[PATCH V9 00/10] usb: serial: F81232 V9 patches

[PATCH V9 00/10] usb: serial: F81232 V9 patches

[Peter Hung]

This series patch V9 is changed from V8 as following:

1. add comments for read URB 1byte LSR when port open.
2. change error handle flow of set_register()/get_register()

V8 (old change):
1. The V7 MSR strange delta value is checked with locking problem. We changed
   f81232_set_mctrl() & f81232_read_msr() lock mechanism, the old version is
   only locked with variable protection, new version will lock from start to
   end with these 2 function.   
2. f81232_set_baudrate() add error handling and no longer handle with baudrate
   B0, change to handle with f81232_set_termios()
3. When user set baudrate larger then 115200, we will change it with 115200
   and tty_encode_baud_rate() in f81232_set_termios().
4. V7 f81232_set_baudrate() divisor declared with type u8, it will make 
   baudrate set failed with smaller then B600 (115200/300=384 overflow :Q).
   We changed it with integer type for divisor larger then 256.
   
V7 (old change):

1. The buffer of usb_control_msg() in set_register()/get_register() are change
   from local variable to kmalloc(). (PATCH V7 02/11)
2. Change all set_register()/get_register() return value 0 is success, 
   otherwise are failed. ( return 0 of usb_control_msg() treat as -EIO, 
   PATCH V7 02/11)
3. tty_port_tty_get() called only when DCD has changed. (PATCH V7 05/11)  
4. remove likely()/unlikely() branch prediction.
5. Implement DTR/RTS control when baudrate B0. We drop DTR/RTS when B0, 
   otherwise enable it. (PATCH V7 08/11)
6. Change private struct line_control to modem_control with meanful. 
   (PATCH V7 06/11)
7. We confirmd MSR strange delta value is not locking-issue. The issue
   maybe reproduce with set MCR & get MSR before IIR notice with MSR changed.
   
V6 (old change):

1. transform all function not to use private data as parameter, using
   usb_serial_port instead.
2. process_read_urb() add process of Break/FrameError/ParityError/OE.
   (patch: 03/10)
3. fix calc_baud_divisor() will cause divide by zero with B0. (patch: 04/10)
4. Some init step we extract it from set_termios() to f81232_port_init()
   and run it when open port only. (patch: 04/10)
5. We'll force re-read msr in tiocmget() because the IIR with MSR change
   maybe delay received. (patch: 05/10)
6. fix MSR status bits changed but delta bits is 0 will cause read serial port
   malfunctional with update port status. (patch: 08/10)
7. Add MSR change statistic when MSR has been read. (patch: 09/10)   
8. clarify a lot of code about Johan suggested.

Peter Hung (10):
  USB: f81232: rename private struct member name
  USB: f81232: implement RX bulk-in EP
  USB: f81232: change lock mechanism
  USB: f81232: implement read IIR/MSR with endpoint
  USB: f81232: implement MCR/MSR function
  USB: f81232: implement port enable/disable method
  USB: f81232: implement set_termios()
  USB: f81232: clarify f81232_ioctl() and fix
  USB: f81232: cleanup non-used define
  USB: f81232: modify/add author

 drivers/usb/serial/f81232.c | 555 ++++++++++++++++++++++++++++++++++++--------
 1 file changed, 457 insertions(+), 98 deletions(-)

-- 
1.9.1

[PATCH V9 01/10] USB: f81232: rename private struct member name

[Peter Hung]

Change private struct member name from line_status to modem_status.
It will store MSR for some functions used

Signed-off-by: Peter Hung <hpeter+linux_kernel@gmail.com>
---
 drivers/usb/serial/f81232.c | 8 ++++----
 1 file changed, 4 insertions(+), 4 deletions(-)

diff --git a/drivers/usb/serial/f81232.c b/drivers/usb/serial/f81232.c
index c5dc233..669a2f2 100644
--- a/drivers/usb/serial/f81232.c
+++ b/drivers/usb/serial/f81232.c
@@ -47,7 +47,7 @@ MODULE_DEVICE_TABLE(usb, id_table);
 struct f81232_private {
 	spinlock_t lock;
 	u8 line_control;
-	u8 line_status;
+	u8 modem_status;
 };
 
 static void f81232_update_line_status(struct usb_serial_port *port,
@@ -113,8 +113,8 @@ static void f81232_process_read_urb(struct urb *urb)
 
 	/* update line status */
 	spin_lock_irqsave(&priv->lock, flags);
-	line_status = priv->line_status;
-	priv->line_status &= ~UART_STATE_TRANSIENT_MASK;
+	line_status = priv->modem_status;
+	priv->modem_status &= ~UART_STATE_TRANSIENT_MASK;
 	spin_unlock_irqrestore(&priv->lock, flags);
 
 	if (!urb->actual_length)
@@ -241,7 +241,7 @@ static void f81232_dtr_rts(struct usb_serial_port *port, int on)
 static int f81232_carrier_raised(struct usb_serial_port *port)
 {
 	struct f81232_private *priv = usb_get_serial_port_data(port);
-	if (priv->line_status & UART_DCD)
+	if (priv->modem_status & UART_DCD)
 		return 1;
 	return 0;
 }
-- 
1.9.1

[PATCH V9 02/10] USB: f81232: implement RX bulk-in EP

[Peter Hung]

The F81232 bulk-in is RX data + LSR channel, data format is
[LSR+Data][LSR+Data]..... , We had implemented in f81232_process_read_urb().

Signed-off-by: Peter Hung <hpeter+linux_kernel@gmail.com>
---
 drivers/usb/serial/f81232.c | 73 +++++++++++++++++++++++++--------------------
 1 file changed, 40 insertions(+), 33 deletions(-)

diff --git a/drivers/usb/serial/f81232.c b/drivers/usb/serial/f81232.c
index 669a2f2..6b83870b 100644
--- a/drivers/usb/serial/f81232.c
+++ b/drivers/usb/serial/f81232.c
@@ -23,6 +23,7 @@
 #include <linux/uaccess.h>
 #include <linux/usb.h>
 #include <linux/usb/serial.h>
+#include <linux/serial_reg.h>
 
 static const struct usb_device_id id_table[] = {
 	{ USB_DEVICE(0x1934, 0x0706) },
@@ -104,44 +105,50 @@ exit:
 static void f81232_process_read_urb(struct urb *urb)
 {
 	struct usb_serial_port *port = urb->context;
-	struct f81232_private *priv = usb_get_serial_port_data(port);
 	unsigned char *data = urb->transfer_buffer;
-	char tty_flag = TTY_NORMAL;
-	unsigned long flags;
-	u8 line_status;
-	int i;
+	char tty_flag;
+	unsigned int i;
+	u8 lsr;
 
-	/* update line status */
-	spin_lock_irqsave(&priv->lock, flags);
-	line_status = priv->modem_status;
-	priv->modem_status &= ~UART_STATE_TRANSIENT_MASK;
-	spin_unlock_irqrestore(&priv->lock, flags);
+	/* It's had 1-byte packet on open, the data is current LSR. but
+	 * in this situation, the byte useless for open.
+	 */
 
-	if (!urb->actual_length)
+	if ((urb->actual_length < 2) || (urb->actual_length % 2))
 		return;
 
-	/* break takes precedence over parity, */
-	/* which takes precedence over framing errors */
-	if (line_status & UART_BREAK_ERROR)
-		tty_flag = TTY_BREAK;
-	else if (line_status & UART_PARITY_ERROR)
-		tty_flag = TTY_PARITY;
-	else if (line_status & UART_FRAME_ERROR)
-		tty_flag = TTY_FRAME;
-	dev_dbg(&port->dev, "%s - tty_flag = %d\n", __func__, tty_flag);
-
-	/* overrun is special, not associated with a char */
-	if (line_status & UART_OVERRUN_ERROR)
-		tty_insert_flip_char(&port->port, 0, TTY_OVERRUN);
-
-	if (port->port.console && port->sysrq) {
-		for (i = 0; i < urb->actual_length; ++i)
-			if (!usb_serial_handle_sysrq_char(port, data[i]))
-				tty_insert_flip_char(&port->port, data[i],
-						tty_flag);
-	} else {
-		tty_insert_flip_string_fixed_flag(&port->port, data, tty_flag,
-							urb->actual_length);
+	/* bulk-in data: [LSR(1Byte)+DATA(1Byte)][LSR(1Byte)+DATA(1Byte)]... */
+
+	for (i = 0; i < urb->actual_length; i += 2) {
+		tty_flag = TTY_NORMAL;
+		lsr = data[i];
+
+		if (lsr & UART_LSR_BRK_ERROR_BITS) {
+			if (lsr & UART_LSR_BI) {
+				tty_flag = TTY_BREAK;
+				port->icount.brk++;
+				usb_serial_handle_break(port);
+			} else if (lsr & UART_LSR_PE) {
+				tty_flag = TTY_PARITY;
+				port->icount.parity++;
+			} else if (lsr & UART_LSR_FE) {
+				tty_flag = TTY_FRAME;
+				port->icount.frame++;
+			}
+
+			if (lsr & UART_LSR_OE) {
+				port->icount.overrun++;
+				tty_insert_flip_char(&port->port, 0,
+						TTY_OVERRUN);
+			}
+		}
+
+		if (port->port.console && port->sysrq) {
+			if (usb_serial_handle_sysrq_char(port, data[i + 1]))
+				continue;
+		}
+
+		tty_insert_flip_char(&port->port, data[i + 1], tty_flag);
 	}
 
 	tty_flip_buffer_push(&port->port);
-- 
1.9.1

Re: [PATCH V9 02/10] USB: f81232: implement RX bulk-in EP

[Johan Hovold]

On Tue, Mar 17, 2015 at 05:48:20PM +0800, Peter Hung wrote:
> The F81232 bulk-in is RX data + LSR channel, data format is
> [LSR+Data][LSR+Data]..... , We had implemented in f81232_process_read_urb().
> 
> Signed-off-by: Peter Hung <hpeter+linux_kernel@gmail.com>

>  static void f81232_process_read_urb(struct urb *urb)
>  {
>  	struct usb_serial_port *port = urb->context;
> -	struct f81232_private *priv = usb_get_serial_port_data(port);
>  	unsigned char *data = urb->transfer_buffer;
> -	char tty_flag = TTY_NORMAL;
> -	unsigned long flags;
> -	u8 line_status;
> -	int i;
> +	char tty_flag;
> +	unsigned int i;
> +	u8 lsr;
>  
> -	/* update line status */
> -	spin_lock_irqsave(&priv->lock, flags);
> -	line_status = priv->modem_status;
> -	priv->modem_status &= ~UART_STATE_TRANSIENT_MASK;
> -	spin_unlock_irqrestore(&priv->lock, flags);
> +	/* It's had 1-byte packet on open, the data is current LSR. but
> +	 * in this situation, the byte useless for open.
> +	 */

I'll change this comment to

	/*
	 * When opening the port we get a 1-byte packet with the current LSR,
	 * which we discard.
	 */

before applying. Let me know if I managed to get it wrong.

