MHz [56] (15.0 dBm) (no IR, radar detection)
DFS state: usable (for 4080 sec)
* 5300 MHz [60] (15.0 dBm) (no IR, radar detection)
DFS state: usable (for 4080 sec)
* 5320 MHz [64] (15.0 dBm) (no IR, radar detection)
DFS state: usable (for 4080 sec)
* 5500 MHz [100] (15.0 dBm) (no IR, radar detection)
DFS state: usable (for 4080 sec)
* 5520 MHz [104] (15.0 dBm) (no IR, radar detection)
DFS state: usable (for 4080 sec)
* 5540 MHz [108] (15.0 dBm) (no IR, radar detection)
DFS state: usable (for 4080 sec)
* 5560 MHz [112] (15.0 dBm) (no IR, radar detection)
DFS state: usable (for 4080 sec)
* 5580 MHz [116] (15.0 dBm) (no IR, radar detection)
DFS state: usable (for 4080 sec)
* 5600 MHz [120] (15.0 dBm) (no IR, radar detection)
DFS state: usable (for 4080 sec)
* 5620 MHz [124] (15.0 dBm) (no IR, radar detection)
DFS state: usable (for 4080 sec)
* 5640 MHz [128] (15.0 dBm) (no IR, radar detection)
DFS state: usable (for 4080 sec)
* 5660 MHz [132] (15.0 dBm) (no IR, radar detection)
DFS state: usable (for 4080 sec)
* 5680 MHz [136] (15.0 dBm) (no IR, radar detection)
DFS state: usable (for 4080 sec)
* 5700 MHz [140] (15.0 dBm) (no IR, radar detection)
DFS state: usable (for 4080 sec)
* 5745 MHz [149] (15.0 dBm) (no IR)
* 5765 MHz [153] (15.0 dBm) (no IR)
* 5785 MHz [157] (15.0 dBm) (no IR)
* 5805 MHz [161] (15.0 dBm) (no IR)
* 5825 MHz [165] (15.0 dBm) (no IR)
Supported commands:
* new_interface
* set_interface
* new_key
* start_ap
* new_station
* new_mpath
* set_mesh_config
* set_bss
* authenticate
* associate
* deauthenticate
* disassociate
* join_ibss
* join_mesh
* set_tx_bitrate_mask
* frame
* frame_wait_cancel
* set_wiphy_netns
* set_channel
* set_wds_peer
* probe_client
* set_noack_map
* register_beacons
* start_p2p_device
* set_mcast_rate
* Unknown command (104)
* connect
* disconnect
Supported TX frame types:
* IBSS: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* managed: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* AP: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* AP/VLAN: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* mesh point: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* P2P-client: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* P2P-GO: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* P2P-device: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
Supported RX frame types:
* IBSS: 0x40 0xb0 0xc0 0xd0
* managed: 0x40 0xd0
* AP: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
* AP/VLAN: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
* mesh point: 0xb0 0xc0 0xd0
* P2P-client: 0x40 0xd0
* P2P-GO: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
* P2P-device: 0x40 0xd0
software interface modes (can always be added):
* AP/VLAN
* monitor
valid interface combinations:
* #{ managed } <= 1, #{ AP } <= 1,
total <= 2, #channels <= 1, STA/AP BI must match
* #{ managed } <= 2,
total <= 2, #channels <= 1
HT Capability overrides:
* MCS: ff ff ff ff ff ff ff ff ff ff
* maximum A-MSDU length
* supported channel width
* short GI for 40 MHz
* max A-MPDU length exponent
* min MPDU start spacing
Device supports TX status socket option.
Device supports HT-IBSS.
Device supports scan flush.
[-- Warning: decoded text below may be mangled, UTF-8 assumed --]
[-- Attachment #2.2: dmesg.log --]
[-- Type: text/x-log, Size: 56384 bytes --]
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Initializing cgroup subsys cpuacct
[ 0.000000] Linux version 3.14-2-amd64 (debian-kernel@lists.debian.org) (gcc version 4.8.3 (Debian 4.8.3-7) ) #1 SMP Debian 3.14.15-2 (2014-08-09)
[ 0.000000] Command line: BOOT_IMAGE=/boot/vmlinuz-3.14-2-amd64 root=UUID=96100e50-8deb-404a-988b-681856ef65f9 ro quiet
[ 0.000000] Disabled fast string operations
[ 0.000000] e820: BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000009d7ff] usable
[ 0.000000] BIOS-e820: [mem 0x000000000009d800-0x000000000009ffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000000e0000-0x00000000000fffff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000000100000-0x00000000da99efff] usable
[ 0.000000] BIOS-e820: [mem 0x00000000da99f000-0x00000000dae9efff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000dae9f000-0x00000000daf9efff] ACPI NVS
[ 0.000000] BIOS-e820: [mem 0x00000000daf9f000-0x00000000daffefff] ACPI data
[ 0.000000] BIOS-e820: [mem 0x00000000dafff000-0x00000000daffffff] usable
[ 0.000000] BIOS-e820: [mem 0x00000000db000000-0x00000000df9fffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000f8000000-0x00000000fbffffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fec00000-0x00000000fec00fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fed08000-0x00000000fed08fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fed10000-0x00000000fed19fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fed1c000-0x00000000fed1ffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fee00000-0x00000000fee00fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000ffd20000-0x00000000ffffffff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000100000000-0x000000021e5fffff] usable
[ 0.000000] NX (Execute Disable) protection: active
[ 0.000000] SMBIOS 2.6 present.
[ 0.000000] DMI: LENOVO 4290A11/4290A11, BIOS 8DET50WW (1.20 ) 07/07/2011
[ 0.000000] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved
[ 0.000000] e820: remove [mem 0x000a0000-0x000fffff] usable
[ 0.000000] No AGP bridge found
[ 0.000000] e820: last_pfn = 0x21e600 max_arch_pfn = 0x400000000
[ 0.000000] MTRR default type: uncachable
[ 0.000000] MTRR fixed ranges enabled:
[ 0.000000] 00000-9FFFF write-back
[ 0.000000] A0000-BFFFF uncachable
[ 0.000000] C0000-FFFFF write-protect
[ 0.000000] MTRR variable ranges enabled:
[ 0.000000] 0 base 000000000 mask F80000000 write-back
[ 0.000000] 1 base 080000000 mask FC0000000 write-back
[ 0.000000] 2 base 0C0000000 mask FE0000000 write-back
[ 0.000000] 3 base 0DC000000 mask FFC000000 uncachable
[ 0.000000] 4 base 0DB000000 mask FFF000000 uncachable
[ 0.000000] 5 base 100000000 mask F00000000 write-back
[ 0.000000] 6 base 200000000 mask FE0000000 write-back
[ 0.000000] 7 base 21F000000 mask FFF000000 uncachable
[ 0.000000] 8 base 21E800000 mask FFF800000 uncachable
[ 0.000000] 9 base 21E600000 mask FFFE00000 uncachable
[ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[ 0.000000] e820: update [mem 0xdb000000-0xffffffff] usable ==> reserved
[ 0.000000] e820: last_pfn = 0xdb000 max_arch_pfn = 0x400000000
[ 0.000000] Base memory trampoline at [ffff880000097000] 97000 size 24576
[ 0.000000] reserving inaccessible SNB gfx pages
[ 0.000000] init_memory_mapping: [mem 0x00000000-0x000fffff]
[ 0.000000] [mem 0x00000000-0x000fffff] page 4k
[ 0.000000] BRK [0x01aaf000, 0x01aaffff] PGTABLE
[ 0.000000] BRK [0x01ab0000, 0x01ab0fff] PGTABLE
[ 0.000000] BRK [0x01ab1000, 0x01ab1fff] PGTABLE
[ 0.000000] init_memory_mapping: [mem 0x21e400000-0x21e5fffff]
[ 0.000000] [mem 0x21e400000-0x21e5fffff] page 2M
[ 0.000000] BRK [0x01ab2000, 0x01ab2fff] PGTABLE
[ 0.000000] init_memory_mapping: [mem 0x21c000000-0x21e3fffff]
