[PATCH v3 10/10] dt-bindings: msm/hdmi: Add HDMI PHY bindings

[Archit Taneja <architt@codeaurora.org>]

Add HDMI PHY bindings. Update the example to use HDMI PHY.

Added a missing power-domains property in the HDMI core bindings. Also,
simplified HDMI TX's DT node name in the example.

Cc: devicetree@vger.kernel.org
Cc: Rob Herring <robh@kernel.org>

Signed-off-by: Archit Taneja <architt@codeaurora.org>
---
 .../devicetree/bindings/display/msm/hdmi.txt       | 46 +++++++++++++++++++++-
 1 file changed, 44 insertions(+), 2 deletions(-)

diff --git a/Documentation/devicetree/bindings/display/msm/hdmi.txt b/Documentation/devicetree/bindings/display/msm/hdmi.txt
index 379ee2e..b63f614 100644
--- a/Documentation/devicetree/bindings/display/msm/hdmi.txt
+++ b/Documentation/devicetree/bindings/display/msm/hdmi.txt
@@ -11,6 +11,7 @@ Required properties:
 - reg: Physical base address and length of the controller's registers
 - reg-names: "core_physical"
 - interrupts: The interrupt signal from the hdmi block.
+- power-domains: Should be <&mmcc MDSS_GDSC>.
 - clocks: device clocks
   See ../clocks/clock-bindings.txt for details.
 - qcom,hdmi-tx-ddc-clk-gpio: ddc clk pin
@@ -18,6 +19,8 @@ Required properties:
 - qcom,hdmi-tx-hpd-gpio: hpd pin
 - core-vdda-supply: phandle to supply regulator
 - hdmi-mux-supply: phandle to mux regulator
+- phys: the phandle for the HDMI PHY device
+- phy-names: the name of the corresponding PHY device
 
 Optional properties:
 - qcom,hdmi-tx-mux-en-gpio: hdmi mux enable pin
@@ -27,15 +30,38 @@ Optional properties:
 - pinctrl-0: the default pinctrl state (active)
 - pinctrl-1: the "sleep" pinctrl state
 
+HDMI PHY:
+Required properties:
+- compatible: Could be the following
+  * "qcom,hdmi-phy-8660"
+  * "qcom,hdmi-phy-8960"
+  * "qcom,hdmi-phy-8974"
+  * "qcom,hdmi-phy-8084"
+  * "qcom,hdmi-phy-8996"
+- #phy-cells: Number of cells in a PHY specifier; Should be 0.
+- reg: Physical base address and length of the registers of the PHY sub blocks.
+- reg-names: The names of register regions. The following regions are required:
+  * "hdmi_phy"
+  * "hdmi_pll"
+  For HDMI PHY on msm8996, these additional register regions are required:
+    * "hdmi_tx_l0"
+    * "hdmi_tx_l1"
+    * "hdmi_tx_l3"
+    * "hdmi_tx_l4"
+- power-domains: Should be <&mmcc MDSS_GDSC>.
+- clocks: device clocks
+  See Documentation/devicetree/bindings/clocks/clock-bindings.txt for details.
+- core-vdda-supply: phandle to vdda regulator device node
+
 Example:
 
 / {
 	...
 
-	hdmi: qcom,hdmi-tx-8960@4a00000 {
+	hdmi: hdmi@4a00000 {
 		compatible = "qcom,hdmi-tx-8960";
 		reg-names = "core_physical";
-		reg = <0x04a00000 0x1000>;
+		reg = <0x04a00000 0x2f0>;
 		interrupts = <GIC_SPI 79 0>;
 		power-domains = <&mmcc MDSS_GDSC>;
 		clock-names =
@@ -54,5 +80,21 @@ Example:
 		pinctrl-names = "default", "sleep";
 		pinctrl-0 = <&hpd_active  &ddc_active  &cec_active>;
 		pinctrl-1 = <&hpd_suspend &ddc_suspend &cec_suspend>;
+
+		phys = <&hdmi_phy>;
+		phy-names = "hdmi_phy";
+	};
+
+	hdmi_phy: phy@4a00400 {
+		compatible = "qcom,hdmi-phy-8960";
+		reg-names = "hdmi_phy",
+			    "hdmi_pll";
+		reg = <0x4a00400 0x60>,
+		      <0x4a00500 0x100>;
+		#phy-cells = <0>;
+		power-domains = <&mmcc MDSS_GDSC>;
+		clock-names = "slave_iface_clk";
+		clocks = <&mmcc HDMI_S_AHB_CLK>;
+		core-vdda-supply = <&pm8921_hdmi_mvs>;
 	};
 };
-- 
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
hosted by The Linux Foundation

_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel