From: "Benjamin Monate <Benjamin Monate" <Benjamin.Monate@lri.fr>
To: linux-kernel@vger.kernel.org
Subject: Re: Strange lockup of the timer with 2.4.0-test10 SMP (and older)
Date: Wed, 22 Nov 2000 10:45:18 +0100 (MET) [thread overview]
Message-ID: <14875.38318.5084.502248@sun-demons> (raw)
In-Reply-To: <Pine.GSO.3.96.1001121175618.28403A-100000@delta.ds2.pg.gda.pl>
In-Reply-To: <14874.41589.359267.717984@sun-demons> <Pine.GSO.3.96.1001121175618.28403A-100000@delta.ds2.pg.gda.pl>
Dans son message du Tue 21 November, Maciej W. Rozycki ecrit :
> But this message is printed when a workaround for certain early SMP EISA
> boards gets activated. You shouldn't normally get it for anything newer
> than P5/66 unless your MP-table is broken. Can you send me a dump of your
> MP-table (just issue `dmesg -s 32768' after a bootstrap -- the table is at
> the top).
Ok: here is the begining of dmesg.
Linux version 2.4.0-test10 (root@pc8-118) (gcc version 2.95.2 20000220 (Debian GNU/Linux)) #1 SMP Thu Nov 16 13:18:57 CET 2000
BIOS-provided physical RAM map:
BIOS-e820: 000000000009f000 @ 0000000000000000 (usable)
BIOS-e820: 0000000000001000 @ 000000000009f000 (reserved)
BIOS-e820: 0000000000010000 @ 00000000000f0000 (reserved)
BIOS-e820: 000000007fefb000 @ 0000000000100000 (usable)
BIOS-e820: 0000000000004000 @ 000000007fffb000 (ACPI data)
BIOS-e820: 0000000000001000 @ 000000007ffff000 (ACPI NVS)
BIOS-e820: 0000000000010000 @ 00000000fec00000 (reserved)
BIOS-e820: 0000000000001000 @ 00000000fee00000 (reserved)
BIOS-e820: 0000000000080000 @ 00000000fff80000 (reserved)
1151MB HIGHMEM available.
Scan SMP from c0000000 for 1024 bytes.
Scan SMP from c009fc00 for 1024 bytes.
Scan SMP from c00f0000 for 65536 bytes.
found SMP MP-table at 000f5270
hm, page 000f5000 reserved twice.
hm, page 000f6000 reserved twice.
hm, page 000f4000 reserved twice.
hm, page 000f5000 reserved twice.
On node 0 totalpages: 524283
zone(0): 4096 pages.
zone(1): 225280 pages.
zone(2): 294907 pages.
Intel MultiProcessor Specification v1.4
Virtual Wire compatibility mode.
OEM ID: OEM00000 Product ID: PROD00000000 APIC at: 0xFEE00000
Processor #3 Pentium(tm) Pro APIC version 17
Floating point unit present.
Machine Exception supported.
64 bit compare & exchange supported.
Internal APIC present.
Bootup CPU
Processor #0 Pentium(tm) Pro APIC version 17
Floating point unit present.
Machine Exception supported.
64 bit compare & exchange supported.
Internal APIC present.
Bus #0 is PCI
Bus #1 is PCI
Bus #2 is ISA
I/O APIC #2 Version 17 at 0xFEC00000.
I/O APIC #3 Version 17 at 0xFEC01000.
Int: type 3, pol 0, trig 0, bus 2, IRQ 00, APIC ID 2, APIC INT 00
Int: type 0, pol 0, trig 0, bus 2, IRQ 01, APIC ID 2, APIC INT 01
Int: type 0, pol 0, trig 0, bus 2, IRQ 00, APIC ID 2, APIC INT 02
Int: type 0, pol 0, trig 0, bus 2, IRQ 03, APIC ID 2, APIC INT 03
Int: type 0, pol 0, trig 0, bus 2, IRQ 04, APIC ID 2, APIC INT 04
Int: type 0, pol 0, trig 0, bus 2, IRQ 06, APIC ID 2, APIC INT 06
Int: type 0, pol 0, trig 0, bus 2, IRQ 07, APIC ID 2, APIC INT 07
Int: type 0, pol 0, trig 0, bus 2, IRQ 08, APIC ID 2, APIC INT 08
Int: type 0, pol 0, trig 0, bus 2, IRQ 0c, APIC ID 2, APIC INT 0c
Int: type 0, pol 3, trig 3, bus 0, IRQ 08, APIC ID 3, APIC INT 04
Int: type 0, pol 3, trig 3, bus 0, IRQ 0c, APIC ID 3, APIC INT 00
Int: type 0, pol 3, trig 3, bus 0, IRQ 10, APIC ID 3, APIC INT 01
Int: type 0, pol 3, trig 3, bus 2, IRQ 09, APIC ID 2, APIC INT 09
Int: type 0, pol 3, trig 3, bus 1, IRQ 14, APIC ID 3, APIC INT 08
Int: type 0, pol 3, trig 3, bus 1, IRQ 15, APIC ID 3, APIC INT 09