[ 0.000000] [mem 0x21c000000-0x21e3fffff] page 2M
[ 0.000000] init_memory_mapping: [mem 0x200000000-0x21bffffff]
[ 0.000000] [mem 0x200000000-0x21bffffff] page 2M
[ 0.000000] init_memory_mapping: [mem 0x00100000-0xda99efff]
[ 0.000000] [mem 0x00100000-0x001fffff] page 4k
[ 0.000000] [mem 0x00200000-0xda7fffff] page 2M
[ 0.000000] [mem 0xda800000-0xda99efff] page 4k
[ 0.000000] init_memory_mapping: [mem 0xdafff000-0xdaffffff]
[ 0.000000] [mem 0xdafff000-0xdaffffff] page 4k
[ 0.000000] BRK [0x01ab3000, 0x01ab3fff] PGTABLE
[ 0.000000] init_memory_mapping: [mem 0x100000000-0x1ffffffff]
[ 0.000000] [mem 0x100000000-0x1ffffffff] page 2M
[ 0.000000] BRK [0x01ab4000, 0x01ab4fff] PGTABLE
[ 0.000000] RAMDISK: [mem 0x3657e000-0x372b6fff]
[ 0.000000] ACPI: RSDP 00000000000f00e0 000024 (v02 LENOVO)
[ 0.000000] ACPI: XSDT 00000000daffe120 0000A4 (v01 LENOVO TP-8D 00001200 PTEC 00000002)
[ 0.000000] ACPI: FACP 00000000dafe7000 0000F4 (v04 LENOVO TP-8D 00001200 PTL 00000002)
[ 0.000000] ACPI: DSDT 00000000dafea000 00F322 (v01 LENOVO TP-8D 00001200 INTL 20061109)
[ 0.000000] ACPI: FACS 00000000daf2d000 000040
[ 0.000000] ACPI: SLIC 00000000daffd000 000176 (v01 LENOVO TP-8D 00001200 PTEC 00000001)
[ 0.000000] ACPI: SSDT 00000000daffc000 000249 (v01 LENOVO TP-SSDT2 00000200 INTL 20061109)
[ 0.000000] ACPI: SSDT 00000000daffb000 000033 (v01 LENOVO TP-SSDT1 00000100 INTL 20061109)
[ 0.000000] ACPI: SSDT 00000000daffa000 0007A7 (v01 LENOVO SataAhci 00001000 INTL 20061109)
[ 0.000000] ACPI: HPET 00000000dafe6000 000038 (v01 LENOVO TP-8D 00001200 PTL 00000002)
[ 0.000000] ACPI: APIC 00000000dafe5000 000098 (v01 LENOVO TP-8D 00001200 PTL 00000002)
[ 0.000000] ACPI: MCFG 00000000dafe4000 00003C (v01 LENOVO TP-8D 00001200 PTL 00000002)
[ 0.000000] ACPI: ECDT 00000000dafe3000 000052 (v01 LENOVO TP-8D 00001200 PTL 00000002)
[ 0.000000] ACPI: ASF! 00000000dafe9000 0000A5 (v32 LENOVO TP-8D 00001200 PTL 00000002)
[ 0.000000] ACPI: TCPA 00000000dafe2000 000032 (v02 PTL LENOVO 06040000 LNVO 00000001)
[ 0.000000] ACPI: SSDT 00000000dafe1000 000A27 (v01 PmRef Cpu0Ist 00003000 INTL 20061109)
[ 0.000000] ACPI: SSDT 00000000dafe0000 000996 (v01 PmRef CpuPm 00003000 INTL 20061109)
[ 0.000000] ACPI: UEFI 00000000dafdf000 00003E (v01 LENOVO TP-8D 00001200 PTL 00000002)
[ 0.000000] ACPI: UEFI 00000000dafde000 000042 (v01 PTL COMBUF 00000001 PTL 00000001)
[ 0.000000] ACPI: UEFI 00000000dafdd000 00027E (v01 LENOVO TP-8D 00001200 PTL 00000002)
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] No NUMA configuration found
[ 0.000000] Faking a node at [mem 0x0000000000000000-0x000000021e5fffff]
[ 0.000000] Initmem setup node 0 [mem 0x00000000-0x21e5fffff]
[ 0.000000] NODE_DATA [mem 0x21e5f4000-0x21e5f8fff]
[ 0.000000] [ffffea0000000000-ffffea00077fffff] PMD -> [ffff880215c00000-ffff88021cdfffff] on node 0
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x00001000-0x00ffffff]
[ 0.000000] DMA32 [mem 0x01000000-0xffffffff]
[ 0.000000] Normal [mem 0x100000000-0x21e5fffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00001000-0x0009cfff]
[ 0.000000] node 0: [mem 0x00100000-0xda99efff]
[ 0.000000] node 0: [mem 0xdafff000-0xdaffffff]
[ 0.000000] node 0: [mem 0x100000000-0x21e5fffff]
[ 0.000000] On node 0 totalpages: 2068284
[ 0.000000] DMA zone: 56 pages used for memmap
[ 0.000000] DMA zone: 156 pages reserved
[ 0.000000] DMA zone: 3996 pages, LIFO batch:0
[ 0.000000] DMA32 zone: 12186 pages used for memmap
[ 0.000000] DMA32 zone: 891296 pages, LIFO batch:31
[ 0.000000] Normal zone: 16037 pages used for memmap
[ 0.000000] Normal zone: 1172992 pages, LIFO batch:31
[ 0.000000] ACPI: PM-Timer IO Port: 0x408
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x02] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x03] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x05] lapic_id[0x00] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x06] lapic_id[0x00] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x07] lapic_id[0x00] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x08] lapic_id[0x00] disabled)
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] ACPI: HPET id: 0x8086a301 base: 0xfed00000
[ 0.000000] smpboot: Allowing 8 CPUs, 4 hotplug CPUs
[ 0.000000] nr_irqs_gsi: 40
[ 0.000000] PM: Registered nosave memory: [mem 0x0009d000-0x0009dfff]
[ 0.000000] PM: Registered nosave memory: [mem 0x0009e000-0x0009ffff]
[ 0.000000] PM: Registered nosave memory: [mem 0x000a0000-0x000dffff]
[ 0.000000] PM: Registered nosave memory: [mem 0x000e0000-0x000fffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xda99f000-0xdae9efff]
[ 0.000000] PM: Registered nosave memory: [mem 0xdae9f000-0xdaf9efff]
[ 0.000000] PM: Registered nosave memory: [mem 0xdaf9f000-0xdaffefff]
[ 0.000000] PM: Registered nosave memory: [mem 0xdb000000-0xdf9fffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xdfa00000-0xf7ffffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xf8000000-0xfbffffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfc000000-0xfebfffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfec00000-0xfec00fff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfec01000-0xfed07fff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfed08000-0xfed08fff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfed09000-0xfed0ffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfed10000-0xfed19fff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfed1a000-0xfed1bfff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfed1c000-0xfed1ffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfed20000-0xfedfffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfee00000-0xfee00fff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfee01000-0xffd1ffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xffd20000-0xffffffff]
[ 0.000000] e820: [mem 0xdfa00000-0xf7ffffff] available for PCI devices
[ 0.000000] Booting paravirtualized kernel on bare hardware
[ 0.000000] setup_percpu: NR_CPUS:512 nr_cpumask_bits:512 nr_cpu_ids:8 nr_node_ids:1
[ 0.000000] PERCPU: Embedded 29 pages/cpu @ffff88021e200000 s86080 r8192 d24512 u262144
[ 0.000000] pcpu-alloc: s86080 r8192 d24512 u262144 alloc=1*2097152
[ 0.000000] pcpu-alloc: [0] 0 1 2 3 4 5 6 7
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 2039849
[ 0.000000] Policy zone: Normal
[ 0.000000] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-3.14-2-amd64 root=UUID=96100e50-8deb-404a-988b-681856ef65f9 ro quiet
[ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.000000] xsave: enabled xstate_bv 0x7, cntxt size 0x340
[ 0.000000] Checking aperture...
[ 0.000000] No AGP bridge found
[ 0.000000] Calgary: detecting Calgary via BIOS EBDA area
[ 0.000000] Calgary: Unable to locate Rio Grande table in EBDA - bailing!
[ 0.000000] Memory: 8063968K/8273136K available (4957K kernel code, 747K rwdata, 1724K rodata, 1008K init, 960K bss, 209168K reserved)
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] RCU dyntick-idle grace-period acceleration is enabled.
[ 0.000000] RCU restricting CPUs from NR_CPUS=512 to nr_cpu_ids=8.
[ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=8
[ 0.000000] NR_IRQS:33024 nr_irqs:744 16
[ 0.000000] Console: colour VGA+ 80x25
[ 0.000000] console [tty0] enabled
[ 0.000000] hpet clockevent registered
[ 0.000000] tsc: Fast TSC calibration using PIT
[ 0.000000] tsc: Detected 2492.119 MHz processor
[ 0.000030] Calibrating delay loop (skipped), value calculated using timer frequency.. 4984.23 BogoMIPS (lpj=9968476)
[ 0.000032] pid_max: default: 32768 minimum: 301
[ 0.000039] ACPI: Core revision 20131218
[ 0.005789] ACPI: All ACPI Tables successfully acquired
[ 0.006668] Security Framework initialized
[ 0.006675] AppArmor: AppArmor disabled by boot time parameter
[ 0.006676] Yama: disabled by default; enable with sysctl kernel.yama.*
[ 0.007124] Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes)
[ 0.008710] Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes)
[ 0.009403] Mount-cache hash table entries: 16384 (order: 5, 131072 bytes)
[ 0.009413] Mountpoint-cache hash table entries: 16384 (order: 5, 131072 bytes)
[ 0.009588] Initializing cgroup subsys memory
[ 0.009592] Initializing cgroup subsys devices
[ 0.009594] Initializing cgroup subsys freezer
[ 0.009595] Initializing cgroup subsys net_cls
[ 0.009596] Initializing cgroup subsys blkio
[ 0.009597] Initializing cgroup subsys perf_event
[ 0.009618] Disabled fast string operations
[ 0.009619] CPU: Physical Processor ID: 0
[ 0.009620] CPU: Processor Core ID: 0
[ 0.009624] ENERGY_PERF_BIAS: Set to 'normal', was 'performance'
[ 0.009624] ENERGY_PERF_BIAS: View and update with x86_energy_perf_policy(8)
[ 0.009627] mce: CPU supports 7 MCE banks
[ 0.009638] CPU0: Thermal monitoring enabled (TM1)
[ 0.009646] Last level iTLB entries: 4KB 512, 2MB 8, 4MB 8
[ 0.009646] Last level dTLB entries: 4KB 512, 2MB 32, 4MB 32, 1GB 0
[ 0.009646] tlb_flushall_shift: 6
[ 0.009720] Freeing SMP alternatives memory: 20K (ffffffff819b8000 - ffffffff819bd000)
[ 0.011216] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.050909] smpboot: CPU0: Intel(R) Core(TM) i5-2520M CPU @ 2.50GHz (fam: 06, model: 2a, stepping: 07)
[ 0.050917] TSC deadline timer enabled
[ 0.050924] Performance Events: PEBS fmt1+, 16-deep LBR, SandyBridge events, full-width counters, Intel PMU driver.
[ 0.050929] perf_event_intel: PEBS disabled due to CPU errata, please upgrade microcode
[ 0.050931] ... version: 3
[ 0.050932] ... bit width: 48
[ 0.050933] ... generic registers: 4
[ 0.050934] ... value mask: 0000ffffffffffff
[ 0.050934] ... max period: 0000ffffffffffff
[ 0.050935] ... fixed-purpose events: 3
[ 0.050936] ... event mask: 000000070000000f
[ 0.051434] x86: Booting SMP configuration:
[ 0.051436] .... node #0, CPUs: #1
[ 0.062375] Disabled fast string operations
[ 0.064579] NMI watchdog: enabled on all CPUs, permanently consumes one hw-PMU counter.
[ 0.064672] #2
[ 0.075709] Disabled fast string operations
[ 0.077911] #3<6>[ 0.088947] Disabled fast string operations
[ 0.091068] x86: Booted up 1 node, 4 CPUs
[ 0.091072] smpboot: Total of 4 processors activated (19936.95 BogoMIPS)
[ 0.094075] devtmpfs: initialized
[ 0.098182] PM: Registering ACPI NVS region [mem 0xdae9f000-0xdaf9efff] (1048576 bytes)
[ 0.098326] pinctrl core: initialized pinctrl subsystem
[ 0.098377] NET: Registered protocol family 16
[ 0.098463] cpuidle: using governor ladder
[ 0.098464] cpuidle: using governor menu
[ 0.098490] ACPI FADT declares the system doesn't support PCIe ASPM, so disable it
[ 0.098491] ACPI: bus type PCI registered
[ 0.098493] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
[ 0.098738] PCI: MMCONFIG for domain 0000 [bus 00-3f] at [mem 0xf8000000-0xfbffffff] (base 0xf8000000)
[ 0.098741] PCI: MMCONFIG at [mem 0xf8000000-0xfbffffff] reserved in E820
[ 0.098818] PCI: Using configuration type 1 for base access
[ 0.099650] bio: create slab <bio-0> at 0
[ 0.099755] ACPI: Added _OSI(Module Device)
[ 0.099757] ACPI: Added _OSI(Processor Device)
[ 0.099758] ACPI: Added _OSI(3.0 _SCP Extensions)
[ 0.099759] ACPI: Added _OSI(Processor Aggregator Device)
[ 0.101040] ACPI : EC: EC description table is found, configuring boot EC
[ 0.104978] [Firmware Bug]: ACPI: BIOS _OSI(Linux) query ignored
[ 0.139630] ACPI: SSDT 00000000dae8c018 0008C0 (v01 PmRef Cpu0Cst 00003001 INTL 20061109)
[ 0.139953] ACPI: Dynamic OEM Table Load:
[ 0.139955] ACPI: SSDT (null) 0008C0 (v01 PmRef Cpu0Cst 00003001 INTL 20061109)
[ 0.151395] ACPI: SSDT 00000000dae8da98 000303 (v01 PmRef ApIst 00003000 INTL 20061109)
[ 0.151742] ACPI: Dynamic OEM Table Load:
[ 0.151744] ACPI: SSDT (null) 000303 (v01 PmRef ApIst 00003000 INTL 20061109)
[ 0.163282] ACPI: SSDT 00000000dae8bd98 000119 (v01 PmRef ApCst 00003000 INTL 20061109)
[ 0.163595] ACPI: Dynamic OEM Table Load:
[ 0.163596] ACPI: SSDT (null) 000119 (v01 PmRef ApCst 00003000 INTL 20061109)
[ 0.175744] ACPI: Interpreter enabled
[ 0.175749] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S1_] (20131218/hwxface-580)
[ 0.175753] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S2_] (20131218/hwxface-580)
[ 0.175764] ACPI: (supports S0 S3 S4 S5)
[ 0.175765] ACPI: Using IOAPIC for interrupt routing
[ 0.175787] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[ 0.176635] ACPI: ACPI Dock Station Driver: 3 docks/bays found
[ 0.191698] ACPI: Power Resource [PUBS] (on)
[ 0.196182] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11)
[ 0.196255] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 *7 9 10 11)
[ 0.196326] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 10 *11)
[ 0.196395] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 10 *11)
[ 0.196464] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 *10 11)
[ 0.196518] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 11) *0, disabled.