>  
> -	if (!urb->actual_length)
> +	if ((urb->actual_length < 2) || (urb->actual_length % 2))
>  		return;

I'll apply the whole series now. Thanks again for fixing up this driver!

Johan

Re: [PATCH V9 02/10] USB: f81232: implement RX bulk-in EP

[Peter Hung]

Hello,

Thanks for your kindly support and code review.
It's my honor to work with you :D


Johan Hovold 於 2015/3/28 上午 12:17 寫道:

> I'll apply the whole series now. Thanks again for fixing up this driver!
>
> Johan
>

-- 
With Best Regards,
Peter Hung

[PATCH V9 03/10] USB: f81232: change lock mechanism

[Peter Hung]

The original driver lock with spin_lock_irqsave()/spin_unlock_irqrestore()
because of it's maybe used in interrupt context f81232_process_read_urb().

We had remove it from previous patch "implement RX bulk-in EP", so we can
change it from busying loop spin_lock to sleepable mutex_lock.

Signed-off-by: Peter Hung <hpeter+linux_kernel@gmail.com>
---
 drivers/usb/serial/f81232.c | 11 +++++------
 1 file changed, 5 insertions(+), 6 deletions(-)

diff --git a/drivers/usb/serial/f81232.c b/drivers/usb/serial/f81232.c
index 6b83870b..61a6a1a 100644
--- a/drivers/usb/serial/f81232.c
+++ b/drivers/usb/serial/f81232.c
@@ -19,7 +19,7 @@
 #include <linux/serial.h>
 #include <linux/module.h>
 #include <linux/moduleparam.h>
-#include <linux/spinlock.h>
+#include <linux/mutex.h>
 #include <linux/uaccess.h>
 #include <linux/usb.h>
 #include <linux/usb/serial.h>
@@ -46,7 +46,7 @@ MODULE_DEVICE_TABLE(usb, id_table);
 #define UART_CTS			0x80
 
 struct f81232_private {
-	spinlock_t lock;
+	struct mutex lock;
 	u8 line_control;
 	u8 modem_status;
 };
@@ -231,17 +231,16 @@ static void f81232_close(struct usb_serial_port *port)
 static void f81232_dtr_rts(struct usb_serial_port *port, int on)
 {
 	struct f81232_private *priv = usb_get_serial_port_data(port);
-	unsigned long flags;
 	u8 control;
 
-	spin_lock_irqsave(&priv->lock, flags);
+	mutex_lock(&priv->lock);
 	/* Change DTR and RTS */
 	if (on)
 		priv->line_control |= (CONTROL_DTR | CONTROL_RTS);
 	else
 		priv->line_control &= ~(CONTROL_DTR | CONTROL_RTS);
 	control = priv->line_control;
-	spin_unlock_irqrestore(&priv->lock, flags);
+	mutex_unlock(&priv->lock);
 	set_control_lines(port->serial->dev, control);
 }
 
@@ -285,7 +284,7 @@ static int f81232_port_probe(struct usb_serial_port *port)
 	if (!priv)
 		return -ENOMEM;
 
-	spin_lock_init(&priv->lock);
+	mutex_init(&priv->lock);
 
 	usb_set_serial_port_data(port, priv);
 
-- 
1.9.1

[PATCH V9 04/10] USB: f81232: implement read IIR/MSR with endpoint

[Peter Hung]

The interrupt endpoint will report current IIR. If we got IIR with MSR changed
, We will do read MSR with interrupt_work worker to do f81232_read_msr()
function.

Signed-off-by: Peter Hung <hpeter+linux_kernel@gmail.com>
---
 drivers/usb/serial/f81232.c | 126 +++++++++++++++++++++++++++++++++++++++++---
 1 file changed, 118 insertions(+), 8 deletions(-)

diff --git a/drivers/usb/serial/f81232.c b/drivers/usb/serial/f81232.c
index 61a6a1a..1e1261f 100644
--- a/drivers/usb/serial/f81232.c
+++ b/drivers/usb/serial/f81232.c
@@ -31,6 +31,13 @@ static const struct usb_device_id id_table[] = {
 };
 MODULE_DEVICE_TABLE(usb, id_table);
 
+/* USB Control EP parameter */
+#define F81232_REGISTER_REQUEST	0xa0
+#define F81232_GET_REGISTER		0xc0
+
+#define SERIAL_BASE_ADDRESS			0x0120
+#define MODEM_STATUS_REGISTER		(0x06 + SERIAL_BASE_ADDRESS)
+
 #define CONTROL_DTR			0x01
 #define CONTROL_RTS			0x02
 
@@ -49,19 +56,112 @@ struct f81232_private {
 	struct mutex lock;
 	u8 line_control;
 	u8 modem_status;
+	struct work_struct interrupt_work;
+	struct usb_serial_port *port;
 };
 
+static int f81232_get_register(struct usb_serial_port *port, u16 reg, u8 *val)
+{
+	int status;
+	u8 *tmp;
+	struct usb_device *dev = port->serial->dev;
+
+	tmp = kmalloc(sizeof(*val), GFP_KERNEL);
+	if (!tmp)
+		return -ENOMEM;
+
+	status = usb_control_msg(dev,
+				usb_rcvctrlpipe(dev, 0),
+				F81232_REGISTER_REQUEST,
+				F81232_GET_REGISTER,
+				reg,
+				0,
+				tmp,
+				sizeof(*val),
+				USB_CTRL_GET_TIMEOUT);
+	if (status != sizeof(*val)) {
+		dev_err(&port->dev, "%s failed status: %d\n", __func__, status);
+
+		if (status < 0)
+			status = usb_translate_errors(status);
+		else
+			status = -EIO;
+	} else {
+		status = 0;
+		*val = *tmp;
+	}
+
+	kfree(tmp);
+	return status;
+}
+
+static void f81232_read_msr(struct usb_serial_port *port)
+{
+	int status;
+	u8 current_msr;
+	struct tty_struct *tty;
+	struct f81232_private *priv = usb_get_serial_port_data(port);
+
+	mutex_lock(&priv->lock);
+	status = f81232_get_register(port, MODEM_STATUS_REGISTER,
+			&current_msr);
+	if (status) {
+		dev_err(&port->dev, "%s fail, status: %d\n", __func__, status);
+		mutex_unlock(&priv->lock);
+		return;
+	}
+
+	if (!(current_msr & UART_MSR_ANY_DELTA)) {
+		mutex_unlock(&priv->lock);
+		return;
+	}
+
+	priv->modem_status = current_msr;
+
+	if (current_msr & UART_MSR_DCTS)
+		port->icount.cts++;
+	if (current_msr & UART_MSR_DDSR)
+		port->icount.dsr++;
+	if (current_msr & UART_MSR_TERI)
+		port->icount.rng++;
+	if (current_msr & UART_MSR_DDCD) {
+		port->icount.dcd++;
+		tty = tty_port_tty_get(&port->port);
+		if (tty) {
+			usb_serial_handle_dcd_change(port, tty,
+					current_msr & UART_MSR_DCD);
+
+			tty_kref_put(tty);
+		}
+	}
+
+	wake_up_interruptible(&port->port.delta_msr_wait);
+	mutex_unlock(&priv->lock);
+}
+
 static void f81232_update_line_status(struct usb_serial_port *port,
 				      unsigned char *data,
-				      unsigned int actual_length)
+				      size_t actual_length)
 {
-	/*
-	 * FIXME: Update port->icount, and call
-	 *
-	 *		wake_up_interruptible(&port->port.delta_msr_wait);
-	 *
-	 *	  on MSR changes.
-	 */
+	struct f81232_private *priv = usb_get_serial_port_data(port);
+
+	if (!actual_length)
+		return;
+
+	switch (data[0] & 0x07) {
+	case 0x00: /* msr change */
+		dev_dbg(&port->dev, "IIR: MSR Change: %02x\n", data[0]);
+		schedule_work(&priv->interrupt_work);
+		break;
+	case 0x02: /* tx-empty */
+		break;
+	case 0x04: /* rx data available */
+		break;
+	case 0x06: /* lsr change */
+		/* we can forget it. the LSR will read from bulk-in */
+		dev_dbg(&port->dev, "IIR: LSR Change: %02x\n", data[0]);
+		break;
+	}
 }
 
 static void f81232_read_int_callback(struct urb *urb)
@@ -276,6 +376,14 @@ static int f81232_ioctl(struct tty_struct *tty,
 	return -ENOIOCTLCMD;
 }
 
+static void  f81232_interrupt_work(struct work_struct *work)
+{
+	struct f81232_private *priv =
+		container_of(work, struct f81232_private, interrupt_work);
+
+	f81232_read_msr(priv->port);
+}
+
 static int f81232_port_probe(struct usb_serial_port *port)
 {
 	struct f81232_private *priv;
@@ -285,10 +393,12 @@ static int f81232_port_probe(struct usb_serial_port *port)
 		return -ENOMEM;
 
 	mutex_init(&priv->lock);
+	INIT_WORK(&priv->interrupt_work,  f81232_interrupt_work);
 
 	usb_set_serial_port_data(port, priv);
 
 	port->port.drain_delay = 256;
+	priv->port = port;
 
 	return 0;
 }
-- 
1.9.1

[PATCH V9 05/10] USB: f81232: implement MCR/MSR function

[Peter Hung]

This patch implement relative MCR/MSR function, such like
tiocmget()/tiocmset()/dtr_rts()/carrier_raised()

original f81232_carrier_raised() compared with wrong value UART_DCD.
It's should compared with UART_MSR_DCD.

Signed-off-by: Peter Hung <hpeter+linux_kernel@gmail.com>
---
 drivers/usb/serial/f81232.c | 139 +++++++++++++++++++++++++++++++++++++-------
 1 file changed, 117 insertions(+), 22 deletions(-)

diff --git a/drivers/usb/serial/f81232.c b/drivers/usb/serial/f81232.c
index 1e1261f..28759a0 100644
--- a/drivers/usb/serial/f81232.c
+++ b/drivers/usb/serial/f81232.c
@@ -34,8 +34,10 @@ MODULE_DEVICE_TABLE(usb, id_table);
 /* USB Control EP parameter */
 #define F81232_REGISTER_REQUEST	0xa0
 #define F81232_GET_REGISTER		0xc0
+#define F81232_SET_REGISTER		0x40
 
 #define SERIAL_BASE_ADDRESS			0x0120
+#define MODEM_CONTROL_REGISTER		(0x04 + SERIAL_BASE_ADDRESS)
 #define MODEM_STATUS_REGISTER		(0x06 + SERIAL_BASE_ADDRESS)
 
