Patch "Revert "i2c: designware: detect when dynamic tar update is possible"" has been added to the 4.9-stable tree

[<gregkh@linuxfoundation.org>]

This is a note to let you know that I've just added the patch titled

    Revert "i2c: designware: detect when dynamic tar update is possible"

to the 4.9-stable tree which can be found at:
    http://www.kernel.org/git/?p=linux/kernel/git/stable/stable-queue.git;a=summary

The filename of the patch is:
     revert-i2c-designware-detect-when-dynamic-tar-update-is-possible.patch
and it can be found in the queue-4.9 subdirectory.

If you, or anyone else, feels it should not be added to the stable tree,
please let <stable@vger.kernel.org> know about it.


>From 12688dc21f71f4dcc9e2b8b5556b0c6cc8df1491 Mon Sep 17 00:00:00 2001
From: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Date: Mon, 13 Feb 2017 11:18:19 +0200
Subject: Revert "i2c: designware: detect when dynamic tar update is possible"

From: Jarkko Nikula <jarkko.nikula@linux.intel.com>

commit 12688dc21f71f4dcc9e2b8b5556b0c6cc8df1491 upstream.

This reverts commit 63d0f0a6952a1a02bc4f116b7da7c7887e46efa3.

It caused a regression on platforms where I2C controller is synthesized
with dynamic TAR update disabled. Detection code is testing is bit
DW_IC_CON_10BITADDR_MASTER in register DW_IC_CON read-only but fails to
restore original value in case bit is read-write.

Instead of fixing this we revert the commit since it was preparation for
the commit 0317e6c0f1dc ("i2c: designware: do not disable adapter after
transfer") which was also reverted.

Reported-by: Shah Nehal-Bakulchandra <Nehal-bakulchandra.Shah@amd.com>
Reported-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Acked-By: Lucas De Marchi <lucas.demarchi@intel.com>
Fixes: 63d0f0a6952a ("i2c: designware: detect when dynamic tar update is possible")
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 drivers/i2c/busses/i2c-designware-core.c |   45 +++++++------------------------
 drivers/i2c/busses/i2c-designware-core.h |    1 
 2 files changed, 11 insertions(+), 35 deletions(-)

--- a/drivers/i2c/busses/i2c-designware-core.c
+++ b/drivers/i2c/busses/i2c-designware-core.c
@@ -475,30 +475,28 @@ static int i2c_dw_wait_bus_not_busy(stru
 static void i2c_dw_xfer_init(struct dw_i2c_dev *dev)
 {
 	struct i2c_msg *msgs = dev->msgs;
-	u32 ic_tar = 0;
+	u32 ic_con, ic_tar = 0;
 
 	/* Disable the adapter */
 	__i2c_dw_enable_and_wait(dev, false);
 
 	/* if the slave address is ten bit address, enable 10BITADDR */
-	if (dev->dynamic_tar_update_enabled) {
+	ic_con = dw_readl(dev, DW_IC_CON);
+	if (msgs[dev->msg_write_idx].flags & I2C_M_TEN) {
+		ic_con |= DW_IC_CON_10BITADDR_MASTER;
 		/*
 		 * If I2C_DYNAMIC_TAR_UPDATE is set, the 10-bit addressing
-		 * mode has to be enabled via bit 12 of IC_TAR register,
-		 * otherwise bit 4 of IC_CON is used.
+		 * mode has to be enabled via bit 12 of IC_TAR register.
+		 * We set it always as I2C_DYNAMIC_TAR_UPDATE can't be
+		 * detected from registers.
 		 */
-		if (msgs[dev->msg_write_idx].flags & I2C_M_TEN)
-			ic_tar = DW_IC_TAR_10BITADDR_MASTER;
+		ic_tar = DW_IC_TAR_10BITADDR_MASTER;
 	} else {
-		u32 ic_con = dw_readl(dev, DW_IC_CON);
-
-		if (msgs[dev->msg_write_idx].flags & I2C_M_TEN)
-			ic_con |= DW_IC_CON_10BITADDR_MASTER;
-		else
-			ic_con &= ~DW_IC_CON_10BITADDR_MASTER;
-		dw_writel(dev, ic_con, DW_IC_CON);
+		ic_con &= ~DW_IC_CON_10BITADDR_MASTER;
 	}
 
+	dw_writel(dev, ic_con, DW_IC_CON);
+
 	/*
 	 * Set the slave (target) address and enable 10-bit addressing mode
 	 * if applicable.
@@ -923,7 +921,6 @@ int i2c_dw_probe(struct dw_i2c_dev *dev)
 {
 	struct i2c_adapter *adap = &dev->adapter;
 	int r;
-	u32 reg;
 
 	init_completion(&dev->cmd_complete);
 
@@ -931,26 +928,6 @@ int i2c_dw_probe(struct dw_i2c_dev *dev)
 	if (r)
 		return r;
 
-	r = i2c_dw_acquire_lock(dev);
-	if (r)
-		return r;
-
-	/*
-	 * Test if dynamic TAR update is enabled in this controller by writing
-	 * to IC_10BITADDR_MASTER field in IC_CON: when it is enabled this
-	 * field is read-only so it should not succeed
-	 */
-	reg = dw_readl(dev, DW_IC_CON);
-	dw_writel(dev, reg ^ DW_IC_CON_10BITADDR_MASTER, DW_IC_CON);
-
-	if ((dw_readl(dev, DW_IC_CON) & DW_IC_CON_10BITADDR_MASTER) ==
-	    (reg & DW_IC_CON_10BITADDR_MASTER)) {
-		dev->dynamic_tar_update_enabled = true;
-		dev_dbg(dev->dev, "Dynamic TAR update enabled");
-	}
-
-	i2c_dw_release_lock(dev);
-
 	snprintf(adap->name, sizeof(adap->name),
 		 "Synopsys DesignWare I2C adapter");
 	adap->retries = 3;
--- a/drivers/i2c/busses/i2c-designware-core.h
+++ b/drivers/i2c/busses/i2c-designware-core.h
@@ -117,7 +117,6 @@ struct dw_i2c_dev {
 	int			(*acquire_lock)(struct dw_i2c_dev *dev);
 	void			(*release_lock)(struct dw_i2c_dev *dev);
 	bool			pm_runtime_disabled;
-	bool			dynamic_tar_update_enabled;
 };
 
 #define ACCESS_SWAP		0x00000001


Patches currently in stable-queue which might be from jarkko.nikula@linux.intel.com are

queue-4.9/revert-i2c-designware-detect-when-dynamic-tar-update-is-possible.patch