[ 0.196588] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 *7 9 10 11)
[ 0.196658] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 9 *10 11)
[ 0.196685] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-fe])
[ 0.196690] acpi PNP0A08:00: _OSC: OS supports [ExtendedConfig ASPM ClockPM Segments MSI]
[ 0.196845] acpi PNP0A08:00: _OSC: platform does not support [PCIeCapability]
[ 0.196917] acpi PNP0A08:00: _OSC: not requesting control; platform does not support [PCIeCapability]
[ 0.196919] acpi PNP0A08:00: _OSC: OS requested [PCIeHotplug PME AER PCIeCapability]
[ 0.196920] acpi PNP0A08:00: _OSC: platform willing to grant [PCIeHotplug PME AER]
[ 0.196922] acpi PNP0A08:00: _OSC failed (AE_SUPPORT); disabling ASPM
[ 0.196947] acpi PNP0A08:00: [Firmware Info]: MMCONFIG for domain 0000 [bus 00-3f] only partially covers this bridge
[ 0.197089] PCI host bridge to bus 0000:00
[ 0.197091] pci_bus 0000:00: root bus resource [bus 00-fe]
[ 0.197093] pci_bus 0000:00: root bus resource [io 0x0000-0x0cf7]
[ 0.197094] pci_bus 0000:00: root bus resource [io 0x0d00-0xffff]
[ 0.197096] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff]
[ 0.197097] pci_bus 0000:00: root bus resource [mem 0xdfa00000-0xfebfffff]
[ 0.197098] pci_bus 0000:00: root bus resource [mem 0xfed40000-0xfed4bfff]
[ 0.197105] pci 0000:00:00.0: [8086:0104] type 00 class 0x060000
[ 0.197182] pci 0000:00:02.0: [8086:0126] type 00 class 0x030000
[ 0.197192] pci 0000:00:02.0: reg 0x10: [mem 0xf0000000-0xf03fffff 64bit]
[ 0.197197] pci 0000:00:02.0: reg 0x18: [mem 0xe0000000-0xefffffff 64bit pref]
[ 0.197201] pci 0000:00:02.0: reg 0x20: [io 0x5000-0x503f]
[ 0.197292] pci 0000:00:16.0: [8086:1c3a] type 00 class 0x078000
[ 0.197313] pci 0000:00:16.0: reg 0x10: [mem 0xf2525000-0xf252500f 64bit]
[ 0.197377] pci 0000:00:16.0: PME# supported from D0 D3hot D3cold
[ 0.197444] pci 0000:00:16.3: [8086:1c3d] type 00 class 0x070002
[ 0.197461] pci 0000:00:16.3: reg 0x10: [io 0x50b0-0x50b7]
[ 0.197469] pci 0000:00:16.3: reg 0x14: [mem 0xf252c000-0xf252cfff]
[ 0.197595] pci 0000:00:19.0: [8086:1502] type 00 class 0x020000
[ 0.197613] pci 0000:00:19.0: reg 0x10: [mem 0xf2500000-0xf251ffff]
[ 0.197621] pci 0000:00:19.0: reg 0x14: [mem 0xf252b000-0xf252bfff]
[ 0.197629] pci 0000:00:19.0: reg 0x18: [io 0x5080-0x509f]
[ 0.197691] pci 0000:00:19.0: PME# supported from D0 D3hot D3cold
[ 0.197722] pci 0000:00:19.0: System wakeup disabled by ACPI
[ 0.197766] pci 0000:00:1a.0: [8086:1c2d] type 00 class 0x0c0320
[ 0.197787] pci 0000:00:1a.0: reg 0x10: [mem 0xf252a000-0xf252a3ff]
[ 0.197875] pci 0000:00:1a.0: PME# supported from D0 D3hot D3cold
[ 0.197907] pci 0000:00:1a.0: System wakeup disabled by ACPI
[ 0.197952] pci 0000:00:1b.0: [8086:1c20] type 00 class 0x040300
[ 0.197967] pci 0000:00:1b.0: reg 0x10: [mem 0xf2520000-0xf2523fff 64bit]
[ 0.198042] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
[ 0.198078] pci 0000:00:1b.0: System wakeup disabled by ACPI
[ 0.198124] pci 0000:00:1c.0: [8086:1c10] type 01 class 0x060400
[ 0.198248] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
[ 0.198330] pci 0000:00:1c.1: [8086:1c12] type 01 class 0x060400
[ 0.198465] pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold
[ 0.198548] pci 0000:00:1c.3: [8086:1c16] type 01 class 0x060400
[ 0.198683] pci 0000:00:1c.3: PME# supported from D0 D3hot D3cold
[ 0.198726] pci 0000:00:1c.3: System wakeup disabled by ACPI
[ 0.198769] pci 0000:00:1c.4: [8086:1c18] type 01 class 0x060400
[ 0.198903] pci 0000:00:1c.4: PME# supported from D0 D3hot D3cold
[ 0.198990] pci 0000:00:1d.0: [8086:1c26] type 00 class 0x0c0320
[ 0.199010] pci 0000:00:1d.0: reg 0x10: [mem 0xf2529000-0xf25293ff]
[ 0.199099] pci 0000:00:1d.0: PME# supported from D0 D3hot D3cold
[ 0.199129] pci 0000:00:1d.0: System wakeup disabled by ACPI
[ 0.199171] pci 0000:00:1f.0: [8086:1c4f] type 00 class 0x060100
[ 0.199337] pci 0000:00:1f.2: [8086:1c03] type 00 class 0x010601
[ 0.199354] pci 0000:00:1f.2: reg 0x10: [io 0x50a8-0x50af]
[ 0.199362] pci 0000:00:1f.2: reg 0x14: [io 0x50bc-0x50bf]
[ 0.199370] pci 0000:00:1f.2: reg 0x18: [io 0x50a0-0x50a7]
[ 0.199378] pci 0000:00:1f.2: reg 0x1c: [io 0x50b8-0x50bb]
[ 0.199385] pci 0000:00:1f.2: reg 0x20: [io 0x5060-0x507f]
[ 0.199393] pci 0000:00:1f.2: reg 0x24: [mem 0xf2528000-0xf25287ff]
[ 0.199437] pci 0000:00:1f.2: PME# supported from D3hot
[ 0.199501] pci 0000:00:1f.3: [8086:1c22] type 00 class 0x0c0500
[ 0.199517] pci 0000:00:1f.3: reg 0x10: [mem 0xf2524000-0xf25240ff 64bit]
[ 0.199537] pci 0000:00:1f.3: reg 0x20: [io 0xefa0-0xefbf]
[ 0.199686] pci 0000:00:1c.0: PCI bridge to [bus 02]
[ 0.199942] pci 0000:03:00.0: [8086:0085] type 00 class 0x028000
[ 0.200105] pci 0000:03:00.0: reg 0x10: [mem 0xf2400000-0xf2401fff 64bit]
[ 0.200821] pci 0000:03:00.0: PME# supported from D0 D3hot D3cold
[ 0.207329] pci 0000:00:1c.1: PCI bridge to [bus 03]
[ 0.207338] pci 0000:00:1c.1: bridge window [mem 0xf2400000-0xf24fffff]
[ 0.207451] acpiphp: Slot [1] registered
[ 0.207458] pci 0000:00:1c.3: PCI bridge to [bus 05-0c]
[ 0.207463] pci 0000:00:1c.3: bridge window [io 0x4000-0x4fff]
[ 0.207468] pci 0000:00:1c.3: bridge window [mem 0xf1c00000-0xf23fffff]
[ 0.207476] pci 0000:00:1c.3: bridge window [mem 0xf0400000-0xf0bfffff 64bit pref]
[ 0.207787] pci 0000:0d:00.0: [1180:e822] type 00 class 0x088001
[ 0.207806] pci 0000:0d:00.0: MMC controller base frequency changed to 50Mhz.
[ 0.207831] pci 0000:0d:00.0: reg 0x10: [mem 0xf1400000-0xf14000ff]
[ 0.208044] pci 0000:0d:00.0: supports D1 D2
[ 0.208045] pci 0000:0d:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.215286] pci 0000:00:1c.4: PCI bridge to [bus 0d]
[ 0.215296] pci 0000:00:1c.4: bridge window [io 0x3000-0x3fff]
[ 0.215305] pci 0000:00:1c.4: bridge window [mem 0xf1400000-0xf1bfffff]
[ 0.215318] pci 0000:00:1c.4: bridge window [mem 0xf0c00000-0xf13fffff 64bit pref]
[ 0.216156] ACPI: Enabled 4 GPEs in block 00 to 3F
[ 0.216222] ACPI : EC: GPE = 0x11, I/O: command/status = 0x66, data = 0x62
[ 0.216301] vgaarb: device added: PCI:0000:00:02.0,decodes=io+mem,owns=io+mem,locks=none
[ 0.216304] vgaarb: loaded
[ 0.216305] vgaarb: bridge control possible 0000:00:02.0
[ 0.216341] PCI: Using ACPI for IRQ routing
[ 0.218035] PCI: pci_cache_line_size set to 64 bytes
[ 0.218532] e820: reserve RAM buffer [mem 0x0009d800-0x0009ffff]
[ 0.218533] e820: reserve RAM buffer [mem 0xda99f000-0xdbffffff]
[ 0.218535] e820: reserve RAM buffer [mem 0xdb000000-0xdbffffff]
[ 0.218536] e820: reserve RAM buffer [mem 0x21e600000-0x21fffffff]
[ 0.218641] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0, 0, 0, 0, 0
[ 0.218646] hpet0: 8 comparators, 64-bit 14.318180 MHz counter
[ 0.220669] Switched to clocksource hpet
[ 0.222295] pnp: PnP ACPI init
[ 0.222310] ACPI: bus type PNP registered
[ 0.222661] system 00:00: [mem 0x00000000-0x0009ffff] could not be reserved
[ 0.222663] system 00:00: [mem 0x000c0000-0x000c3fff] could not be reserved
[ 0.222665] system 00:00: [mem 0x000c4000-0x000c7fff] could not be reserved
[ 0.222666] system 00:00: [mem 0x000c8000-0x000cbfff] has been reserved
[ 0.222668] system 00:00: [mem 0x000cc000-0x000cffff] has been reserved
[ 0.222669] system 00:00: [mem 0x000d0000-0x000d3fff] has been reserved
[ 0.222671] system 00:00: [mem 0x000d4000-0x000d7fff] has been reserved
[ 0.222672] system 00:00: [mem 0x000d8000-0x000dbfff] has been reserved
[ 0.222674] system 00:00: [mem 0x000dc000-0x000dffff] has been reserved
[ 0.222676] system 00:00: [mem 0x000e0000-0x000e3fff] could not be reserved
[ 0.222677] system 00:00: [mem 0x000e4000-0x000e7fff] could not be reserved
[ 0.222679] system 00:00: [mem 0x000e8000-0x000ebfff] could not be reserved
[ 0.222680] system 00:00: [mem 0x000ec000-0x000effff] could not be reserved
[ 0.222681] system 00:00: [mem 0x000f0000-0x000fffff] could not be reserved
[ 0.222683] system 00:00: [mem 0x00100000-0xdf9fffff] could not be reserved
[ 0.222685] system 00:00: [mem 0xfec00000-0xfed3ffff] could not be reserved
[ 0.222686] system 00:00: [mem 0xfed4c000-0xffffffff] could not be reserved
[ 0.222689] system 00:00: Plug and Play ACPI device, IDs PNP0c01 (active)
[ 0.222784] system 00:01: [io 0x0400-0x047f] could not be reserved
[ 0.222785] system 00:01: [io 0x0500-0x057f] has been reserved
[ 0.222787] system 00:01: [io 0x0800-0x080f] has been reserved
[ 0.222788] system 00:01: [io 0x15e0-0x15ef] has been reserved
[ 0.222790] system 00:01: [io 0x1600-0x167f] has been reserved
[ 0.222792] system 00:01: [mem 0xf8000000-0xfbffffff] has been reserved
[ 0.222794] system 00:01: [mem 0x00000000-0x00000fff] could not be reserved
[ 0.222795] system 00:01: [mem 0xfed1c000-0xfed1ffff] has been reserved
[ 0.222797] system 00:01: [mem 0xfed10000-0xfed13fff] has been reserved
[ 0.222798] system 00:01: [mem 0xfed18000-0xfed18fff] has been reserved
[ 0.222800] system 00:01: [mem 0xfed19000-0xfed19fff] has been reserved
[ 0.222802] system 00:01: [mem 0xfed45000-0xfed4bfff] has been reserved
[ 0.222803] system 00:01: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.222856] pnp 00:02: Plug and Play ACPI device, IDs PNP0103 (active)
[ 0.222865] pnp 00:03: [dma 4]
[ 0.222883] pnp 00:03: Plug and Play ACPI device, IDs PNP0200 (active)
[ 0.222906] pnp 00:04: Plug and Play ACPI device, IDs PNP0800 (active)
[ 0.222938] pnp 00:05: Plug and Play ACPI device, IDs PNP0c04 (active)
[ 0.222964] pnp 00:06: Plug and Play ACPI device, IDs PNP0b00 (active)
[ 0.222990] pnp 00:07: Plug and Play ACPI device, IDs PNP0303 (active)
[ 0.223017] pnp 00:08: Plug and Play ACPI device, IDs LEN0020 PNP0f13 (active)
[ 0.223061] pnp 00:09: Plug and Play ACPI device, IDs SMO1200 PNP0c31 (active)
[ 0.223534] pnp: PnP ACPI: found 10 devices
[ 0.223536] ACPI: bus type PNP unregistered
[ 0.229983] pci 0000:00:1c.0: PCI bridge to [bus 02]
[ 0.230002] pci 0000:00:1c.1: PCI bridge to [bus 03]
[ 0.230009] pci 0000:00:1c.1: bridge window [mem 0xf2400000-0xf24fffff]
[ 0.230020] pci 0000:00:1c.3: PCI bridge to [bus 05-0c]
[ 0.230023] pci 0000:00:1c.3: bridge window [io 0x4000-0x4fff]
[ 0.230029] pci 0000:00:1c.3: bridge window [mem 0xf1c00000-0xf23fffff]
[ 0.230034] pci 0000:00:1c.3: bridge window [mem 0xf0400000-0xf0bfffff 64bit pref]
[ 0.230043] pci 0000:00:1c.4: PCI bridge to [bus 0d]
[ 0.230046] pci 0000:00:1c.4: bridge window [io 0x3000-0x3fff]
[ 0.230053] pci 0000:00:1c.4: bridge window [mem 0xf1400000-0xf1bfffff]
[ 0.230058] pci 0000:00:1c.4: bridge window [mem 0xf0c00000-0xf13fffff 64bit pref]
[ 0.230067] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7]
[ 0.230068] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff]
[ 0.230069] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff]
[ 0.230071] pci_bus 0000:00: resource 7 [mem 0xdfa00000-0xfebfffff]
[ 0.230072] pci_bus 0000:00: resource 8 [mem 0xfed40000-0xfed4bfff]
[ 0.230074] pci_bus 0000:03: resource 1 [mem 0xf2400000-0xf24fffff]
[ 0.230075] pci_bus 0000:05: resource 0 [io 0x4000-0x4fff]
[ 0.230076] pci_bus 0000:05: resource 1 [mem 0xf1c00000-0xf23fffff]
[ 0.230078] pci_bus 0000:05: resource 2 [mem 0xf0400000-0xf0bfffff 64bit pref]
[ 0.230079] pci_bus 0000:0d: resource 0 [io 0x3000-0x3fff]
[ 0.230081] pci_bus 0000:0d: resource 1 [mem 0xf1400000-0xf1bfffff]
[ 0.230082] pci_bus 0000:0d: resource 2 [mem 0xf0c00000-0xf13fffff 64bit pref]
[ 0.230137] NET: Registered protocol family 2
[ 0.230308] TCP established hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.230459] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[ 0.230581] TCP: Hash tables configured (established 65536 bind 65536)
[ 0.230607] TCP: reno registered
[ 0.230617] UDP hash table entries: 4096 (order: 5, 131072 bytes)
[ 0.230646] UDP-Lite hash table entries: 4096 (order: 5, 131072 bytes)
[ 0.230733] NET: Registered protocol family 1
[ 0.230746] pci 0000:00:02.0: Boot video device
[ 0.231175] PCI: CLS 64 bytes, default 64
[ 0.231216] Unpacking initramfs...
[ 0.469133] Freeing initrd memory: 13540K (ffff88003657e000 - ffff8800372b7000)
[ 0.469137] PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
[ 0.469139] software IO TLB [mem 0xd699f000-0xda99f000] (64MB) mapped at [ffff8800d699f000-ffff8800da99efff]
[ 0.469345] RAPL PMU detected, hw unit 2^-16 Joules, API unit is 2^-32 Joules, 3 fixed counters 163840 ms ovfl timer
[ 0.469386] microcode: CPU0 sig=0x206a7, pf=0x10, revision=0x18
[ 0.469393] microcode: CPU1 sig=0x206a7, pf=0x10, revision=0x18
[ 0.469402] microcode: CPU2 sig=0x206a7, pf=0x10, revision=0x18
[ 0.469409] microcode: CPU3 sig=0x206a7, pf=0x10, revision=0x18
[ 0.469475] microcode: Microcode Update Driver: v2.00 <tigran@aivazian.fsnet.co.uk>, Peter Oruba
[ 0.469772] futex hash table entries: 2048 (order: 5, 131072 bytes)
[ 0.469826] audit: initializing netlink subsys (disabled)
[ 0.469845] audit: type=2000 audit(1411992801.468:1): initialized
[ 0.482410] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[ 0.482591] VFS: Disk quotas dquot_6.5.2
[ 0.482611] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 0.482661] msgmni has been set to 15776
[ 0.482874] alg: No test for stdrng (krng)
[ 0.482898] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[ 0.482934] io scheduler noop registered
[ 0.482936] io scheduler deadline registered
[ 0.482952] io scheduler cfq registered (default)
[ 0.483500] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 0.483514] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[ 0.483548] intel_idle: MWAIT substates: 0x21120
[ 0.483550] intel_idle: v0.4 model 0x2A
[ 0.483551] intel_idle: lapic_timer_reliable_states 0xffffffff
[ 0.483725] GHES: HEST is not enabled!
[ 0.483781] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 0.504396] 0000:00:16.3: ttyS0 at I/O 0x50b0 (irq = 19, base_baud = 115200) is a 16550A
[ 0.504550] Linux agpgart interface v0.103
[ 0.504640] i8042: PNP: PS/2 Controller [PNP0303:KBD,PNP0f13:MOU] at 0x60,0x64 irq 1,12
[ 0.507802] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 0.507806] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 0.507907] mousedev: PS/2 mouse device common for all mice
[ 0.507948] rtc_cmos 00:06: RTC can wake from S4
[ 0.508079] rtc_cmos 00:06: rtc core: registered rtc_cmos as rtc0
[ 0.508107] rtc_cmos 00:06: alarms up to one month, y3k, 114 bytes nvram, hpet irqs
[ 0.508116] Intel P-state driver initializing.
