From: Xavier Bestel <xavier.bestel@free.fr>
To: linux-wireless@vger.kernel.org
Subject: Can't authenticate to WPA network with rt2800usb driver
Date: Wed, 04 Jan 2017 11:37:50 +0100 [thread overview]
Message-ID: <1483526270.8560.70.camel@free.fr> (raw)
Hi,
I have this USB WiFi dongle:
[2921541.271677] usb 3-12.6: new high-speed USB device number 65 using xhci_hcd
[2921541.393139] usb 3-12.6: New USB device found, idVendor=148f, idProduct=5370
[2921541.393141] usb 3-12.6: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[2921541.393142] usb 3-12.6: Product: 802.11 n WLAN
[2921541.393142] usb 3-12.6: Manufacturer: Ralink
[2921541.393143] usb 3-12.6: SerialNumber: 1.0
[2921541.471914] usb 3-12.6: reset high-speed USB device number 65 using xhci_hcd
[2921541.586974] ieee80211 phy4: rt2x00_set_rt: Info - RT chipset 5390, rev 0502 detected
[2921541.596791] ieee80211 phy4: rt2x00_set_rf: Info - RF chipset 5370 detected
[2921541.597005] ieee80211 phy4: Selected rate control algorithm 'minstrel_ht'
[2921541.806292] rt2800usb 3-12.6:1.0 wlx7cdd90463ef8: renamed from wlan0
[2921541.979061] IPv6: ADDRCONF(NETDEV_UP): wlx7cdd90463ef8: link is not ready
[2921541.979088] ieee80211 phy4: rt2x00lib_request_firmware: Info - Loading firmware file 'rt2870.bin'
[2921542.027030] rt2800usb 3-12.6:1.0: firmware: direct-loading firmware rt2870.bin
[2921542.027035] ieee80211 phy4: rt2x00lib_request_firmware: Info - Firmware detected - version: 0.36
It's inserted into a debian jessie box, kernel 4.8.0-1-amd64.
The box refuses to connect to a WPA AP (although it connects fine with
a PCI WiFi card):
Jan 4 11:22:29 pcxav NetworkManager[15150]: <info> [1483525349.1350] device (wlx7cdd90463ef8): Activation: starting connection 'MySecretSSID 2' (e6482e2d-adbc-4529-bafc-24c3e54f07e6)
Jan 4 11:22:29 pcxav NetworkManager[15150]: <info> [1483525349.1351] audit: op="connection-activate" uuid="e6482e2d-adbc-4529-bafc-24c3e54f07e6" name="MySecretSSID 2" pid=1599 uid=1000 result="success"
Jan 4 11:22:29 pcxav NetworkManager[15150]: <info> [1483525349.1352] device (wlx7cdd90463ef8): state change: disconnected -> prepare (reason 'none') [30 40 0]
Jan 4 11:22:29 pcxav NetworkManager[15150]: <info> [1483525349.1445] device (wlx7cdd90463ef8): set-hw-addr: set-cloned MAC address to 7C:DD:90:46:3E:F8 (permanent)
Jan 4 11:22:29 pcxav kernel: [2921135.939166] IPv6: ADDRCONF(NETDEV_UP): wlx7cdd90463ef8: link is not ready
Jan 4 11:22:29 pcxav NetworkManager[15150]: <info> [1483525349.3266] device (wlx7cdd90463ef8): state change: prepare -> config (reason 'none') [40 50 0]
Jan 4 11:22:29 pcxav NetworkManager[15150]: <info> [1483525349.3267] device (wlx7cdd90463ef8): Activation: (wifi) access point 'MySecretSSID 2' has security, but secrets are required.
Jan 4 11:22:29 pcxav NetworkManager[15150]: <info> [1483525349.3267] device (wlx7cdd90463ef8): state change: config -> need-auth (reason 'none') [50 60 0]
Jan 4 11:22:29 pcxav NetworkManager[15150]: <info> [1483525349.3287] device (wlx7cdd90463ef8): state change: need-auth -> prepare (reason 'none') [60 40 0]
Jan 4 11:22:29 pcxav NetworkManager[15150]: <info> [1483525349.3289] device (wlx7cdd90463ef8): state change: prepare -> config (reason 'none') [40 50 0]
Jan 4 11:22:29 pcxav NetworkManager[15150]: <info> [1483525349.3290] device (wlx7cdd90463ef8): Activation: (wifi) connection 'MySecretSSID 2' has security, and secrets exist. No new secrets needed.