Lint: type 3, pol 1, trig 1, bus 2, IRQ 00, APIC ID ff, APIC LINT 00
Lint: type 1, pol 1, trig 1, bus 2, IRQ 00, APIC ID ff, APIC LINT 01
Processors: 2
mapped APIC to ffffe000 (fee00000)
mapped IOAPIC to ffffd000 (fec00000)
mapped IOAPIC to ffffc000 (fec01000)
Kernel command line: BOOT_IMAGE=new ro root=803 BOOT_FILE=/boot/vmlinuz-2.4.0-test2 nmi_watchdog=1
Initializing CPU#0
Detected 933.446 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 1861.22 BogoMIPS
Memory: 2059660k/2097132k available (1537k kernel code, 37084k reserved, 89k data, 200k init, 1179628k highmem)
Dentry-cache hash table entries: 262144 (order: 9, 2097152 bytes)
Buffer-cache hash table entries: 131072 (order: 7, 524288 bytes)
Page-cache hash table entries: 524288 (order: 9, 2097152 bytes)
Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.36 (20000221) Richard Gooch (rgooch@atnf.csiro.au)
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU0: Intel Pentium III (Coppermine) stepping 03
per-CPU timeslice cutoff: 731.32 usecs.
Getting VERSION: 40011
Getting VERSION: 40011
Getting ID: 3000000
Getting ID: c000000
Getting LVT0: 8700
Getting LVT1: 400
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
CPU present map: 9
Booting processor 1/0 eip 2000
Setting warm reset code and vector.
1.
2.
3.
Asserting INIT.
Waiting for send to finish...
+Deasserting INIT.
Waiting for send to finish...
+#startup loops: 2.
Sending STARTUP #1.
After apic_write.
Startup point 1.
Waiting for send to finish...
+Initializing CPU#1
CPU#1 (phys ID: 0) waiting for CALLOUT
Sending STARTUP #2.
After apic_write.
Startup point 1.
Waiting for send to finish...
+After Startup.
Before Callout 1.
After Callout 1.
CALLIN, before setup_local_APIC().
masked ExtINT on CPU#1
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Calibrating delay loop... 1861.22 BogoMIPS
Stack at about c322bfbc
Intel machine check reporting enabled on CPU#1.
OK.
CPU1: Intel Pentium III (Coppermine) stepping 03
CPU has booted.
Before bogomips.
Total of 2 processors activated (3722.44 BogoMIPS).
Before bogocount - setting activated=1.
Boot done.
ENABLING IO-APIC IRQs
...changing IO-APIC physical APIC ID to 2 ... ok.
BIOS bug, IO-APIC#1 ID 3 is already used!...
... fixing up to 1. (tell your hw vendor)
...changing IO-APIC physical APIC ID to 1 ... ok.
Synchronizing Arb IDs.
init IO_APIC IRQs
IO-APIC (apicid-pin) 2-0, 2-5, 2-10, 2-11, 2-13, 2-14, 2-15, 1-2, 1-3, 1-5, 1-6, 1-7, 1-10, 1-11, 1-12, 1-13, 1-14, 1-15 not connected.
..TIMER: vector=49 pin1=2 pin2=0
..MP-BIOS bug: 8254 timer not connected to IO-APIC
...trying to set up timer (IRQ0) through the 8259A ...
..... (found pin 0) ...works.
activating NMI Watchdog ... done.
number of MP IRQ sources: 15.
number of IO-APIC #2 registers: 16.
number of IO-APIC #1 registers: 16.
testing the IO APIC.......................
IO APIC #2......
.... register #00: 02000000
....... : physical APIC id: 02
.... register #01: 000F0011
....... : max redirection entries: 000F
....... : IO APIC version: 0011
.... register #02: 00000000
....... : arbitration: 00
.... IRQ redirection table:
NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
00 003 03 0 0 0 0 0 1 1 31
01 003 03 0 0 0 0 0 1 1 39
02 000 00 1 0 0 0 0 0 0 00
03 003 03 0 0 0 0 0 1 1 41
04 003 03 0 0 0 0 0 1 1 49
05 000 00 1 0 0 0 0 0 0 00
06 003 03 0 0 0 0 0 1 1 51
07 003 03 0 0 0 0 0 1 1 59
08 003 03 0 0 0 0 0 1 1 61
09 003 03 1 1 0 1 0 1 1 69
0a 000 00 1 0 0 0 0 0 0 00
0b 000 00 1 0 0 0 0 0 0 00
0c 003 03 0 0 0 0 0 1 1 71
0d 000 00 1 0 0 0 0 0 0 00
0e 000 00 1 0 0 0 0 0 0 00
0f 000 00 1 0 0 0 0 0 0 00
IO APIC #1......
.... register #00: 01000000
....... : physical APIC id: 01
.... register #01: 000F0011
....... : max redirection entries: 000F
....... : IO APIC version: 0011
.... register #02: 03000000
....... : arbitration: 03
.... IRQ redirection table:
NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
00 003 03 1 1 0 1 0 1 1 79
01 003 03 1 1 0 1 0 1 1 81
02 000 00 1 0 0 0 0 0 0 00
03 000 00 1 0 0 0 0 0 0 00
04 003 03 1 1 0 1 0 1 1 89
05 000 00 1 0 0 0 0 0 0 00
06 000 00 1 0 0 0 0 0 0 00
07 000 00 1 0 0 0 0 0 0 00
08 003 03 1 1 0 1 0 1 1 91
09 003 03 1 1 0 1 0 1 1 99
0a 000 00 1 0 0 0 0 0 0 00
0b 000 00 1 0 0 0 0 0 0 00
0c 000 00 1 0 0 0 0 0 0 00
0d 000 00 1 0 0 0 0 0 0 00
0e 000 00 1 0 0 0 0 0 0 00
0f 000 00 1 0 0 0 0 0 0 00
IRQ to pin mappings:
IRQ0 -> 2
IRQ1 -> 1
IRQ3 -> 3
IRQ4 -> 4
IRQ6 -> 6
IRQ7 -> 7
IRQ8 -> 8
IRQ9 -> 9
IRQ12 -> 12
IRQ16 -> 0
IRQ17 -> 1
IRQ20 -> 4
IRQ24 -> 8
IRQ25 -> 9
.................................... done.
calibrating APIC timer ...
..... CPU clock speed is 933.4306 MHz.
..... host bus clock speed is 133.3472 MHz.
cpu: 0, clocks: 1333472, slice: 444490
CPU0<T0:1333472,T1:888976,D:6,S:444490,C:1333472>
cpu: 1, clocks: 1333472, slice: 444490
CPU1<T0:1333472,T1:444480,D:12,S:444490,C:1333472>
checking TSC synchronization across CPUs: passed.
Setting commenced=1, go go go
PCI: PCI BIOS revision 2.10 entry at 0xf0aa0, last bus=1
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: ServerWorks host bridge: secondary bus 00
PCI: ServerWorks host bridge: secondary bus 01
PCI: Using IRQ router default [1166/0200] at 00:0f.0
PCI->APIC IRQ transform: (B1,I5,P0) -> 24
PCI->APIC IRQ transform: (B1,I5,P1) -> 25
PCI->APIC IRQ transform: (B0,I2,P0) -> 20
PCI->APIC IRQ transform: (B0,I3,P0) -> 16
PCI->APIC IRQ transform: (B0,I4,P0) -> 17
Linux NET4.0 for Linux 2.4
> > Is there anyway to restore the 8254 to a valid state without rebooting ?
>
> Well, in this specific configuration, it may be either the 8254 timer or
> the 8259 legacy PIC as when the workaround gets activated both timer IRQs
> and NMIs go through the latter. It is certainly possible to reprogram
> the chips but maybe we can find a way to avoid the lockup.
Yes, this would clearly be better.
Thank you again.
--
| Benjamin Monate | mailto:Benjamin.Monate@lri.fr |
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
Please read the FAQ at http://www.tux.org/lkml/
next prev parent reply other threads:[~2000-11-22 10:15 UTC|newest]
Thread overview: 11+ messages / expand[flat|nested] mbox.gz Atom feed top
2000-11-16 16:36 Strange lockup of the timer with 2.4.0-test10 SMP (and older) Benjamin Monate <Benjamin Monate
[not found] ` <3A15CE34.EF2FE3CC@uow.edu.au>
2000-11-20 15:31 ` Benjamin Monate <Benjamin Monate
2000-11-20 18:26 ` Fort David
2000-11-20 18:11 ` Benjamin Monate <Benjamin Monate
2000-11-20 18:13 ` Alan Cox
2000-11-21 14:31 ` Maciej W. Rozycki
2000-11-21 16:27 ` Benjamin Monate <Benjamin Monate
2000-11-21 17:35 ` Maciej W. Rozycki
2000-11-22 9:45 ` Benjamin Monate <Benjamin Monate [this message]
[not found] ` <Pine.GSO.3.96.1001123183522.6381H-100000@delta.ds2.pg.gda.pl>
2000-11-23 19:39 ` Benjamin Monate <Benjamin Monate
[not found] ` <Pine.GSO.3.96.1001127154910.13774O-100000@delta.ds2.pg.gda.pl>
2000-11-27 16:58 ` Benjamin Monate <Benjamin Monate
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=14875.38318.5084.502248@sun-demons \
--to=benjamin.monate@lri.fr \
--cc=linux-kernel@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.