[ 0.508125] Intel pstate controlling: cpu 0
[ 0.508143] Intel pstate controlling: cpu 1
[ 0.508162] Intel pstate controlling: cpu 2
[ 0.508176] Intel pstate controlling: cpu 3
[ 0.508198] AMD IOMMUv2 driver by Joerg Roedel <joerg.roedel@amd.com>
[ 0.508199] AMD IOMMUv2 functionality not available on this system
[ 0.508290] TCP: cubic registered
[ 0.508355] NET: Registered protocol family 10
[ 0.508565] mip6: Mobile IPv6
[ 0.508567] NET: Registered protocol family 17
[ 0.508569] mpls_gso: MPLS GSO support
[ 0.508824] registered taskstats version 1
[ 0.509383] rtc_cmos 00:06: setting system clock to 2014-09-29 12:13:22 UTC (1411992802)
[ 0.509440] PM: Hibernation image not present or could not be loaded.
[ 0.509993] Freeing unused kernel memory: 1008K (ffffffff818bc000 - ffffffff819b8000)
[ 0.509995] Write protecting the kernel read-only data: 8192k
[ 0.514246] Freeing unused kernel memory: 1176K (ffff8800014da000 - ffff880001600000)
[ 0.514903] Freeing unused kernel memory: 324K (ffff8800017af000 - ffff880001800000)
[ 0.516182] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0
[ 0.523351] systemd-udevd[69]: starting version 208
[ 0.523572] random: systemd-udevd urandom read with 2 bits of entropy available
[ 0.533486] pps_core: LinuxPPS API ver. 1 registered
[ 0.533490] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 0.533693] PTP clock support registered
[ 0.534354] e1000e: Intel(R) PRO/1000 Network Driver - 2.3.2-k
[ 0.534357] e1000e: Copyright(c) 1999 - 2013 Intel Corporation.
[ 0.534358] ACPI: bus type USB registered
[ 0.534385] usbcore: registered new interface driver usbfs
[ 0.534397] usbcore: registered new interface driver hub
[ 0.534504] e1000e 0000:00:19.0: Interrupt Throttling Rate (ints/sec) set to dynamic conservative mode
[ 0.534526] e1000e 0000:00:19.0: irq 40 for MSI/MSI-X
[ 0.535290] sdhci: Secure Digital Host Controller Interface driver
[ 0.535293] sdhci: Copyright(c) Pierre Ossman
[ 0.535504] sdhci-pci 0000:0d:00.0: SDHCI controller found [1180:e822] (rev 7)
[ 0.536046] mmc0: SDHCI controller on PCI [0000:0d:00.0] using DMA
[ 0.538157] SCSI subsystem initialized
[ 0.538429] thermal LNXTHERM:00: registered as thermal_zone0
[ 0.538432] ACPI: Thermal Zone [THM0] (57 C)
[ 0.540213] libata version 3.00 loaded.
[ 0.543281] usbcore: registered new device driver usb
[ 0.543602] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 0.543725] ehci-pci: EHCI PCI platform driver
[ 0.733372] e1000e 0000:00:19.0 eth0: registered PHC clock
[ 0.733380] e1000e 0000:00:19.0 eth0: (PCI Express:2.5GT/s:Width x1) f0:de:f1:7c:02:c3
[ 0.733384] e1000e 0000:00:19.0 eth0: Intel(R) PRO/1000 Network Connection
[ 0.733440] e1000e 0000:00:19.0 eth0: MAC: 10, PHY: 11, PBA No: 1000FF-0FF
[ 0.733488] ahci 0000:00:1f.2: version 3.0
[ 0.733652] ahci 0000:00:1f.2: irq 41 for MSI/MSI-X
[ 0.733685] ahci 0000:00:1f.2: SSS flag set, parallel bus scan disabled
[ 0.748904] ahci 0000:00:1f.2: AHCI 0001.0300 32 slots 6 ports 6 Gbps 0x13 impl SATA mode
[ 0.748911] ahci 0000:00:1f.2: flags: 64bit ncq sntf ilck stag pm led clo pio slum part ems sxs apst
[ 0.766181] scsi0 : ahci
[ 0.766441] scsi1 : ahci
[ 0.766663] scsi2 : ahci
[ 0.766854] scsi3 : ahci
[ 0.767044] scsi4 : ahci
[ 0.767227] scsi5 : ahci
[ 0.767334] ata1: SATA max UDMA/133 abar m2048@0xf2528000 port 0xf2528100 irq 41
[ 0.767339] ata2: SATA max UDMA/133 abar m2048@0xf2528000 port 0xf2528180 irq 41
[ 0.767341] ata3: DUMMY
[ 0.767343] ata4: DUMMY
[ 0.767346] ata5: SATA max UDMA/133 abar m2048@0xf2528000 port 0xf2528300 irq 41
[ 0.767348] ata6: DUMMY
[ 0.767614] ehci-pci 0000:00:1a.0: EHCI Host Controller
[ 0.767625] ehci-pci 0000:00:1a.0: new USB bus registered, assigned bus number 1
[ 0.767645] ehci-pci 0000:00:1a.0: debug port 2
[ 0.771577] ehci-pci 0000:00:1a.0: cache line size of 64 is not supported
[ 0.771586] ehci-pci 0000:00:1a.0: irq 16, io mem 0xf252a000
[ 0.780795] ehci-pci 0000:00:1a.0: USB 2.0 started, EHCI 1.00
[ 0.780961] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 0.780964] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.780966] usb usb1: Product: EHCI Host Controller
[ 0.780967] usb usb1: Manufacturer: Linux 3.14-2-amd64 ehci_hcd
[ 0.780969] usb usb1: SerialNumber: 0000:00:1a.0
[ 0.781228] hub 1-0:1.0: USB hub found
[ 0.781244] hub 1-0:1.0: 3 ports detected
[ 0.781500] ehci-pci 0000:00:1d.0: EHCI Host Controller
[ 0.781506] ehci-pci 0000:00:1d.0: new USB bus registered, assigned bus number 2
[ 0.781523] ehci-pci 0000:00:1d.0: debug port 2
[ 0.785434] ehci-pci 0000:00:1d.0: cache line size of 64 is not supported
[ 0.785453] ehci-pci 0000:00:1d.0: irq 23, io mem 0xf2529000
[ 0.796809] ehci-pci 0000:00:1d.0: USB 2.0 started, EHCI 1.00
[ 0.796869] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[ 0.796872] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.796874] usb usb2: Product: EHCI Host Controller
[ 0.796876] usb usb2: Manufacturer: Linux 3.14-2-amd64 ehci_hcd
[ 0.796878] usb usb2: SerialNumber: 0000:00:1d.0
[ 0.797049] hub 2-0:1.0: USB hub found
[ 0.797062] hub 2-0:1.0: 3 ports detected
[ 1.088953] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 1.090131] ata1.00: ACPI cmd ef/02:00:00:00:00:a0 (SET FEATURES) succeeded
[ 1.090142] ata1.00: ACPI cmd f5/00:00:00:00:00:a0 (SECURITY FREEZE LOCK) filtered out
[ 1.090147] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 (SET FEATURES) filtered out
[ 1.091213] ata1.00: ATA-8: HITACHI HTS723232A7A364, EC2ZB70B, max UDMA/100
[ 1.091222] ata1.00: 625142448 sectors, multi 16: LBA48 NCQ (depth 31/32), AA
[ 1.092468] ata1.00: ACPI cmd ef/02:00:00:00:00:a0 (SET FEATURES) succeeded
[ 1.092478] ata1.00: ACPI cmd f5/00:00:00:00:00:a0 (SECURITY FREEZE LOCK) filtered out
[ 1.092483] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 (SET FEATURES) filtered out
[ 1.093057] usb 1-1: new high-speed USB device number 2 using ehci-pci
[ 1.093625] ata1.00: configured for UDMA/100
[ 1.094059] scsi 0:0:0:0: Direct-Access ATA HITACHI HTS72323 EC2Z PQ: 0 ANSI: 5
[ 1.225845] usb 1-1: New USB device found, idVendor=8087, idProduct=0024
[ 1.225854] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 1.226590] hub 1-1:1.0: USB hub found
[ 1.226915] hub 1-1:1.0: 6 ports detected
[ 1.340957] usb 2-1: new high-speed USB device number 2 using ehci-pci
[ 1.413003] ata2: SATA link down (SStatus 0 SControl 300)
[ 1.469007] tsc: Refined TSC clocksource calibration: 2491.909 MHz
[ 1.473739] usb 2-1: New USB device found, idVendor=8087, idProduct=0024
[ 1.473748] usb 2-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 1.474335] hub 2-1:1.0: USB hub found
[ 1.474525] hub 2-1:1.0: 8 ports detected
[ 1.549294] usb 1-1.4: new full-speed USB device number 3 using ehci-pci
[ 1.648155] usb 1-1.4: New USB device found, idVendor=0a5c, idProduct=217f
[ 1.648164] usb 1-1.4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 1.648169] usb 1-1.4: Product: Broadcom Bluetooth Device
[ 1.648172] usb 1-1.4: Manufacturer: Broadcom Corp
[ 1.648176] usb 1-1.4: SerialNumber: CCAF78EEDB01
[ 1.721318] usb 1-1.6: new high-speed USB device number 4 using ehci-pci
[ 1.741049] ata5: SATA link down (SStatus 0 SControl 300)
[ 1.747975] sd 0:0:0:0: [sda] 625142448 512-byte logical blocks: (320 GB/298 GiB)
[ 1.748072] sd 0:0:0:0: [sda] Write Protect is off
[ 1.748081] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 1.748137] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1.805378] sda: sda1 sda2 < sda5 >
[ 1.806401] sd 0:0:0:0: [sda] Attached SCSI disk
[ 1.807555] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 1.820628] usb 1-1.6: New USB device found, idVendor=04f2, idProduct=b217
[ 1.820636] usb 1-1.6: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 1.820641] usb 1-1.6: Product: Integrated Camera
[ 1.820644] usb 1-1.6: Manufacturer: Chicony Electronics Co., Ltd.
[ 2.065505] PM: Starting manual resume from disk
[ 2.065515] PM: Hibernation image partition 8:5 present
[ 2.065518] PM: Looking for hibernation image.
[ 2.065816] PM: Image not found (code -22)
[ 2.065819] PM: Hibernation image not present or could not be loaded.
[ 2.115119] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
[ 2.469450] Switched to clocksource tsc
[ 2.940370] systemd[1]: systemd 208 running in system mode. (+PAM +LIBWRAP +AUDIT +SELINUX +IMA +SYSVINIT +LIBCRYPTSETUP +GCRYPT +ACL +XZ)
[ 3.175701] systemd[1]: Inserted module 'autofs4'
[ 3.188790] systemd[1]: Set hostname to <core01>.
[ 3.480387] random: nonblocking pool is initialized
[ 4.099027] systemd[1]: Starting Syslog Socket.
[ 4.099115] systemd[1]: Listening on Syslog Socket.
[ 4.099144] systemd[1]: Starting Forward Password Requests to Wall Directory Watch.
[ 4.099248] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
[ 4.099269] systemd[1]: Starting Remote File Systems (Pre).
[ 4.099289] systemd[1]: Reached target Remote File Systems (Pre).
[ 4.099306] systemd[1]: Starting Delayed Shutdown Socket.
[ 4.099345] systemd[1]: Listening on Delayed Shutdown Socket.
[ 4.099362] systemd[1]: Starting /dev/initctl Compatibility Named Pipe.
[ 4.099410] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe.
[ 4.099435] systemd[1]: Starting Dispatch Password Requests to Console Directory Watch.
[ 4.099489] systemd[1]: Started Dispatch Password Requests to Console Directory Watch.
[ 4.099507] systemd[1]: Starting Paths.
[ 4.099524] systemd[1]: Reached target Paths.
[ 4.099547] systemd[1]: Starting udev Kernel Socket.
[ 4.099579] systemd[1]: Listening on udev Kernel Socket.
[ 4.099600] systemd[1]: Starting udev Control Socket.
[ 4.099635] systemd[1]: Listening on udev Control Socket.
[ 4.099652] systemd[1]: Starting Encrypted Volumes.
[ 4.099668] systemd[1]: Reached target Encrypted Volumes.
[ 4.099718] systemd[1]: Starting Arbitrary Executable File Formats File System Automount Point.
[ 4.099874] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point.
[ 4.099898] systemd[1]: Starting Journal Socket.
[ 4.099967] systemd[1]: Listening on Journal Socket.
[ 4.100000] systemd[1]: Mounting POSIX Message Queue File System...
[ 4.100887] systemd[1]: Starting Create list of required static device nodes for the current kernel...
[ 4.161282] systemd[1]: Started Set Up Additional Binary Formats.
[ 4.161390] systemd[1]: Starting udev Coldplug all Devices...
[ 4.162091] systemd[1]: Starting Syslog.
[ 4.162114] systemd[1]: Reached target Syslog.
[ 4.162156] systemd[1]: Starting Journal Service...
[ 4.162822] systemd[1]: Started Journal Service.
[ 4.383347] fuse init (API version 7.22)
[ 5.409081] systemd-udevd[179]: starting version 208
[ 7.017964] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 7.026996] i801_smbus 0000:00:1f.3: SMBus using PCI Interrupt
[ 7.049793] input: Lid Switch as /devices/LNXSYSTM:00/device:00/PNP0C0D:00/input/input2
[ 7.051694] ACPI: Lid Switch [LID]
[ 7.051773] input: Sleep Button as /devices/LNXSYSTM:00/device:00/PNP0C0E:00/input/input3
[ 7.051777] ACPI: Sleep Button [SLPB]
[ 7.051839] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input4
[ 7.051861] ACPI: Power Button [PWRF]
[ 7.054836] ACPI: Battery Slot [BAT0] (battery present)
[ 7.093109] tpm_tis 00:09: 1.2 TPM (device-id 0x0, rev-id 78)
[ 7.131508] ACPI: AC Adapter [AC] (on-line)
[ 7.185558] input: PC Speaker as /devices/platform/pcspkr/input/input5
[ 7.290526] wmi: Mapper loaded
[ 7.301088] mei_me 0000:00:16.0: irq 42 for MSI/MSI-X
[ 7.306349] ACPI Warning: SystemIO range 0x0000000000000428-0x000000000000042f conflicts with OpRegion 0x0000000000000400-0x000000000000047f (\_SB_.PCI0.LPC_.PMIO) (20131218/utaddress-258)
[ 7.306356] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[ 7.306377] ACPI Warning: SystemIO range 0x0000000000000540-0x000000000000054f conflicts with OpRegion 0x0000000000000500-0x000000000000057f (\_SB_.PCI0.LPC_.LPIO) (20131218/utaddress-258)
[ 7.306380] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[ 7.306382] ACPI Warning: SystemIO range 0x0000000000000530-0x000000000000053f conflicts with OpRegion 0x0000000000000500-0x000000000000057f (\_SB_.PCI0.LPC_.LPIO) (20131218/utaddress-258)
[ 7.306385] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[ 7.306386] ACPI Warning: SystemIO range 0x0000000000000500-0x000000000000052f conflicts with OpRegion 0x0000000000000500-0x000000000000057f (\_SB_.PCI0.LPC_.LPIO) (20131218/utaddress-258)
[ 7.306389] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[ 7.306390] lpc_ich: Resource conflict(s) found affecting gpio_ich
[ 7.402854] [drm] Initialized drm 1.1.0 20060810
[ 7.419054] iTCO_vendor_support: vendor-support=0
[ 7.419389] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.10
[ 7.419420] iTCO_wdt: Found a Cougar Point TCO device (Version=2, TCOBASE=0x0460)
[ 7.419479] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[ 7.813508] Non-volatile memory driver v1.3
[ 7.838415] thinkpad_acpi: ThinkPad ACPI Extras v0.25
[ 7.838422] thinkpad_acpi: http://ibm-acpi.sf.net/
[ 7.838425] thinkpad_acpi: ThinkPad BIOS 8DET50WW (1.20 ), EC unknown
[ 7.838428] thinkpad_acpi: Lenovo ThinkPad X220, model 4290A11
[ 7.839136] thinkpad_acpi: detected a 16-level brightness capable ThinkPad
[ 7.839322] thinkpad_acpi: radio switch found; radios are enabled
[ 7.839487] thinkpad_acpi: possible tablet mode switch found; ThinkPad in laptop mode
[ 7.839715] thinkpad_acpi: This ThinkPad has standard ACPI backlight brightness control, supported by the ACPI video driver
[ 7.839720] thinkpad_acpi: Disabling thinkpad-acpi brightness events by default...
[ 7.842540] thinkpad_acpi: rfkill switch tpacpi_bluetooth_sw: radio is unblocked
[ 7.843197] thinkpad_acpi: Standard ACPI backlight interface available, not loading native one
[ 7.843373] thinkpad_acpi: Console audio control enabled, mode: monitor (read only)
[ 7.846282] input: ThinkPad Extra Buttons as /devices/platform/thinkpad_acpi/input/input7
[ 7.874998] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro
[ 7.876920] [drm] Memory usable by graphics device = 2048M
[ 7.902072] i915 0000:00:02.0: irq 43 for MSI/MSI-X
[ 7.902371] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[ 7.902373] [drm] Driver supports precise vblank timestamp query.
[ 7.902469] vgaarb: device changed decodes: PCI:0000:00:02.0,olddecodes=io+mem,decodes=io+mem:owns=io+mem
[ 7.950365] [drm] Wrong MCH_SSKPD value: 0x16040307
[ 7.950370] [drm] This can cause pipe underruns and display issues.