 #define CONTROL_DTR			0x01
@@ -54,7 +56,7 @@ MODULE_DEVICE_TABLE(usb, id_table);
 
 struct f81232_private {
 	struct mutex lock;
-	u8 line_control;
+	u8 modem_control;
 	u8 modem_status;
 	struct work_struct interrupt_work;
 	struct usb_serial_port *port;
@@ -95,6 +97,42 @@ static int f81232_get_register(struct usb_serial_port *port, u16 reg, u8 *val)
 	return status;
 }
 
+static int f81232_set_register(struct usb_serial_port *port, u16 reg, u8 val)
+{
+	int status;
+	u8 *tmp;
+	struct usb_device *dev = port->serial->dev;
+
+	tmp = kmalloc(sizeof(val), GFP_KERNEL);
+	if (!tmp)
+		return -ENOMEM;
+
+	*tmp = val;
+
+	status = usb_control_msg(dev,
+				usb_sndctrlpipe(dev, 0),
+				F81232_REGISTER_REQUEST,
+				F81232_SET_REGISTER,
+				reg,
+				0,
+				tmp,
+				sizeof(val),
+				USB_CTRL_SET_TIMEOUT);
+	if (status != sizeof(val)) {
+		dev_err(&port->dev, "%s failed status: %d\n", __func__, status);
+
+		if (status < 0)
+			status = usb_translate_errors(status);
+		else
+			status = -EIO;
+	} else {
+		status = 0;
+	}
+
+	kfree(tmp);
+	return status;
+}
+
 static void f81232_read_msr(struct usb_serial_port *port)
 {
 	int status;
@@ -139,6 +177,51 @@ static void f81232_read_msr(struct usb_serial_port *port)
 	mutex_unlock(&priv->lock);
 }
 
+static int f81232_set_mctrl(struct usb_serial_port *port,
+					   unsigned int set, unsigned int clear)
+{
+	u8 val;
+	int status;
+	struct f81232_private *priv = usb_get_serial_port_data(port);
+
+	if (((set | clear) & (TIOCM_DTR | TIOCM_RTS)) == 0)
+		return 0;	/* no change */
+
+	/* 'set' takes precedence over 'clear' */
+	clear &= ~set;
+
+	/* force enable interrupt with OUT2 */
+	mutex_lock(&priv->lock);
+	val = UART_MCR_OUT2 | priv->modem_control;
+
+	if (clear & TIOCM_DTR)
+		val &= ~UART_MCR_DTR;
+
+	if (clear & TIOCM_RTS)
+		val &= ~UART_MCR_RTS;
+
+	if (set & TIOCM_DTR)
+		val |= UART_MCR_DTR;
+
+	if (set & TIOCM_RTS)
+		val |= UART_MCR_RTS;
+
+	dev_dbg(&port->dev, "%s new:%02x old:%02x\n", __func__,
+			val, priv->modem_control);
+
+	status = f81232_set_register(port, MODEM_CONTROL_REGISTER, val);
+	if (status) {
+		dev_err(&port->dev, "%s set MCR status < 0\n", __func__);
+		mutex_unlock(&priv->lock);
+		return status;
+	}
+
+	priv->modem_control = val;
+	mutex_unlock(&priv->lock);
+
+	return 0;
+}
+
 static void f81232_update_line_status(struct usb_serial_port *port,
 				      unsigned char *data,
 				      size_t actual_length)
@@ -254,12 +337,6 @@ static void f81232_process_read_urb(struct urb *urb)
 	tty_flip_buffer_push(&port->port);
 }
 
-static int set_control_lines(struct usb_device *dev, u8 value)
-{
-	/* FIXME - Stubbed out for now */
-	return 0;
-}
-
 static void f81232_break_ctl(struct tty_struct *tty, int break_state)
 {
 	/* FIXME - Stubbed out for now */
@@ -287,15 +364,35 @@ static void f81232_set_termios(struct tty_struct *tty,
 
 static int f81232_tiocmget(struct tty_struct *tty)
 {
-	/* FIXME - Stubbed out for now */
-	return 0;
+	int r;
+	struct usb_serial_port *port = tty->driver_data;
+	struct f81232_private *port_priv = usb_get_serial_port_data(port);
+	u8 mcr, msr;
+
+	/* force get current MSR changed state */
+	f81232_read_msr(port);
+
+	mutex_lock(&port_priv->lock);
+	mcr = port_priv->modem_control;
+	msr = port_priv->modem_status;
+	mutex_unlock(&port_priv->lock);
+
+	r = (mcr & UART_MCR_DTR ? TIOCM_DTR : 0) |
+		(mcr & UART_MCR_RTS ? TIOCM_RTS : 0) |
+		(msr & UART_MSR_CTS ? TIOCM_CTS : 0) |
+		(msr & UART_MSR_DCD ? TIOCM_CAR : 0) |
+		(msr & UART_MSR_RI ? TIOCM_RI : 0) |
+		(msr & UART_MSR_DSR ? TIOCM_DSR : 0);
+
+	return r;
 }
 
 static int f81232_tiocmset(struct tty_struct *tty,
 			unsigned int set, unsigned int clear)
 {
-	/* FIXME - Stubbed out for now */
-	return 0;
+	struct usb_serial_port *port = tty->driver_data;
+
+	return f81232_set_mctrl(port, set, clear);
 }
 
 static int f81232_open(struct tty_struct *tty, struct usb_serial_port *port)
@@ -330,24 +427,22 @@ static void f81232_close(struct usb_serial_port *port)
 
 static void f81232_dtr_rts(struct usb_serial_port *port, int on)
 {
-	struct f81232_private *priv = usb_get_serial_port_data(port);
-	u8 control;
-
-	mutex_lock(&priv->lock);
-	/* Change DTR and RTS */
 	if (on)
-		priv->line_control |= (CONTROL_DTR | CONTROL_RTS);
+		f81232_set_mctrl(port, TIOCM_DTR | TIOCM_RTS, 0);
 	else
-		priv->line_control &= ~(CONTROL_DTR | CONTROL_RTS);
-	control = priv->line_control;
-	mutex_unlock(&priv->lock);
-	set_control_lines(port->serial->dev, control);
+		f81232_set_mctrl(port, 0, TIOCM_DTR | TIOCM_RTS);
 }
 
 static int f81232_carrier_raised(struct usb_serial_port *port)
 {
+	u8 msr;
 	struct f81232_private *priv = usb_get_serial_port_data(port);
-	if (priv->modem_status & UART_DCD)
+
+	mutex_lock(&priv->lock);
+	msr = priv->modem_status;
+	mutex_unlock(&priv->lock);
+
+	if (msr & UART_MSR_DCD)
 		return 1;
 	return 0;
 }
-- 
1.9.1

[PATCH V9 06/10] USB: f81232: implement port enable/disable method

[Peter Hung]

We put FCR/IER initial step to f81232_port_enable()/f81232_port_disable().
When port is open, it set MSR interrupt on. Otherwise set it off.

Signed-off-by: Peter Hung <hpeter+linux_kernel@gmail.com>
---
 drivers/usb/serial/f81232.c | 49 +++++++++++++++++++++++++++++++++++++++++++++
 1 file changed, 49 insertions(+)

diff --git a/drivers/usb/serial/f81232.c b/drivers/usb/serial/f81232.c
index 28759a0..f0109a4 100644
--- a/drivers/usb/serial/f81232.c
+++ b/drivers/usb/serial/f81232.c
@@ -37,6 +37,8 @@ MODULE_DEVICE_TABLE(usb, id_table);
 #define F81232_SET_REGISTER		0x40
 
 #define SERIAL_BASE_ADDRESS			0x0120
+#define INTERRUPT_ENABLE_REGISTER	(0x01 + SERIAL_BASE_ADDRESS)
+#define FIFO_CONTROL_REGISTER		(0x02 + SERIAL_BASE_ADDRESS)
 #define MODEM_CONTROL_REGISTER		(0x04 + SERIAL_BASE_ADDRESS)
 #define MODEM_STATUS_REGISTER		(0x06 + SERIAL_BASE_ADDRESS)
 
@@ -348,6 +350,48 @@ static void f81232_break_ctl(struct tty_struct *tty, int break_state)
 	 */
 }
 
+static int f81232_port_enable(struct usb_serial_port *port)
+{
+	u8 val;
+	int status;
+
+	/* fifo on, trigger8, clear TX/RX*/
+	val = UART_FCR_TRIGGER_8 | UART_FCR_ENABLE_FIFO | UART_FCR_CLEAR_RCVR |
+			UART_FCR_CLEAR_XMIT;
+
+	status = f81232_set_register(port, FIFO_CONTROL_REGISTER, val);
+	if (status) {
+		dev_err(&port->dev, "%s failed to set FCR: %d\n",
+			__func__, status);
+		return status;
+	}
+
+	/* MSR Interrupt only, LSR will read from Bulk-in odd byte */
+	status = f81232_set_register(port, INTERRUPT_ENABLE_REGISTER,
+			UART_IER_MSI);
+	if (status) {
+		dev_err(&port->dev, "%s failed to set IER: %d\n",
+			__func__, status);
+		return status;
+	}
+
+	return 0;
+}
+
+static int f81232_port_disable(struct usb_serial_port *port)
+{
+	int status;
+
+	status = f81232_set_register(port, INTERRUPT_ENABLE_REGISTER, 0);
+	if (status) {
+		dev_err(&port->dev, "%s failed to set IER: %d\n",
+			__func__, status);
+		return status;
+	}
+
+	return 0;
+}
+
 static void f81232_set_termios(struct tty_struct *tty,
 		struct usb_serial_port *port, struct ktermios *old_termios)
 {
@@ -399,6 +443,10 @@ static int f81232_open(struct tty_struct *tty, struct usb_serial_port *port)
 {
 	int result;
 
+	result = f81232_port_enable(port);
+	if (result)
+		return result;
+
 	/* Setup termios */
 	if (tty)
 		f81232_set_termios(tty, port, NULL);
@@ -421,6 +469,7 @@ static int f81232_open(struct tty_struct *tty, struct usb_serial_port *port)
 
 static void f81232_close(struct usb_serial_port *port)
 {
+	f81232_port_disable(port);
 	usb_serial_generic_close(port);
 	usb_kill_urb(port->interrupt_in_urb);
 }
-- 
1.9.1

[PATCH V9 07/10] USB: f81232: implement set_termios()

[Peter Hung]

The original driver had do not any h/w change in driver.
This patch implements with configure H/W for
baud/parity/word length/stop bits functional in f81232_set_termios().

This patch also implement DTR/RTS control when baudrate B0.
We drop DTR/RTS when B0, otherwise enable it.

