All of lore.kernel.org
 help / color / mirror / Atom feed
From: Jagan Teki <jagannadh.teki@gmail.com>
To: u-boot@lists.denx.de
Subject: [U-Boot] [PATCH 4/5] sun50i: h5: Add initial Orangepi Prime support
Date: Fri, 26 May 2017 01:05:10 +0530	[thread overview]
Message-ID: <1495740911-9455-5-git-send-email-jteki@openedev.com> (raw)
In-Reply-To: <1495740911-9455-1-git-send-email-jteki@openedev.com>

From: Jagan Teki <jagan@amarulasolutions.com>

Orangepi Prime is an open-source single-board computer
using the Allwinner h5 SOC.

H5 Orangepi Prime has
- Quad-core Cortex-A53
- 2GB DDR3
- Debug TTL UART
- 1000M/100M Ethernet RJ45
- Three USB 2.0
- HDMI
- Audio and MIC
- Wifi + BT
- IR receiver
- HDMI
- Wifi + BT

http://www.orangepi.org/OrangePiPrime/

Boot from MMC:
-------------
U-Boot SPL 2017.05-00662-ga3f4c05-dirty (May 25 2017 - 13:30:14)
DRAM: 2048 MiB
Trying to boot from MMC1
NOTICE:  BL3-1: Running on H5 (1718) in SRAM A2 (@0x44000)
NOTICE:  Configuring SPC Controller
NOTICE:  BL3-1: v1.0(debug):aa75c8d
NOTICE:  BL3-1: Built : 18:28:27, May 24 2017
INFO:    BL3-1: Initializing runtime services
INFO:    BL3-1: Preparing for EL3 exit to normal world
INFO:    BL3-1: Next image address: 0x4a000000, SPSR: 0x3c9

U-Boot 2017.05-00662-ga3f4c05-dirty (May 25 2017 - 13:30:14 +0000) Allwinner Technology

CPU:   Allwinner H5 (SUN50I)
Model: OrangePi Prime
DRAM:  2 GiB
MMC:   SUNXI SD/MMC: 0
*** Warning - bad CRC, using default environment

In:    serial
Out:   serial
Err:   serial
Net:   phy interface7
eth0: ethernet at 1c30000
starting USB...
USB0:   USB EHCI 1.00
USB1:   USB OHCI 1.0
scanning bus 0 for devices... 1 USB Device(s) found
       scanning usb for storage devices... 0 Storage Device(s) found
Hit any key to stop autoboot:  0

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
---
 arch/arm/dts/Makefile                     |   3 +-
 arch/arm/dts/sun50i-h5-orangepi-prime.dts | 104 ++++++++++++++++++++++++++++++
 board/sunxi/MAINTAINERS                   |   5 ++
 configs/orangepi_prime_defconfig          |  17 +++++
 4 files changed, 128 insertions(+), 1 deletion(-)
 create mode 100644 arch/arm/dts/sun50i-h5-orangepi-prime.dts
 create mode 100644 configs/orangepi_prime_defconfig

diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index 2251edf..54978cf 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -315,7 +315,8 @@ dtb-$(CONFIG_MACH_SUN8I_R40) += \
 dtb-$(CONFIG_MACH_SUN8I_V3S) += \
 	sun8i-v3s-licheepi-zero.dtb
 dtb-$(CONFIG_MACH_SUN50I_H5) += \
-	sun50i-h5-orangepi-pc2.dtb
+	sun50i-h5-orangepi-pc2.dtb \
+	sun50i-h5-orangepi-prime.dtb
 dtb-$(CONFIG_MACH_SUN50I) += \
 	sun50i-a64-orangepi-win.dtb \
 	sun50i-a64-pine64-plus.dtb \
diff --git a/arch/arm/dts/sun50i-h5-orangepi-prime.dts b/arch/arm/dts/sun50i-h5-orangepi-prime.dts
new file mode 100644
index 0000000..67eade7
--- /dev/null
+++ b/arch/arm/dts/sun50i-h5-orangepi-prime.dts
@@ -0,0 +1,104 @@
+/*
+ * Copyright (C) 2017 Jagan Teki <jteki@openedev.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This library is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This library is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+
+#include "sun50i-h5.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	model = "OrangePi Prime";
+	compatible = "xunlong,orangepi-prime", "allwinner,sun50i-h5";
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory {
+		reg = <0x40000000 0x80000000>;
+	};
+
+	soc {
+		reg_vcc3v3: vcc3v3 {
+			compatible = "regulator-fixed";
+			regulator-name = "vcc3v3";
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+		};
+	};
+};
+
+&mmc0 {
+	compatible = "allwinner,sun50i-h5-mmc",
+		     "allwinner,sun50i-a64-mmc",
+		     "allwinner,sun5i-a13-mmc";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>;
+	vmmc-supply = <&reg_vcc3v3>;
+	bus-width = <4>;
+	cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>;
+	cd-inverted;
+	status = "okay";
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_pins_a>;
+	status = "okay";
+};
+
+&usbphy {
+	status = "okay";
+};
+
+&ohci1 {
+	status = "okay";
+};
+
+&ehci1 {
+	status = "okay";
+};
diff --git a/board/sunxi/MAINTAINERS b/board/sunxi/MAINTAINERS
index ddb0b54..2d140d1 100644
--- a/board/sunxi/MAINTAINERS
+++ b/board/sunxi/MAINTAINERS
@@ -267,6 +267,11 @@ M:	Andre Przywara <andre.przywara@arm.com>
 S:	Maintained
 F:	configs/orangepi_pc2_defconfig
 
+ORANGEPI PRIME BOARD
+M:	Jagan Teki <jagan@amarulasolutions.com>
+S:	Maintained
+F:	configs/orangepi_prime_defconfig
+
 ORANGEPI WIN/WIN PLUS BOARD
 M:	Jagan Teki <jagan@amarulasolutions.com>
 S:	Maintained
diff --git a/configs/orangepi_prime_defconfig b/configs/orangepi_prime_defconfig
new file mode 100644
index 0000000..ac4bff5
--- /dev/null
+++ b/configs/orangepi_prime_defconfig
@@ -0,0 +1,17 @@
+CONFIG_ARM=y
+CONFIG_ARCH_SUNXI=y
+CONFIG_MACH_SUN50I_H5=y
+CONFIG_DRAM_CLK=672
+CONFIG_DRAM_ZQ=3881977
+CONFIG_DEFAULT_DEVICE_TREE="sun50i-h5-orangepi-prime"
+# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
+CONFIG_CONSOLE_MUX=y
+CONFIG_SPL=y
+# CONFIG_CMD_IMLS is not set
+# CONFIG_CMD_FLASH is not set
+# CONFIG_CMD_FPGA is not set
+# CONFIG_SPL_DOS_PARTITION is not set
+# CONFIG_SPL_ISO_PARTITION is not set
+# CONFIG_SPL_EFI_PARTITION is not set
+CONFIG_SUN8I_EMAC=y
+CONFIG_USB_EHCI_HCD=y
-- 
2.7.4

  parent reply	other threads:[~2017-05-25 19:35 UTC|newest]

Thread overview: 10+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2017-05-25 19:35 [U-Boot] [PATCH 0/5] sun50i: a64/h5: Add orangepi boards Jagan Teki
2017-05-25 19:35 ` [U-Boot] [PATCH 1/5] sun50i: a64: Add initial Orangepi Win/WinPlus support Jagan Teki
2017-05-25 22:54   ` André Przywara
2017-05-25 19:35 ` [U-Boot] [PATCH 2/5] arm64: dts: sun50i: Add sun50i-h5.dtsi Jagan Teki
2017-05-25 23:01   ` André Przywara
2017-05-25 19:35 ` [U-Boot] [PATCH 3/5] arm64: dts: sun50i: h5: orangepi-pc2: Use GPIO flag binding macro Jagan Teki
2017-05-25 19:35 ` Jagan Teki [this message]
2017-05-25 19:35 ` [U-Boot] [PATCH 5/5] sun50i: h5: Add initial Orangepi Zero Plus 2 support Jagan Teki
2017-05-25 23:08   ` André Przywara
2017-06-02 18:00 ` [U-Boot] [PATCH 0/5] sun50i: a64/h5: Add orangepi boards Jagan Teki

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=1495740911-9455-5-git-send-email-jteki@openedev.com \
    --to=jagannadh.teki@gmail.com \
    --cc=u-boot@lists.denx.de \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.