[ 7.950372] [drm] Please upgrade your BIOS to fix this.
[ 8.022012] [drm] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 5
[ 8.039271] fbcon: inteldrmfb (fb0) is primary device
[ 8.188128] psmouse serio1: synaptics: Touchpad model: 1, fw: 8.0, id: 0x1e2b1, caps: 0xd001a3/0x940300/0x120c00, board id: 1611, fw id: 774180
[ 8.188145] psmouse serio1: synaptics: serio: Synaptics pass-through port at isa0060/serio1/input0
[ 8.218774] AVX version of gcm_enc/dec engaged.
[ 8.222333] alg: No test for __gcm-aes-aesni (__driver-gcm-aes-aesni)
[ 8.238345] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio1/input/input6
[ 8.463420] Bluetooth: Core ver 2.18
[ 8.463459] NET: Registered protocol family 31
[ 8.463460] Bluetooth: HCI device and connection manager initialized
[ 8.463469] Bluetooth: HCI socket layer initialized
[ 8.463471] Bluetooth: L2CAP socket layer initialized
[ 8.463485] Bluetooth: SCO socket layer initialized
[ 8.579240] cfg80211: Calling CRDA to update world regulatory domain
[ 8.656662] systemd-journald[155]: Received request to flush runtime journal from PID 1
[ 8.684573] usbcore: registered new interface driver btusb
[ 8.772628] Console: switching to colour frame buffer device 170x48
[ 8.778589] i915 0000:00:02.0: fb0: inteldrmfb frame buffer device
[ 8.778592] i915 0000:00:02.0: registered panic notifier
[ 8.814796] ACPI: Video Device [VID] (multi-head: yes rom: no post: no)
[ 8.831678] acpi device:01: registered as cooling_device4
[ 8.831784] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/LNXVIDEO:00/input/input9
[ 8.832217] [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0
[ 8.832831] snd_hda_intel 0000:00:1b.0: irq 44 for MSI/MSI-X
[ 8.887029] alg: No test for crc32 (crc32-pclmul)
[ 8.967302] systemd-journald[155]: Received request to flush runtime journal from PID 1
[ 9.090415] Intel(R) Wireless WiFi driver for Linux, in-tree:
[ 9.090421] Copyright(c) 2003- 2014 Intel Corporation
[ 9.090671] iwlwifi 0000:03:00.0: can't disable ASPM; OS doesn't have ASPM control
[ 9.090893] iwlwifi 0000:03:00.0: irq 45 for MSI/MSI-X
[ 9.105325] iwlwifi 0000:03:00.0: firmware: failed to load iwlwifi-6000g2a-6.ucode (-2)
[ 9.105411] iwlwifi 0000:03:00.0: Direct firmware load failed with error -2
[ 9.105414] iwlwifi 0000:03:00.0: Falling back to user helper
[ 9.125634] iwlwifi 0000:03:00.0: firmware: direct-loading firmware iwlwifi-6000g2a-5.ucode
[ 9.125829] iwlwifi 0000:03:00.0: loaded firmware version 17.168.5.1 build 33993 op_mode iwldvm
[ 9.202754] iwlwifi 0000:03:00.0: CONFIG_IWLWIFI_DEBUG disabled
[ 9.202764] iwlwifi 0000:03:00.0: CONFIG_IWLWIFI_DEBUGFS disabled
[ 9.202770] iwlwifi 0000:03:00.0: CONFIG_IWLWIFI_DEVICE_TRACING disabled
[ 9.202776] iwlwifi 0000:03:00.0: Detected Intel(R) Centrino(R) Advanced-N 6205 AGN, REV=0xB0
[ 9.202878] iwlwifi 0000:03:00.0: L1 Enabled; Disabling L0S
[ 9.301160] media: Linux media interface: v0.10
[ 9.320599] Linux video capture interface: v2.00
[ 9.331463] hda_codec: CX20590: BIOS auto-probing.
[ 9.332974] input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:1b.0/input/input10
[ 9.502160] kvm: disabled by bios
[ 9.511160] kvm: disabled by bios
[ 9.534816] kvm: disabled by bios
[ 9.567482] kvm: disabled by bios
[ 9.618658] ieee80211 phy0: Selected rate control algorithm 'iwl-agn-rs'
[ 9.643876] input: HDA Intel PCH HDMI/DP,pcm=8 as /devices/pci0000:00/0000:00:1b.0/sound/card0/input17
[ 9.643955] input: HDA Intel PCH HDMI/DP,pcm=7 as /devices/pci0000:00/0000:00:1b.0/sound/card0/input16
[ 9.644009] input: HDA Intel PCH HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:1b.0/sound/card0/input15
[ 9.644060] input: HDA Intel PCH Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input14
[ 9.644109] input: HDA Intel PCH Dock Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input13
[ 9.644158] input: HDA Intel PCH Dock Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input12
[ 9.644206] input: HDA Intel PCH Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input11
[ 9.794680] [drm] Enabling RC6 states: RC6 on, RC6p off, RC6pp off
[ 10.022162] uvcvideo: Found UVC 1.00 device Integrated Camera (04f2:b217)
[ 10.024974] input: Integrated Camera as /devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.6/1-1.6:1.0/input/input18
[ 10.025141] usbcore: registered new interface driver uvcvideo
[ 10.025145] USB Video Class driver (1.1.1)
[ 10.346763] cfg80211: World regulatory domain updated:
[ 10.346767] cfg80211: DFS Master region: unset
[ 10.346768] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 10.346770] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[ 10.346772] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[ 10.346773] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm)
[ 10.346774] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm)
[ 10.346775] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm)
[ 10.346776] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm)
[ 10.741616] Adding 12683260k swap on /dev/sda5. Priority:-1 extents:1 across:12683260k
[ 11.734533] RPC: Registered named UNIX socket transport module.
[ 11.734541] RPC: Registered udp transport module.
[ 11.734543] RPC: Registered tcp transport module.
[ 11.734545] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 11.778586] FS-Cache: Loaded
[ 11.797374] psmouse serio2: alps: Unknown ALPS touchpad: E7=10 00 64, EC=10 00 64
[ 11.806410] FS-Cache: Netfs 'nfs' registered for caching
[ 11.856292] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 13.323916] psmouse serio2: trackpoint: IBM TrackPoint firmware: 0x0e, buttons: 3/3
[ 13.576951] input: TPPS/2 IBM TrackPoint as /devices/platform/i8042/serio1/serio2/input/input8
[ 15.002641] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 15.002651] Bluetooth: BNEP filters: protocol multicast
[ 15.002668] Bluetooth: BNEP socket layer initialized
[ 16.800017] e1000e 0000:00:19.0: irq 40 for MSI/MSI-X
[ 16.903599] e1000e 0000:00:19.0: irq 40 for MSI/MSI-X
[ 16.903848] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 18.393735] e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: Rx/Tx
[ 18.393750] e1000e 0000:00:19.0 eth0: 10/100 speed: disabling TSO
[ 18.393795] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 47.472351] iwlwifi 0000:03:00.0: L1 Enabled; Disabling L0S
[ 47.472569] iwlwifi 0000:03:00.0: Radio type=0x1-0x2-0x0
[ 47.740136] iwlwifi 0000:03:00.0: L1 Enabled; Disabling L0S
[ 47.740355] iwlwifi 0000:03:00.0: Radio type=0x1-0x2-0x0
[ 47.848504] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 49.147163] iwlwifi 0000:03:00.0: failed to remove IBSS station ba:b6:e2:b3:da:0f
[ 51.829621] wlan0: Trigger new scan to find an IBSS to join
[ 52.104138] wlan0: Selected IBSS BSSID ba:b6:e2:b3:da:0f based on configured SSID
[ 52.127811] iwlwifi 0000:03:00.0: Unable to find TIM Element in beacon
[ 52.130359] iwlwifi 0000:03:00.0: Unable to find TIM Element in beacon
[ 52.130636] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
next reply other threads:[~2014-09-29 13:38 UTC|newest]
Thread overview: 5+ messages / expand[flat|nested] mbox.gz Atom feed top
2014-09-29 13:27 Martin Hundebøll [this message]
2014-11-12 6:26 ` [PATCH] iwlwifi: dvm: Implement sta_rc_update() mac80211 callback David Ward
2014-11-12 14:01 ` Grumbach, Emmanuel
2014-11-12 14:30 ` Michal Kazior
2014-11-12 14:31 ` Grumbach, Emmanuel
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1411997268.1663.0@smtp.hundeboll.net \
--to=martin@hundeboll.net \
--cc=johannes@sipsolutions.net \
--cc=linux-wireless@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.