Jan 4 11:22:29 pcxav NetworkManager[15150]: <info> [1483525349.3291] Config: added 'ssid' value 'MySecretSSID'
Jan 4 11:22:29 pcxav NetworkManager[15150]: <info> [1483525349.3291] Config: added 'scan_ssid' value '1'
Jan 4 11:22:29 pcxav NetworkManager[15150]: <info> [1483525349.3291] Config: added 'key_mgmt' value 'WPA-PSK'
Jan 4 11:22:29 pcxav NetworkManager[15150]: <info> [1483525349.3291] Config: added 'auth_alg' value 'OPEN'
Jan 4 11:22:29 pcxav NetworkManager[15150]: <info> [1483525349.3291] Config: added 'psk' value '<omitted>'
Jan 4 11:22:29 pcxav NetworkManager[15150]: <info> [1483525349.3529] sup-iface[0x55f2087344e0,wlx7cdd90463ef8] config: set interface ap_scan to 1
Jan 4 11:22:29 pcxav wpa_supplicant[13666]: wlx7cdd90463ef8: SME: Trying to authenticate with 5c:33:8e:56:78:d3 (SSID='MySecretSSID' freq=2437 MHz)
Jan 4 11:22:29 pcxav kernel: [2921135.972360] wlx7cdd90463ef8: authenticate with 5c:33:8e:56:78:d3
Jan 4 11:22:29 pcxav NetworkManager[15150]: <info> [1483525349.3774] device (wlx7cdd90463ef8): supplicant interface state: inactive -> authenticating
Jan 4 11:22:29 pcxav kernel: [2921135.990588] wlx7cdd90463ef8: send auth to 5c:33:8e:56:78:d3 (try 1/3)
Jan 4 11:22:29 pcxav kernel: [2921135.999983] wlx7cdd90463ef8: authenticated
Jan 4 11:22:34 pcxav kernel: [2921140.991625] wlx7cdd90463ef8: aborting authentication with 5c:33:8e:56:78:d3 by local choice (Reason: 3=DEAUTH_LEAVING)
Jan 4 11:22:34 pcxav wpa_supplicant[13666]: wlx7cdd90463ef8: CTRL-EVENT-SSID-TEMP-DISABLED id=1 ssid="MySecretSSID" auth_failures=1 duration=10 reason=CONN_FAILED
Jan 4 11:22:34 pcxav NetworkManager[15150]: <info> [1483525354.4250] device (wlx7cdd90463ef8): supplicant interface state: authenticating -> disconnected
Jan 4 11:22:44 pcxav NetworkManager[15150]: <info> [1483525364.4264] device (wlx7cdd90463ef8): supplicant interface state: disconnected -> scanning
Jan 4 11:22:45 pcxav wpa_supplicant[13666]: wlx7cdd90463ef8: CTRL-EVENT-SSID-REENABLED id=1 ssid="MySecretSSID"
Jan 4 11:22:45 pcxav wpa_supplicant[13666]: wlx7cdd90463ef8: SME: Trying to authenticate with 5c:33:8e:56:78:d3 (SSID='MySecretSSID' freq=2437 MHz)
Jan 4 11:22:45 pcxav kernel: [2921152.045396] wlx7cdd90463ef8: authenticate with 5c:33:8e:56:78:d3
Jan 4 11:22:45 pcxav NetworkManager[15150]: <info> [1483525365.4655] device (wlx7cdd90463ef8): supplicant interface state: scanning -> authenticating
Jan 4 11:22:45 pcxav kernel: [2921152.079166] wlx7cdd90463ef8: send auth to 5c:33:8e:56:78:d3 (try 1/3)
Jan 4 11:22:45 pcxav kernel: [2921152.081749] wlx7cdd90463ef8: authenticated
Jan 4 11:22:50 pcxav kernel: [2921157.080963] wlx7cdd90463ef8: aborting authentication with 5c:33:8e:56:78:d3 by local choice (Reason: 3=DEAUTH_LEAVING)
Jan 4 11:22:50 pcxav wpa_supplicant[13666]: wlx7cdd90463ef8: CTRL-EVENT-SSID-TEMP-DISABLED id=1 ssid="MySecretSSID" auth_failures=2 duration=20 reason=CONN_FAILED
Jan 4 11:22:50 pcxav NetworkManager[15150]: <info> [1483525370.5091] device (wlx7cdd90463ef8): supplicant interface state: authenticating -> disconnected
Jan 4 11:22:54 pcxav NetworkManager[15150]: <warn> [1483525374.7275] device (wlx7cdd90463ef8): Activation: (wifi) association took too long, failing activation
Jan 4 11:22:54 pcxav NetworkManager[15150]: <info> [1483525374.7275] device (wlx7cdd90463ef8): state change: config -> failed (reason 'ssid-not-found') [50 120 53]
Jan 4 11:22:54 pcxav NetworkManager[15150]: <warn> [1483525374.7279] device (wlx7cdd90463ef8): Activation: failed for connection 'MySecretSSID 2'
Jan 4 11:22:54 pcxav NetworkManager[15150]: <info> [1483525374.7282] device (wlx7cdd90463ef8): state change: failed -> disconnected (reason 'none') [120 30 0]
Jan 4 11:22:54 pcxav kernel: [2921161.343145] IPv6: ADDRCONF(NETDEV_UP): wlx7cdd90463ef8: link is not ready
Jan 4 11:22:54 pcxav NetworkManager[15150]: <info> [1483525374.7454] device (wlx7cdd90463ef8): set-hw-addr: set MAC address to EA:EC:7C:7D:D6:86 (scanning)
Jan 4 11:22:54 pcxav kernel: [2921161.536075] IPv6: ADDRCONF(NETDEV_UP): wlx7cdd90463ef8: link is not ready
Jan 4 11:22:55 pcxav NetworkManager[15150]: <info> [1483525375.9561] device (wlx7cdd90463ef8): supplicant interface state: disconnected -> inactive
Does anyone have a hint to make it work ?
Regards,
Xav
next reply other threads:[~2017-01-04 10:39 UTC|newest]
Thread overview: 4+ messages / expand[flat|nested] mbox.gz Atom feed top
2017-01-04 10:37 Xavier Bestel [this message]
2017-01-04 15:02 ` Can't authenticate to WPA network with rt2800usb driver Stanislaw Gruszka
2017-01-04 16:02 ` Xavier Bestel
2017-01-05 10:56 ` Stanislaw Gruszka
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1483526270.8560.70.camel@free.fr \
--to=xavier.bestel@free.fr \
--cc=linux-wireless@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.