From: Varadarajan Narayanan <varada@codeaurora.org>
To: broonie@kernel.org, robh+dt@kernel.org, mark.rutland@arm.com,
andy.gross@linaro.org, david.brown@linaro.org,
linux-spi@vger.kernel.org, devicetree@vger.kernel.org,
linux-kernel@vger.kernel.org, linux-arm-msm@vger.kernel.org,
linux-soc@vger.kernel.org
Cc: Varadarajan Narayanan <varada@codeaurora.org>,
Matthew McClintock <mmcclint@codeaurora.org>
Subject: [PATCH v3 09/15] spi: qup: refactor spi_qup_io_config into two functions
Date: Tue, 20 Jun 2017 14:40:51 +0530 [thread overview]
Message-ID: <1497949857-1852-10-git-send-email-varada@codeaurora.org> (raw)
In-Reply-To: <1497949857-1852-1-git-send-email-varada@codeaurora.org>
This is in preparation for handling transactions larger than
64K-1 bytes in block mode, which is currently unsupported and
quietly fails.
We need to break these into two functions 1) prep is
called once per spi_message and 2) io_config is called
once per spi-qup bus transaction
This is just refactoring, there should be no functional
change
Signed-off-by: Matthew McClintock <mmcclint@codeaurora.org>
Signed-off-by: Varadarajan Narayanan <varada@codeaurora.org>
---
drivers/spi/spi-qup.c | 109 +++++++++++++++++++++++++++++++-------------------
1 file changed, 67 insertions(+), 42 deletions(-)
diff --git a/drivers/spi/spi-qup.c b/drivers/spi/spi-qup.c
index 1a83248..bfb6d27 100644
--- a/drivers/spi/spi-qup.c
+++ b/drivers/spi/spi-qup.c
@@ -543,12 +543,11 @@ static irqreturn_t spi_qup_qup_irq(int irq, void *dev_id)
return IRQ_HANDLED;
}
-/* set clock freq ... bits per word */
-static int spi_qup_io_config(struct spi_device *spi, struct spi_transfer *xfer)
+/* set clock freq ... bits per word, determine mode */
+static int spi_qup_io_prep(struct spi_device *spi, struct spi_transfer *xfer)
{
struct spi_qup *controller = spi_master_get_devdata(spi->master);
- u32 config, iomode, control;
- int ret, n_words;
+ int ret;
if (spi->mode & SPI_LOOP && xfer->len > controller->in_fifo_sz) {
dev_err(controller->dev, "too big size for loopback %d > %d\n",
@@ -563,32 +562,59 @@ static int spi_qup_io_config(struct spi_device *spi, struct spi_transfer *xfer)
return -EIO;
}
- if (spi_qup_set_state(controller, QUP_STATE_RESET)) {
- dev_err(controller->dev, "cannot set RESET state\n");
- return -EIO;
- }
-
controller->w_size = DIV_ROUND_UP(xfer->bits_per_word, 8);
controller->n_words = xfer->len / controller->w_size;
- n_words = controller->n_words;
-
- if (n_words <= (controller->in_fifo_sz / sizeof(u32))) {
+ if (controller->n_words <= (controller->in_fifo_sz / sizeof(u32)))
controller->mode = QUP_IO_M_MODE_FIFO;
+ else if (spi->master->can_dma &&
+ spi->master->can_dma(spi->master, spi, xfer) &&
+ spi->master->cur_msg_mapped)
+ controller->mode = QUP_IO_M_MODE_BAM;
+ else
+ controller->mode = QUP_IO_M_MODE_BLOCK;
+
+ return 0;
+}
+
+/* prep qup for another spi transaction of specific type */
+static int spi_qup_io_config(struct spi_device *spi, struct spi_transfer *xfer)
+{
+ struct spi_qup *controller = spi_master_get_devdata(spi->master);
+ u32 config, iomode, control;
+ unsigned long flags;
+
+ spin_lock_irqsave(&controller->lock, flags);