We are checking baudrate in set_termios() too, If baudrate larger then 115200,
it will be changed to 115200 and use tty_encode_baud_rate() to encode into tty

Signed-off-by: Peter Hung <hpeter+linux_kernel@gmail.com>
---
 drivers/usb/serial/f81232.c | 112 ++++++++++++++++++++++++++++++++++++++++++--
 1 file changed, 108 insertions(+), 4 deletions(-)

diff --git a/drivers/usb/serial/f81232.c b/drivers/usb/serial/f81232.c
index f0109a4..6be37f3 100644
--- a/drivers/usb/serial/f81232.c
+++ b/drivers/usb/serial/f81232.c
@@ -31,14 +31,19 @@ static const struct usb_device_id id_table[] = {
 };
 MODULE_DEVICE_TABLE(usb, id_table);
 
+/* Maximum baudrate for F81232 */
+#define F81232_MAX_BAUDRATE	115200
+
 /* USB Control EP parameter */
 #define F81232_REGISTER_REQUEST	0xa0
 #define F81232_GET_REGISTER		0xc0
 #define F81232_SET_REGISTER		0x40
 
 #define SERIAL_BASE_ADDRESS			0x0120
+#define RECEIVE_BUFFER_REGISTER		(0x00 + SERIAL_BASE_ADDRESS)
 #define INTERRUPT_ENABLE_REGISTER	(0x01 + SERIAL_BASE_ADDRESS)
 #define FIFO_CONTROL_REGISTER		(0x02 + SERIAL_BASE_ADDRESS)
+#define LINE_CONTROL_REGISTER		(0x03 + SERIAL_BASE_ADDRESS)
 #define MODEM_CONTROL_REGISTER		(0x04 + SERIAL_BASE_ADDRESS)
 #define MODEM_STATUS_REGISTER		(0x06 + SERIAL_BASE_ADDRESS)
 
@@ -64,6 +69,11 @@ struct f81232_private {
 	struct usb_serial_port *port;
 };
 
+static int calc_baud_divisor(speed_t baudrate)
+{
+	return DIV_ROUND_CLOSEST(F81232_MAX_BAUDRATE, baudrate);
+}
+
 static int f81232_get_register(struct usb_serial_port *port, u16 reg, u8 *val)
 {
 	int status;
@@ -350,6 +360,53 @@ static void f81232_break_ctl(struct tty_struct *tty, int break_state)
 	 */
 }
 
+static void f81232_set_baudrate(struct usb_serial_port *port, speed_t baudrate)
+{
+	u8 lcr;
+	int divisor, status = 0;
+
+	divisor = calc_baud_divisor(baudrate);
+
+	status = f81232_get_register(port, LINE_CONTROL_REGISTER,
+			 &lcr); /* get LCR */
+	if (status) {
+		dev_err(&port->dev, "%s failed to get LCR: %d\n",
+			__func__, status);
+		return;
+	}
+
+	status = f81232_set_register(port, LINE_CONTROL_REGISTER,
+			 lcr | UART_LCR_DLAB); /* Enable DLAB */
+	if (status) {
+		dev_err(&port->dev, "%s failed to set DLAB: %d\n",
+			__func__, status);
+		return;
+	}
+
+	status = f81232_set_register(port, RECEIVE_BUFFER_REGISTER,
+			 divisor & 0x00ff); /* low */
+	if (status) {
+		dev_err(&port->dev, "%s failed to set baudrate MSB: %d\n",
+			__func__, status);
+		goto reapply_lcr;
+	}
+
+	status = f81232_set_register(port, INTERRUPT_ENABLE_REGISTER,
+			 (divisor & 0xff00) >> 8); /* high */
+	if (status) {
+		dev_err(&port->dev, "%s failed to set baudrate LSB: %d\n",
+			__func__, status);
+	}
+
+reapply_lcr:
+	status = f81232_set_register(port, LINE_CONTROL_REGISTER,
+			lcr & ~UART_LCR_DLAB);
+	if (status) {
+		dev_err(&port->dev, "%s failed to set DLAB: %d\n",
+			__func__, status);
+	}
+}
+
 static int f81232_port_enable(struct usb_serial_port *port)
 {
 	u8 val;
@@ -395,15 +452,62 @@ static int f81232_port_disable(struct usb_serial_port *port)
 static void f81232_set_termios(struct tty_struct *tty,
 		struct usb_serial_port *port, struct ktermios *old_termios)
 {
-	/* FIXME - Stubbed out for now */
+	u8 new_lcr = 0;
+	int status = 0;
+	speed_t baudrate;
 
 	/* Don't change anything if nothing has changed */
 	if (old_termios && !tty_termios_hw_change(&tty->termios, old_termios))
 		return;
 
-	/* Do the real work here... */
-	if (old_termios)
-		tty_termios_copy_hw(&tty->termios, old_termios);
+	if (C_BAUD(tty) == B0)
+		f81232_set_mctrl(port, 0, TIOCM_DTR | TIOCM_RTS);
+	else if (old_termios && (old_termios->c_cflag & CBAUD) == B0)
+		f81232_set_mctrl(port, TIOCM_DTR | TIOCM_RTS, 0);
+
+	baudrate = tty_get_baud_rate(tty);
+	if (baudrate > 0) {
+		if (baudrate > F81232_MAX_BAUDRATE) {
+			baudrate = F81232_MAX_BAUDRATE;
+			tty_encode_baud_rate(tty, baudrate, baudrate);
+		}
+		f81232_set_baudrate(port, baudrate);
+	}
+
+	if (C_PARENB(tty)) {
+		new_lcr |= UART_LCR_PARITY;
+
+		if (!C_PARODD(tty))
+			new_lcr |= UART_LCR_EPAR;
+
+		if (C_CMSPAR(tty))
+			new_lcr |= UART_LCR_SPAR;
+	}
+
+	if (C_CSTOPB(tty))
+		new_lcr |= UART_LCR_STOP;
+
+	switch (C_CSIZE(tty)) {
+	case CS5:
+		new_lcr |= UART_LCR_WLEN5;
+		break;
+	case CS6:
+		new_lcr |= UART_LCR_WLEN6;
+		break;
+	case CS7:
+		new_lcr |= UART_LCR_WLEN7;
+		break;
+	default:
+	case CS8:
+		new_lcr |= UART_LCR_WLEN8;
+		break;
+	}
+
+	status = f81232_set_register(port, LINE_CONTROL_REGISTER, new_lcr);
+	if (status) {
+		dev_err(&port->dev, "%s failed to set LCR: %d\n",
+			__func__, status);
+	}
 }
 
 static int f81232_tiocmget(struct tty_struct *tty)
-- 
1.9.1

[PATCH V9 08/10] USB: f81232: clarify f81232_ioctl() and fix

[Peter Hung]