+ controller->xfer = xfer;
+ controller->error = 0;
+ controller->rx_bytes = 0;
+ controller->tx_bytes = 0;
+ spin_unlock_irqrestore(&controller->lock, flags);
+
+
+ if (spi_qup_set_state(controller, QUP_STATE_RESET)) {
+ dev_err(controller->dev, "cannot set RESET state\n");
+ return -EIO;
+ }
- writel_relaxed(n_words, controller->base + QUP_MX_READ_CNT);
- writel_relaxed(n_words, controller->base + QUP_MX_WRITE_CNT);
+ switch (controller->mode) {
+ case QUP_IO_M_MODE_FIFO:
+ reinit_completion(&controller->done);
+ writel_relaxed(controller->n_words,
+ controller->base + QUP_MX_READ_CNT);
+ writel_relaxed(controller->n_words,
+ controller->base + QUP_MX_WRITE_CNT);
/* must be zero for FIFO */
writel_relaxed(0, controller->base + QUP_MX_INPUT_CNT);
writel_relaxed(0, controller->base + QUP_MX_OUTPUT_CNT);
- } else if (spi->master->can_dma &&
- spi->master->can_dma(spi->master, spi, xfer) &&
- spi->master->cur_msg_mapped) {
-
- controller->mode = QUP_IO_M_MODE_BAM;
-
- writel_relaxed(n_words, controller->base + QUP_MX_INPUT_CNT);
- writel_relaxed(n_words, controller->base + QUP_MX_OUTPUT_CNT);
+ break;
+ case QUP_IO_M_MODE_BAM:
+ reinit_completion(&controller->txc);
+ reinit_completion(&controller->rxc);
+ writel_relaxed(controller->n_words,
+ controller->base + QUP_MX_INPUT_CNT);
+ writel_relaxed(controller->n_words,
+ controller->base + QUP_MX_OUTPUT_CNT);
/* must be zero for BLOCK and BAM */
writel_relaxed(0, controller->base + QUP_MX_READ_CNT);
writel_relaxed(0, controller->base + QUP_MX_WRITE_CNT);
@@ -606,19 +632,25 @@ static int spi_qup_io_config(struct spi_device *spi, struct spi_transfer *xfer)
if (xfer->tx_buf)
writel_relaxed(0, input_cnt);
else
- writel_relaxed(n_words, input_cnt);
+ writel_relaxed(controller->n_words, input_cnt);
writel_relaxed(0, controller->base + QUP_MX_OUTPUT_CNT);
}
- } else {
-
- controller->mode = QUP_IO_M_MODE_BLOCK;
-
- writel_relaxed(n_words, controller->base + QUP_MX_INPUT_CNT);
- writel_relaxed(n_words, controller->base + QUP_MX_OUTPUT_CNT);
+ break;
+ case QUP_IO_M_MODE_BLOCK:
+ reinit_completion(&controller->done);
+ writel_relaxed(controller->n_words,
+ controller->base + QUP_MX_INPUT_CNT);
+ writel_relaxed(controller->n_words,
+ controller->base + QUP_MX_OUTPUT_CNT);
/* must be zero for BLOCK and BAM */
writel_relaxed(0, controller->base + QUP_MX_READ_CNT);
writel_relaxed(0, controller->base + QUP_MX_WRITE_CNT);
+ break;
+ default:
+ dev_err(controller->dev, "unknown mode = %d\n",
+ controller->mode);
+ return -EIO;
}
iomode = readl_relaxed(controller->base + QUP_IO_M_MODES);
@@ -707,6 +739,10 @@ static int spi_qup_transfer_one(struct spi_master *master,
unsigned long timeout, flags;
int ret = -EIO;
+ ret = spi_qup_io_prep(spi, xfer);
+ if (ret)
+ return ret;
+
ret = spi_qup_io_config(spi, xfer);
if (ret)
return ret;
@@ -715,21 +751,10 @@ static int spi_qup_transfer_one(struct spi_master *master,
timeout = DIV_ROUND_UP(xfer->len * 8, timeout);
timeout = 100 * msecs_to_jiffies(timeout);
- spin_lock_irqsave(&controller->lock, flags);
- controller->xfer = xfer;
- controller->error = 0;
- controller->rx_bytes = 0;
- controller->tx_bytes = 0;
- spin_unlock_irqrestore(&controller->lock, flags);
-
- if (spi_qup_is_dma_xfer(controller->mode)) {
- reinit_completion(&controller->rxc);
- reinit_completion(&controller->txc);
+ if (spi_qup_is_dma_xfer(controller->mode))
ret = spi_qup_do_dma(master, xfer, timeout);
- } else {
- reinit_completion(&controller->done);
+ else
ret = spi_qup_do_pio(master, xfer, timeout);
- }
if (ret)
goto exit;
--
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum, hosted by The Linux Foundation
next prev parent reply other threads:[~2017-06-20 9:10 UTC|newest]
Thread overview: 26+ messages / expand[flat|nested] mbox.gz Atom feed top
2017-06-20 9:10 [PATCH v3 00/15] spi: qup: Fixes and add support for >64k transfers Varadarajan Narayanan
2017-06-20 9:10 ` [PATCH v3 01/15] spi: qup: Enable chip select support Varadarajan Narayanan
2017-06-20 9:10 ` [PATCH v3 02/15] spi: qup: Setup DMA mode correctly Varadarajan Narayanan
2017-06-20 9:10 ` [PATCH v3 03/15] spi: qup: Add completion structures for DMA Varadarajan Narayanan
2017-06-20 9:10 ` [PATCH v3 05/15] spi: qup: Place the QUP in run mode before DMA Varadarajan Narayanan
2017-06-20 9:10 ` [PATCH v3 06/15] spi: qup: Fix error handling in spi_qup_prep_sg Varadarajan Narayanan
2017-06-20 9:10 ` [PATCH v3 07/15] spi: qup: Fix transaction done signaling Varadarajan Narayanan
2017-08-08 11:18 ` Applied "spi: qup: Fix transaction done signaling" to the spi tree Mark Brown
2017-08-08 11:18 ` Mark Brown
2017-06-20 9:10 ` [PATCH v3 08/15] spi: qup: Do block sized read/write in block mode Varadarajan Narayanan
2017-06-20 9:10 ` Varadarajan Narayanan [this message]
2017-06-20 9:10 ` [PATCH v3 10/15] spi: qup: call io_config in mode specific function Varadarajan Narayanan
2017-06-20 9:10 ` [PATCH v3 11/15] spi: qup: allow block mode to generate multiple transactions Varadarajan Narayanan
2017-06-20 9:10 ` [PATCH v3 12/15] spi: qup: refactor spi_qup_prep_sg Varadarajan Narayanan
[not found] ` <1497949857-1852-1-git-send-email-varada-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>
2017-06-20 9:10 ` [PATCH v3 04/15] spi: qup: Add completion timeout Varadarajan Narayanan
2017-06-20 9:10 ` Varadarajan Narayanan
2017-06-20 9:10 ` [PATCH v3 13/15] spi: qup: allow multiple DMA transactions per spi xfer Varadarajan Narayanan
2017-06-20 9:10 ` Varadarajan Narayanan
2017-06-20 9:10 ` [PATCH v3 14/15] spi: qup: Ensure done detection Varadarajan Narayanan
2017-06-20 9:10 ` Varadarajan Narayanan
2017-06-20 9:10 ` [PATCH v3 15/15] spi: qup: support for qup v1 dma Varadarajan Narayanan
2017-06-23 21:49 ` Rob Herring
2017-06-27 9:36 ` Varadarajan Narayanan
2017-06-27 9:36 ` Varadarajan Narayanan
2017-06-28 6:47 ` Andy Gross
2017-06-28 6:47 ` Andy Gross
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1497949857-1852-10-git-send-email-varada@codeaurora.org \
--to=varada@codeaurora.org \
--cc=andy.gross@linaro.org \
--cc=broonie@kernel.org \
--cc=david.brown@linaro.org \
--cc=devicetree@vger.kernel.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-soc@vger.kernel.org \
--cc=linux-spi@vger.kernel.org \
--cc=mark.rutland@arm.com \
--cc=mmcclint@codeaurora.org \
--cc=robh+dt@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.