We extract TIOCGSERIAL section in f81232_ioctl() to f81232_get_serial_info()
to make it clarify.

Also we fix device type from 16654 to 16550A, and set it's baud_base
to 115200 (1.8432MHz/16).

Signed-off-by: Peter Hung <hpeter+linux_kernel@gmail.com>
---
 drivers/usb/serial/f81232.c | 30 +++++++++++++++++++-----------
 1 file changed, 19 insertions(+), 11 deletions(-)

diff --git a/drivers/usb/serial/f81232.c b/drivers/usb/serial/f81232.c
index 6be37f3..0da16ce 100644
--- a/drivers/usb/serial/f81232.c
+++ b/drivers/usb/serial/f81232.c
@@ -600,24 +600,32 @@ static int f81232_carrier_raised(struct usb_serial_port *port)
 	return 0;
 }
 
+static int f81232_get_serial_info(struct usb_serial_port *port,
+		unsigned long arg)
+{
+	struct serial_struct ser;
+
+	memset(&ser, 0, sizeof(ser));
+
+	ser.type = PORT_16550A;
+	ser.line = port->minor;
+	ser.port = port->port_number;
+	ser.baud_base = F81232_MAX_BAUDRATE;
+
+	if (copy_to_user((void __user *)arg, &ser, sizeof(ser)))
+		return -EFAULT;
+
+	return 0;
+}
+
 static int f81232_ioctl(struct tty_struct *tty,
 			unsigned int cmd, unsigned long arg)
 {
-	struct serial_struct ser;
 	struct usb_serial_port *port = tty->driver_data;
 
 	switch (cmd) {
 	case TIOCGSERIAL:
-		memset(&ser, 0, sizeof ser);
-		ser.type = PORT_16654;
-		ser.line = port->minor;
-		ser.port = port->port_number;
-		ser.baud_base = 460800;
-
-		if (copy_to_user((void __user *)arg, &ser, sizeof ser))
-			return -EFAULT;
-
-		return 0;
+		return f81232_get_serial_info(port, arg);
 	default:
 		break;
 	}
-- 
1.9.1

[PATCH V9 09/10] USB: f81232: cleanup non-used define

[Peter Hung]

We remove non-used define in this patch to avoid wrong usage.

Signed-off-by: Peter Hung <hpeter+linux_kernel@gmail.com>
---
 drivers/usb/serial/f81232.c | 14 --------------
 1 file changed, 14 deletions(-)

diff --git a/drivers/usb/serial/f81232.c b/drivers/usb/serial/f81232.c
index 0da16ce..a0e0b9d 100644
--- a/drivers/usb/serial/f81232.c
+++ b/drivers/usb/serial/f81232.c
@@ -47,20 +47,6 @@ MODULE_DEVICE_TABLE(usb, id_table);
 #define MODEM_CONTROL_REGISTER		(0x04 + SERIAL_BASE_ADDRESS)
 #define MODEM_STATUS_REGISTER		(0x06 + SERIAL_BASE_ADDRESS)
 
-#define CONTROL_DTR			0x01
-#define CONTROL_RTS			0x02
-
-#define UART_STATE			0x08
-#define UART_STATE_TRANSIENT_MASK	0x74
-#define UART_DCD			0x01
-#define UART_DSR			0x02
-#define UART_BREAK_ERROR		0x04
-#define UART_RING			0x08
-#define UART_FRAME_ERROR		0x10
-#define UART_PARITY_ERROR		0x20
-#define UART_OVERRUN_ERROR		0x40
-#define UART_CTS			0x80
-
 struct f81232_private {
 	struct mutex lock;
 	u8 modem_control;
-- 
1.9.1

[PATCH V9 10/10] USB: f81232: modify/add author

[Peter Hung]

Add me to co-author and fix no '>' in greg kh's email

Signed-off-by: Peter Hung <hpeter+linux_kernel@gmail.com>
---
 drivers/usb/serial/f81232.c | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

diff --git a/drivers/usb/serial/f81232.c b/drivers/usb/serial/f81232.c
index a0e0b9d..54cc707 100644
--- a/drivers/usb/serial/f81232.c
+++ b/drivers/usb/serial/f81232.c
@@ -688,5 +688,6 @@ static struct usb_serial_driver * const serial_drivers[] = {
 module_usb_serial_driver(serial_drivers, id_table);
 
 MODULE_DESCRIPTION("Fintek F81232 USB to serial adaptor driver");
-MODULE_AUTHOR("Greg Kroah-Hartman <gregkh@linuxfoundation.org");
+MODULE_AUTHOR("Greg Kroah-Hartman <gregkh@linuxfoundation.org>");
+MODULE_AUTHOR("Peter Hong <peter_hong@fintek.com.tw>");
 MODULE_LICENSE("GPL v2");
-- 
1.9.1